BS QC 221400-1997 Radio-frequency connectors RF coaxial connectors with inner diameter of outer conductor 3 mm (0 12 in) with screw coupling Characteristic impedance 50 ohms (Type .pdf

1、BRITISH STANDARD BS QC 221400:1997 IEC 169-9: 1978 (including IEC Amendment 1:1996) Radio-frequency connectors RF coaxial connectors with inner diameter of outer conductor 3 mm (0,12 in) with screw coupling Characteristic impedance 50 ohms (Type SMC) ICS 33.120.30BSQC221400:1997 This British Standar

2、d, having been prepared under the directionof the Electrotechnical Sector Board, was published underthe authority of the Standards Board and comes intoeffect on 15 January 1997 BSI 11-1998 The following BSI references relate to the work on this standard: Committee reference EPL/46/2 Draft announced

3、in BSI Update October 1996 ISBN 0 580 26360 6 Committees responsible for this British Standard The preparation of this British Standard was entrusted by Technical Committee EPL/46, Cables, wires and waveguides, RF connectors and accessories for communication and signalling, to Subcommittee EPL/46/2,

4、 RF connectors and waveguides, upon which the following bodies were represented: AEA Technology BEAMA Electrical Cable and Conductor Accessory Manufacturers British Non-Ferrous Metals Federation British Telecommunications plc Federation of the Electronics Industry Ministry of Defence National Superv

5、isory Inspectorate Society of Cable Television Engineers Amendments issued since publication Amd. No. Date CommentsBSQC221400:1997 BSI 11-1998 i Contents Page Committees responsible Inside front cover National foreword ii 1 Scope 1 2 IEC type designation 1 3 Ratings 1 4 Preferred climatic categories

6、 1 5 Dimensions General purpose connectors 1 6 Gauges and standard test connectors 4 7 Survey of patterns 8 8 Outline dimensions 10 9 Schedule for type tests 15 10 Quality assessment procedures 21 Figure 1 Untitled 2 Figure 2 Untitled 3 Figure 3 Gauge pins for centre contact of socket connector 4 Fi

7、gure 4 Untitled 5 Figure 4a Details of pin contact 5 Figure 5 Untitled 6 Figure 5a Details of contact 6 Figure 6 Free connector (straight) with socket contact 10 Figure 7 Fixed connector (single hole panel mounting with entry for r.f. cable) with pin contact 10 Figure 8 Free connector (right angle)

8、with socket contact 11 Figure 9 Fixed connector (single hole panel mounting with solder bucket) with pin contact 11 Figure 10 Fixed connector (four-hole panel mounting with solder bucket) with pin contact 12 Figure 11 Fixed connector, printed circuit mounting (straight) with pin contact 12 Figure 12

9、 Fixed connector (right angle, single hole panel mounting with solder bucket) with pin contact 13 Figure 13 Fixed connector, printed circuit mounting (right angle) with pin contact 13 Figure 14 Fixed connector (single hole panel mounting) with pin-pin contacts 14 List of references Inside back cover

10、BSQC221400:1997 ii BSI 11-1998 National foreword This British Standard has been prepared by Subcommittee EPL/46/2 and is identical with IEC 169-9:1978 Radio-frequency connectors Part 9: R.F. coaxial connectors with inner diameter of outer conductor 3 mm (0.12 in) with screw coupling Characteristic i

11、mpedance 50 ohms (Type SMC), including Amendment 1:1996, published by the International Electrotechnical Commission (IEC). IEC 169-9, also designated QC 221400, is a harmonized specification within the IEC Q system for electronic components of assessed quality. For ease of reproduction some of the t

12、ext of the French version of this international standard has been retained. References to IEC page numbers in the text should be ignored. A British Standard does not purport to include all the necessary provisions of a contract. Users of British Standards are responsible for their correct applicatio

13、n. Compliance with a British Standard does not of itself confer immunity from legal obligations. Cross-references Publication referred to a Corresponding British Standard IEC 68 BS EN 60068 Environmental testing IEC 68-2 BS EN 60068-2 Test methods IEC 68-2-1:1990 BS EN 60068-2-1:1993 Tests A. Cold I

14、EC 68-2-2:1974 BS EN 60068-2-2:1993 Tests B. Dry heat BS 2011 Environmental testing Part 2.1 Tests IEC 68-2-3 Part 2.1. Ca:1977 Test Ca. Damp heat, steady state IEC 68-2-11 Part 2.1 Ka:1982 Test Ka. Salt mist IEC 68-2-13:1983 Part 2.1M:1984 Test M. Low air pressure IEC 68-2-14 Part 2.1N:1985 Test N.

