BS PD ISO TS 13399-72-2016 Cutting tool data representation and exchange Creation of documents for the standardized data exchange Definition of properties for drawing header and th.pdf

1、PD ISO/TS 13399-72:2016 Cutting tool data representation and exchange Part 72: Creation of documents for the standardized data exchange Definition of properties for drawing header and their XML-data exchange BSI Standards Publication WB11885_BSI_StandardCovs_2013_AW.indd 1 15/05/2013 15:06PD ISO/TS

2、13399-72:2016 PUBLISHED DOCUMENT National foreword This Published Document is the UK implementation of ISO/TS 13399-72:2016. The UK participation in its preparation was entrusted to Technical Committee MTE/18, Tools tips and inserts for cutting applications. A list of organizations represented on th

3、is committee can be obtained on request to its secretary. This publication does not purport to include all the necessary provisions of a contract. Users are responsible for its correct application. The British Standards Institution 2016. Published by BSI Standards Limited 2016 ISBN 978 0 580 91036 4

4、 ICS 25.100.01; 35.240.50 Compliance with a British Standard cannot confer immunity from legal obligations. This Published Document was published under the authority of the Standards Policy and Strategy Committee on 31 July 2016. Amendments issued since publication Date Text affectedPD ISO/TS 13399-

5、72:2016 ISO 2016 Cutting tool data representation and exchange Part 72: Creation of documents for the standardized data exchange Definition of properties for drawing header and their XML-data exchange Reprsentation et change des donnes relatives aux outils coupants Partie 72: Cration de la documenta

6、tion pour lchange de donnes normalises Dfinition des proprits des cartouches de plans et leur change de donnes en XML TECHNICAL SPECIFICATION ISO/TS 13399-72 Reference number ISO/TS 13399-72:2016(E) First edition 2016-07-15PD ISO/TS 13399-72:2016ISO/TS 13399-72:2016(E)ii ISO 2016 All rights reserved

7、 COPYRIGHT PROTECTED DOCUMENT ISO 2016, Published in Switzerland All rights reserved. Unless otherwise specified, no part of this publication may be reproduced or utilized otherwise in any form or by any means, electronic or mechanical, including photocopying, or posting on the internet or an intran

8、et, without prior written permission. Permission can be requested from either ISO at the address below or ISOs member body in the country of the requester. ISO copyright office Ch. de Blandonnet 8 CP 401 CH-1214 Vernier, Geneva, Switzerland Tel. +41 22 749 01 11 Fax +41 22 749 09 47 copyrightiso.org

9、 www.iso.orgPD ISO/TS 13399-72:2016ISO/TS 13399-72:2016(E)Foreword iv Introduction vi 1 Scope . 1 2 Normative references 1 3 Terms and definitions . 2 3.1 Main data . 2 3.2 Drawing data . 3 3.3 Revision data 4 3.4 Item data 4 3.5 Customer data 4 3.6 Process data . 5 3.7 Bill of material (BOM) data 5

10、 4 Additional remark to the item in the bill of material . 7 4.1 General . 7 4.2 Data fields of the XML structure 7 4.3 Special data field 9 5 XML file . 9 5.1 General . 9 5.2 XML tags . 9 5.3 Root element 10 5.4 Data element 10 5.5 XML schema determinations .10 5.5.1 XML tag .10 5.5.2 XML tag .10 5

11、.5.3 XML tag .10 5.5.4 XML tag 11 5.5.5 XML tag 11 5.5.6 XML tag 11 5.5.7 XML tag .12 5.5.8 XML tag .12 5.5.9 XML tag 12 5.5.10 XML tag .13 5.5.11 XML tag .13 5.6 Structure of the XML file 13 Annex A (informative) Example of an XML file of a turning tool 15 Annex B (informative) Structure of the XML

12、 schema .17 Bibliography .21 ISO 2016 All rights reserved iii Contents PagePD ISO/TS 13399-72:2016ISO/TS 13399-72:2016(E) Foreword ISO (the International Organization for Standardization) is a worldwide federation of national standards bodies (ISO member bodies). The work of preparing International

13、Standards is normally carried out through ISO technical committees. Each member body interested in a subject for which a technical committee has been established has the right to be represented on that committee. International organizations, governmental and non-governmental, in liaison with ISO, al

14、so take part in the work. ISO collaborates closely with the International Electrotechnical Commission (IEC) on all matters of electrotechnical standardization. The procedures used to develop this document and those intended for its further maintenance are described in the ISO/IEC Directives, Part 1.

