1、BSI Standards Publication Industrial systems, installations and equipment and industrial products Structuring principles and reference designation Part 10: Power plants PD ISO/TS 81346-10:2015National foreword This Published Document is the UK implementation of ISO/TS 81346-10:2015. The UK participa
2、tion in its preparation was entrusted to Technical Committee TDW/4, Technical Product Realization. A list of organizations represented on this committee can be obtained on request to its secretary. This publication does not purport to include all the necessary provisions of a contract. Users are res
3、ponsible for its correct application. The British Standards Institution 2015. Published by BSI Standards Limited 2015 ISBN 978 0 580 89180 9 ICS 01.110 Compliance with a British Standard cannot confer immunity from legal obligations. This Published Document was published under the authority of the S
4、tandards Policy and Strategy Committee on 31 March 2015. Amendments/corrigenda issued since publication Date Text affected PUBLISHED DOCUMENT PD ISO/TS 81346-10:2015 ISO 2015 Industrial systems, installations and equipment and industrial products Structuring principles and reference designation Part
5、 10: Power plants Systmes industriels, installations et appareils et produits industriels Principes de structuration et dsignation de rfrence Partie 10: Centrales lectriques TECHNICAL SPECIFICATION ISO/TS 81346-10 Reference number ISO/TS 81346-10:2015(E) First edition 2015-02-15 ISO/TS 81346-10:2015
6、(E)ii ISO 2015 All rights reserved COPYRIGHT PROTECTED DOCUMENT ISO 2015 All rights reserved. Unless otherwise specified, no part of this publication may be reproduced or utilized otherwise in any form or by any means, electronic or mechanical, including photocopying, or posting on the internet or a
7、n intranet, without prior written permission. Permission can be requested from either ISO at the address below or ISOs member body in the country of the requester. ISO copyright office Case postale 56 CH-1211 Geneva 20 Tel. + 41 22 749 01 11 Fax + 41 22 749 09 47 E-mail copyrightiso.org Web www.iso.
8、org Published in Switzerland PD ISO/TS 81346-10:2015 ISO/TS 81346-10:2015(E)Contents Page Foreword iv Introduction vi 1 Scope . 1 2 Normative references 1 3 T erms and definitions . 2 4 Designation systematic 5 4.1 General . 5 4.2 Process of forming designations 5 4.3 General rules for designation s
9、tructure 6 4.4 Rules for forming designations . 7 5 Designation tasks. 8 5.1 General . 8 5.2 Conjoint designation 8 5.3 Designation of technical objects Reference designation . 9 5.3.1 General 9 5.3.2 Function aspect . 9 5.3.3 Product aspect 10 5.3.4 Transition from function aspect to product aspect
10、 .10 5.3.5 Location aspect 11 5.4 Specific designations 11 5.4.1 Signal designation 11 5.4.2 Terminal designation 11 5.4.3 Document designation .12 6 Structure and contents of designation blocks 12 6.1 General 12 6.2 Designation block “Conjoint designation” 12 6.3 Function aspect12 6.3.1 Designation
11、 block “Function”.12 6.3.2 Designation block “Function allocation” 13 6.4 Product aspect Designation block “Product” 14 6.5 Transition from function aspect to product aspect 15 6.6 Location aspect 19 6.6.1 Designation block “Point of installation” .19 6.6.2 Designation block “Location” .21 6.7 Speci
12、fic designations 22 6.7.1 Signal designation 22 6.7.2 Terminal designation 25 6.7.3 Document designation .26 7 Application of designation 26 7.1 Combination of designation blocks 26 7.2 Designation notation 27 7.2.1 General.27 7.2.2 Notation in technical documents 27 7.2.3 Notation in the plant . .2
13、8 Annex A (normative) Representation of designations29 Annex B (normative) Special stipulations .31 Annex C (informative) Stipulations between parties to the project .35 Annex D (informative) Application examples 36 Bibliography .44 ISO 2015 All rights reserved iii PD ISO/TS 81346-10:2015 ISO/TS 813
14、46-10:2015(E) Foreword ISO (the International Organization for Standardization) is a worldwide federation of national standards bodies (ISO member bodies). The work of preparing International Standards is normally carried out through ISO technical committees. Each member body interested in a subject
15、 for which a technical committee has been established has the right to be represented on that committee. International organizations, governmental and non-governmental, in liaison with ISO, also take part in the work. ISO collaborates closely with the International Electrotechnical Commission (IEC)
16、on all matters of electrotechnical standardization. International Standards are drafted in accordance with the rules given in the ISO/IEC Directives, Part 2. The main task of technical committees is to prepare International Standards. Draft International Standards adopted by the technical committees
17、 are circulated to the member bodies for voting. Publication as an International Standard requires approval by at least 75 % of the member bodies casting a vote. In other circumstances, particularly when there is an urgent market requirement for such documents, a technical committee may decide to pu
18、blish other types of normative document: an ISO Publicly Available Specification (ISO/PAS) represents an agreement between technical experts in an ISO working group and is accepted for publication if it is approved by more than 50 % of the members of the parent committee casting a vote; an ISO Techn