15、 Change of temperature IEC 68-2-20 Part 2.1T:1981 Test T. Soldering BS 3041 Radio-frequency connectors IEC 169-1 BS 3041-1:1977 Specification for general requirements and measuring methods BS EN 61169 Radio-frequency connectors IEC 1169-1 (QC 220000) BS EN 61169-1:1996 Generic specification. General

16、 requirements and measuring methods a Undated in text. Summary of pages This document comprises a front cover, an inside front cover, pages i and ii, pages 1 to 36, an inside back cover and a back cover. This standard has been updated (see copyright date) and may have had amendments incorporated. Th

17、is will be indicated in the amendment table on theinside front cover.BSQC221400:1997 BSI 11-1998 1 1 Scope This standard concerns patterns for r.f. coaxial connectors which may preferably be used with r.f.cables 96 IEC 50-1 or 50-2 of IEC Publication 96-2, Radio-frequency Cables, Part 2: Relevant Ca

18、ble Specifications. These connector patterns are for low power. They have a screw type coupling mechanism and are commonly known as type “SMC”. 2 IEC type designation Connectors conforming to this standard shall be designated by: a) the reference to this standard: 169-9 IEC; b) the number of the gra

19、de: 1) Grade 0 = standard test connector = G0; Grade 1 = high performance connector = G1; Grade 2 = general purpose connector, if Grade 2 is required, no grade designation is necessary; c) a serial number (see Clause 7); d) a group of figures specifying the climatic category (see Clause 4). Example

20、169-9 IEC-G1-1 (40/85/21) denotes a free socket Grade 1 high performance connector belonging to climatic category 40/85/21 to be used with a r.f.coaxial cable 96 IEC 50-1-1/2/3. NOTEThe type designation used in this standard is provisional. A final type designation is under consideration. 3 Ratings

21、This standard specifies pin and socket connectors with screw type coupling mechanism with an inner diameter of the outer conductor of 3 mm (0.12 in). Cable mounting connectors will function within specification with appropriate cables (see Clause 7) up to a frequency of at least 6 GHz, and may be us

22、ed at higher frequencies if a reflection coefficient greater than that specified can be tolerated. The connectors have a maximum working voltage of500 V 2)at sea level and of 100 V at 20000 m (44mbar). Connection of the cable may be made either by soldering or by crimping, depending upon design. The

23、 connectors may be provided with barrier and panel seals. NOTEPatterns for crimping and sealed connectors are under consideration. All connectors may be used over a temperature range of 40 C to + 85 C. Special designs may be used from 55 C to + 155 C. 4 Preferred climatic categories (see IEC Publica

24、tion 68, Basic Environmental Testing Procedures) 1) Standard test connector, Grade 0 A standard test connector is a precisely made connector of a particular series, used as a standard connector to carry out reflection coefficient measurements on Grade 1 and Grade 2 connectors. Often, the standard te

25、st connector may be part of an inter-series adaptor which allows connection with a precision (hermaphroditic) connector forming part of the measuring equipment. The dimensions and tolerances are specified in the relevant standard. High performance connector, Grade 1 A high performance connector (Gra

26、de 1) is a connector for which limits for the reflection coefficient are specified as a function of frequency in the relevant specification. No tighter tolerances than those applicable to Grade 2 are normally specified and the requirements may be agreed between manufacturer and user (specially for m

27、icrowave applications). General purpose connector, Grade 2 The general purpose connector (Grade 2) is a connector making use of the widest permitted tolerances so as still to guarantee good performance and intermateability. The requirement for the worst reflection coefficient may, or may not, be spe