15、 In particular the different approval criteria needed for the different types of ISO documents should be noted. This document was drafted in accordance with the editorial rules of the ISO/IEC Directives, Part 2 (see www.iso.org/directives). Attention is drawn to the possibility that some of the elem

16、ents of this document may be the subject of patent rights. ISO shall not be held responsible for identifying any or all such patent rights. Details of any patent rights identified during the development of the document will be in the Introduction and/or on the ISO list of patent declarations receive

17、d (see www.iso.org/patents). Any trade name used in this document is information given for the convenience of users and does not constitute an endorsement. For an explanation on the meaning of ISO specific terms and expressions related to conformit y assessment, as well as information about ISOs adh

18、erence to the World Trade Organization (WTO) principles in the Technical Barriers to Trade (TBT) see the following URL: www.iso.org/iso/foreword.html. The committee responsible for this document is ISO/TC 29, Small tools. ISO/TS 13399 consists of the following parts, under the general title Cutting

19、tool data representation and exchange: Part 1: Overview, fundamental principles and general information model Part 2: Reference dictionary for the cutting items Technical Specification Part 3: Reference dictionary for tool items Technical Specification Part 4: Reference dictionary for adaptive items

20、 Technical Specification Part 5: Reference dictionary for assembly items Technical Specification Part 50: Reference dictionary for reference systems and common concepts Technical Specification Part 60: Reference dictionary for connection systems Technical Specification Part 70: Graphical data layout

21、 Layer settings for tool layout Technical Specification Part 71: Graphical data layout Creation of documents for the standardized data exchange Graphical product information Technical Specification Part 72: Creation of documents for the standardized data exchange Definition of properties for drawing

22、 header and their XML-data exchange Technical Specification Part 150: Usage guidelines Technical Specification Part 201: Creation and exchange of 3D models Regular inserts Technical Specification Part 202: Creation and exchange of 3D models Irregular inserts Technical Specification Part 203: Creatio

23、n and exchange of 3D models Replaceable inserts for drilling Technical Specificationiv ISO 2016 All rights reservedPD ISO/TS 13399-72:2016ISO/TS 13399-72:2016(E) Part 204: Creation and exchange of 3D models Inserts for reaming Technical Specification Part 301: Concept for the design of 3D models bas

24、ed on properties according to ISO/TS 13399-3: Modelling of thread-cutting taps, thread-forming taps and thread-cutting dies Technical Specification Part 302: Concept for the design of 3D models based on properties according to ISO/TS 13399-3: Modelling of solid drills and countersinking tools Techni

25、cal Specification Part 303: Creation and exchange of 3D models Solid end mills Technical Specification Part 304: Creation and exchange of 3D models Solid milling cutters with arbor hole Technical Specification Part 307: Creation and exchange of 3D models End mills for indexable inserts Technical Spe

26、cification Part 308: Creation and exchange of 3D models Milling cutters with arbor hole for indexable inserts Technical Specification Part 309: Creation and exchange of 3D models Tool holders for indexable inserts Technical Specification Part 311: Creation and exchange of 3D models Solid reamers Tec

27、hnical Specification Part 312: Creation and exchange of 3D models Reamers for indexable inserts Technical Specification Part 401: Creation and exchange of 3D models Converting, extending and reducing adaptive items Technical Specification Part 403: Creation and exchange of 3D models Modelling of dri

28、ven tool units Technical Specification Part 405: Creation and exchange of 3D models Collets Technical Specification Part 406: Creation and exchange of 3D models Modelling of connection interface Technical Specification The following parts are under preparation: Part 80: Creation and exchange of 3D m

29、odels Overview and principles Technical Specification Part 100: Definitions, principles and methods for reference dictionaries Technical Specification Part 305: Creation and exchange of 3D models Modular tooling systems with adjustable cartridges for boring Technical Specification Part 310: Creation

30、 and exchange of 3D models T urning tools with carbide tips Technical Specification Part 313: Creation and exchange of 3D models Creation and exchange of 3D models Burrs Technical Specification Part 314: Creation and exchange of 3D models Creation and exchange of 3D models Cartridges for indexable i

31、nserts Technical Specification Part 315: Creation and exchange of 3D models Modelling of machine operated feed out tools T echnical Specification ISO 2016 All rights reserved vPD ISO/TS 13399-72:2016ISO/TS 13399-72:2016(E) Introduction This part of ISO/TS 13399 defines the terms, properties and defi