19、ical Specification (ISO/TS) represents an agreement between the members of a technical committee and is accepted for publication if it is approved by 2/3 of the members of the committee casting a vote. An ISO/PAS or ISO/TS is reviewed after three years in order to decide whether it will be confirmed
20、 for a further three years, revised to become an International Standard, or withdrawn. If the ISO/PAS or ISO/TS is confirmed, it is reviewed again after a further three years, at which time it must either be transformed into an International Standard or be withdrawn. Attention is drawn to the possib
21、ility that some of the elements of this document may be the subject of patent rights. ISO shall not be held responsible for identifying any or all such patent rights. ISO/TS 81346-10 was prepared by Technical Committee ISO/TC 10, Technical product documentation, Subcommittee SC 10, Process plant doc
22、umentation and tpd-symbols. Documents in the 80000 to 89999 range of reference numbers are developed by collaboration between ISO and IEC. ISO 81346 consists of the following parts, under the general title Industrial systems, installations and equipment and industrial products Structuring principles
23、 and reference designation: Part 3: Application rules for a reference designation system Technical Specification Part 10: Power plants Technical Specification IEC 81346 consists of the following parts, under the general title Industrial systems, installations and equipment and industrial products St
24、ructuring principles and reference designation: Part 1: Basic rules Part 2: Classification of objects and codes for classes Further parts on sector-specific rules are under consideration.iv ISO 2015 All rights reserved PD ISO/TS 81346-10:2015 ISO/TS 81346-10:2015(E) NOTE ISO/TC 10/SC 10 and IEC/TC 3
25、 have agreed to integrate their publications on structuring principles and reference designation in the ISO/IEC 81346 series to ensure a consistent set of publications based on IEC 813461 and 2. Against this background, ISO/TS 16952-10 has been converted to ISO/TS 81346-10 following its systematic r
26、eview. At this time, apart from necessary updates, no further changes have been made. Among the issues to be considered at the next review/revision is how to make the referenced VGB publications, although recognized as having wide acceptance and authoritative status as well as being publicly availab
27、le, better accessible to ISO/IEC users, e.g. by integrating them in the ISO/IEC 81346 series. ISO 2015 All rights reserved v PD ISO/TS 81346-10:2015 ISO/TS 81346-10:2015(E) Introduction Based on ISO/TS 81346-3, this part of ISO 81346 serves to designate plants, sections of plants and items of equipm
28、ent in any type of installation for industrial production of electrical and thermal energy according to task, type and location. This sector-specific Reference Designation System (RDS) is intended for application by all engineering disciplines for the entire life cycle of a plant, from planning, lic
29、ensing, construction, operation and maintenance, re-powering, extension and recreation, to dismantling and demolition. Based on the structuring principles and reference designation rules of IEC 81346 and other documents, ISO 81346 breaks down these rules into interdisciplinary guidelines for practic
30、al application. The relationships of input documents with this part of ISO 81346 are shown in Figure 1. Figure 1 Structuring and designation standards This part of ISO 81346 establishes the prerequisites for uniform designation of all power plant processes (see Figure 2 for a summary of the energy c
31、onversion cycle), uniform designation of all power plant types, language-independent codes to ensure international applicability, adequate capacity and possible detail for designation of all systems, equipment and structures, adequate extension possibilities for new technologies, consistent designat
32、ion for planning, licensing, construction, operation, maintenance and decommissioning, common applicability in mechanical, electrical, instrumentation and control (I how the system or object is constructed (product viewpoint); where the system or object is located (location viewpoint). SOURCE: IEC 8
33、1346-1:2009, definition 3.3 3.3 auxiliary system system which is required for the support of a power plant process Note 1 to entry: This includes auxiliary steam system, compressed air, carrier air, control air, central chemicals supply, sampling systems, etc. 3.4 control purposeful action on or in
34、a process to meet specified objectives SOURCE: IEC 60050-351:2013, definition 351-42-19 Note 1 to entry: This includes measure, count, monitor, indicate, alert, record, log, manipulate, evaluate, optimize, intervene, manipulate by hand, safeguard, structure, configure, parameter, automate. 3.5 designation block structured compilation of related information units, consisting of a prefix, letters and numbers, and optionally a breakdown mark 1) Source: www.vgb.org.2 ISO 2015 All rights reserved PD ISO/TS 81346-10:2015
copyright@ 2008-2019 麦多课文库(www.mydoc123.com)网站版权所有
备案/许可证编号:苏ICP备17064731号-1