28、cified. 2) All voltages specified in this standard are r.m.s. values of a.c. voltages. All test voltages are a.c. voltages of 50 Hz to 60 Hz, unless otherwise specified. Category a Temperature range Damp heat, steady state 40/85/21 40 C to + 85 C 21 days 55/155/21 55 C to + 155 C 21 days a To be inc

29、luded in the IEC type designation (see Clause 2).BSQC221400:1997 2 BSI 11-1998 5 Dimensions Connecteurs dusage gnral (classe 2) 5 Dimensions General purpose connectors (Grade 2) Les dimensions en inches sont les dimensions originales. Toutes les reprsentations non cotes sont donnes pour rfrence uniq

30、uement. Inch dimensions are original dimensions. All undimensioned pictorial configurations are for reference purposes only. 5.1 Connector with pin centre contact Figure 1 Reference mm inch Note Min. Max. Min. Max. a 3,71 0,146 diameter c 2,08 0,082 diameter d 2 e 0,48 0,53 0,019 0,021 diameter f 0,

31、25 0,010 g 3,40 0,134 h 3,40 0,134 k 0,000 0,000 m 3,12 3,38 0,123 0,133 n 5,94 0,234 1 p 0,61 0,024 q 2,13 0,084 s 3,05 0,120 diameter nom. NOTE 1Thread gauge to go this minimum distance. NOTE 2Chosen diameter to give required 50 W impedance.BSQC221400:1997 BSI 11-1998 3 5.2 Connector with socket c

32、entre contact Figure 2 Reference mm inch Note Min. Max. Min. Max. a 3,73 0,147 diameter b 3,07 0,121 5 diameter c 2,06 0,081 diameter d 4 e 3 f 1 g 3,40 0,134 h 2,85 3,40 0,112 0,134 k 0,00 0,000 m 2,79 0,110 n 5,92 0,233 2 p 2,79 0,110 u 3,10 0,122 s 3,05 0,120 diameter nom. NOTE 1Method of slottin

33、g optional. Closing of socket to give required electrical and mechanical performance. NOTE 2Dimension when coupling nut biased forward. NOTE 3Diameter of bore to meet electrical and mechanical requirements. NOTE 4Diameter chosen to give 50 W impedance. NOTE 5Applicable at the reference plane.BSQC221

34、400:1997 4 BSI 11-1998 Figure 3 Gauge pins for centre contact of socket connector 6. Calibres et connecteurs dessai de rfrence (classe 0) 6. Gauges and standard test connectors (Grade 0) 6.1 Calibres mcaniques 6.1 Mechanical gauges 6.1.1 Connecteurs avec contact central femelle 6.1.1 Connector with

35、socket centre contact 6.1.1.1 Squence dessai 6.1.1.1 Test sequence a) Une broche en acier (Figure 3) avec un diamtre minimal “a” de mm ( in) doit tre introduite dans le contact central lectrique sur une distance minimale de 1,27 mm (0,05 in). a) A steel test pin (Figure 3) with a minimum diameter “a

36、” of mm ( in) shall be inserted into the centre electrical contact a minimum distance of1.27 mm (0.05 in). b) Une deuxime broche (Figure 3) avec un diamtre maximal “a” de mm ( in) et une rugosit de 0,4 mm (16min) doit avoir une force minimale de rtention de 0,28 N aprs insertion dans le contact cent

37、ral lectrique. II est recommand que ce calibre ait une masse (poids) de 28 1 g. b) A second steel test pin (Figure 3) with a maximum diameter “a” of mm ( in) and a 0,4 mm (16 min) finish shall have a minimum withdrawal force of0.28 N after insertion into the centre electrical contact. It is recommen

38、ded that this gauge should have a mass (weight) of 28 1 g. Lopration de calibrage du point a) peut seulement tre effectue si le contact femelle peut tre retir du connecteur. The sizing operation of item a) can only be carried out if the socket contact can be removed from the connector. Sil nest pas

39、possible deffectuer lopration de calibrage sur les connecteurs, les prescriptions du point b) doivent cependant tre satisfaites. If it is not possible to carry out the sizing operation on connectors, the requirements of item b), however, have to be met. 6.2 Connecteurs dessai de rfrence (classe0) 6.