32、nitions of the drawing frame and drawing content of a computer-aided design. The purpose of this part of ISO/TS 13399 is to provide a common way of an electronic data exchange of graphical product information. However, the aim is the simplified communication during the phase of documentation namely

33、on the basis of 2D drawings. Within the 2D drawing, the aim is to separate the proper product description (2D graphic) from the users specific presentation (drawing header). Most of the design orders are forced to use the individual drawing frames of the users. Therefore, a big portion of the design

34、 expenditure is used for the creation of the documentation and not for the proper problem solution. Drawings are one of the most important communicative devices of a producing company. Besides the description of complex workpiece geometries, most cases are request for correspondent documentation, e.

35、g. to support NC-programming or production facilities. This part of ISO/TS 13399 defines a standardized data exchange format for documentations. Therefore, the effort for maintenance of the documentation is reduced because the product drawing of the supplier or manufacturer is merged automatically i

36、nto the individual drawing frames of the end users. This concept provides advantage for both supplier/manufacturer and end user, since the particular template is centrally maintained once only. To support a standardized electronic product data exchange, the content of drawing headers have been exami

37、ned by means of their common basic elements and the applicability. The identified data fields have been consolidated and may be used for a universal application because of a unified definition of their attributes. Thus, in a defined use case, the graphical product description (2D graphic) and the de

38、scriptive data of the product (content of the drawing header) can be merged and be filed as a complete drawing documentation.vi ISO 2016 All rights reservedPD ISO/TS 13399-72:2016TECHNICAL SPECIFICATION ISO/TS 13399-72:2016(E) Cutting tool data representation and exchange Part 72: Creation of docume

39、nts for the standardized data exchange Definition of properties for drawing header and their XML-data exchange 1 Scope This part of ISO/TS 13399 defines the necessary text elements of a drawing frame and determines a standardized data exchange format. Therefore, the effort is reduced for the mainten

40、ance of documentation because the content of a drawing header is mated into a specific drawing frame by means of using XML technology and an individual mapping table. The benefit of this concept for manufacturer/supplier and end user is the advantage of a central maintenance of the appropriate templ

41、ates. This part of ISO/TS 13399 covers the following: identification and definition of the data fields; identification and definition of the structure of the data fields; structure of the data exchange file. The standardization of drawing formats, e.g. drawing frame, structure of the bill of materia

42、l, are outside the scope of this part of ISO/TS 13399 which is rather more intended to standardize the data exchange of the product documentations. The following are outside the scope of this part of ISO/TS 13399: layer settings as defined in ISO/TS 13399-70; structure of the tool documentation as d

43、efined in ISO/TS 13399-71; applications where these standard data may be stored or referenced; concept of the classification of cutting tool data and their properties; concept of the design of 2D drawings for cutting tools; concept of the design of 3D models for cutting tools; application data for t

44、he use of those cutting tools; information about the reconditioning of cutting tools; information about additional application and usage data (e.g. coolant supply). 2 Normative references The following documents, in whole or in part, are normatively referenced in this document and are indispensable

45、for its application. For dated references, only the edition cited applies. For undated references, the latest edition of the referenced document (including any amendments) applies. ISO 2016 All rights reserved 1PD ISO/TS 13399-72:2016ISO/TS 13399-72:2016(E) ISO 10303-28, Industrial automation system

46、s and integration Product data representation and exchange Part 28: Implementation methods: XML representations of EXPRESS schemas and data, using XML schemas 3 Terms and definitions For the purposes of this document, the following terms and definitions apply. NOTE The names and the definitions of t

47、he data fields are determined. The data fields and their attributes are listed in Tables 1 and 2. Also, the data fields are put together in groups that are identical to the tags of the XML file. Fields are optional by default. In other cases, mandatory (M) or conditional (C) are set (see column “typ

48、e of field” in Tables 1 and 2). 3.1 Main data 3.1.1 supplier official name of the organization that deals with the sales and/or distribution of products and services 3.1.2 manufacturer official name of the organization that deals with the production of products and services Note 1 to entry: See ISO

49、13399-1:2006, schema: organization.organization_name. 3.1.3 drawing file unique name of the file that files electronically the drawing content in two-dimensional directions Note 1 to entry: This field can be specified as a file name or URL. Note 2 to entry: See ISO 13399-1:2006, schema: external_file_id_and_location