40、2 Standard test connectors (Grade 0) Les connecteurs dessai de rfrence sont principalement utiliss comme partie du raccord lquipement de mesure afin deffectuer la mesure du coefficient de rflexion selon le paragraphe 14.1 de la Publication 169-1 de laCEI: Connecteurs pour frquences radiolectriques,

41、Premire partie: Rgles gnrales et mthodes de mesure. Standard test connectors are mainly used as part of the adaptor to the measuring equipment to carry out reflection coefficient measurement according to Sub-clause 14.1 of IEC Publication 169-1, Radio-frequency connectors, Part 1: General Requiremen

42、ts and Measuring Methods. 0,546 +0,005 0 0,0215 + 0,0002 0 0.546 +0.005 0 0.0215 +0.0002 0 0,482 0 0,005 0,0190 0 0,0002 0.482 0 0.005 0.0190 0 0.0002BSQC221400:1997 BSI 11-1998 5 6.2.1 Connecteurs dessai de rfrence avec contact central mle 6.2.1 Standard test connector with pin centre contact Figur

43、e 4 Figure 4a Details of pin contact Rf. Ref mm in Note Min. Max. Min. Max. a 3,658 3,708 0,144 0,146 diam. b 3,048 3,073 0,120 0,121 diam. c 2,083 2,159 0,082 0,085 diam. d 1 e 0,495 0,521 0,0195 0,0205 diam. f 0,25 0,010 diam. g 3,404 3,607 0,134 0,142 h 3,404 3,505 0,134 0,138 k 0,00 0,127 0,000

44、0,005 p 2,515 2,616 0,099 0,103 q 1,524 1,626 0,060 0,064 s 0,102 0,178 0,004 0,007 chamfer w 0,075 0,003BSQC221400:1997 6 BSI 11-1998 NOTE 1Diamtre du conducteur central et longueur dune section uniforme dune ligne de transmission pour obtenir limpdance caractristique requise de 50,0 0,5 W. NOTE 1D

45、iameter of centre conductor and length of uniform section of transmission line to give required characteristic impedance of 50.0 0.5 W. Les dimensions non indiques dans ce tableau sont incluses dans le tableau du paragraphe 5.1. Dimensions not indicated in this table are included in the table of Sub

46、-clause 5.1. 6.2.2 Connecteur dessai de rfrence avec contact central femelle 6.2.2 Standard test connector with socket centre contact Figure 5 Figure 5a Details of contactBSQC221400:1997 BSI 11-1998 7 Rf. Ref. mm in Note Min. Max. Min. Max. a 3,734 3,810 0,147 0,150 b 3,048 3,073 0,120 0,121 c 2,007

47、 2,057 0,079 0,081 d 1 e 3 diam. g 3,302 3,404 0,130 0,134 h 3,226 3,404 0,127 0,134 k 0,00 0,152 0,000 0,006 p 2,79 0,110 q 1,52 1,78 0,060 0,070 r 1,0058 1,0262 0,0396 0,0404 2 t 3,366 3,493 0,1325 0,1375 u 3,048 3,099 0,120 0,122 v 0,127 0,229 0,005 0.009 w 0,07 0,003 x 0,127 0,005 NOTE 1Diamtre

48、du conducteur central et de la section uniforme de la ligne de transmission pour obtenir limpdance caractristique requise de 50,0 0,5 W. NOTE 1Diameter of centre conductor and of uniform section of transmission line to give required characteristic impedance of50,0 0,5 W. NOTE 2Sapplique avec le calibre mle de diamtre 0,508 mm (0,020 in) introduit. NOTE 2Applies with 0,508 mm (0,020 in) diameter gauge pin inserted. NOTE 3Le diamtre intrieur doit tre tel que lorsquune broche de diamtre 0,508 mm (0,020 in) est introduite le diamtre extrieur “r” soit dans