BS S 151-1975 Specification for chromium-nickel-molybdenum-vanadium heat-resisting steel billets bars forgings and parts (930-1130 MPa limiting ruling section 150 mm) (Cr 12 Ni 2 5.pdf

1、BRITISH STANDARD AEROSPACE SERIES BS S 151:1975 Incorporating Amendments Nos. 1 and 2 Specification for Chromium-nickel- molybdenum-vanadium heat-resisting steel billets, bars, forgings and parts (9301130 MPa: limiting ruling section 150 mm) (Cr 12, Ni 2.5, Mo 1.7, V 0.3) UDC 629.7:669.15 262428 292

2、 4:669.14.018.4 BS S 151:1975 This British Standard, having been approved by the Aerospace Industry Standards Committee, was published under the authority of the Executive Board on 30 September 1975 BSI 14 October 2002 The following BSI references relate to the work on this standard: Committee refer

3、ence ACE/15 Draft for comment 73/32574 DC ISBN 0 580 08750 6 Foreword This publication has been prepared by Technical Committee ACE/15, Wrought and cast steels for aerospace. The start and finish of text introduced or altered by amendment is indicated in the text by tags . Tags indicating changes to

4、 text carry the number of the amendment. For example, text altered by amendment No. 1 is indicated by . This publication does not purport to include all the necessary provisions of a contract. Users are responsible for its correct application. Compliance with a British Standard does not of itself co

5、nfer immunity from legal obligations. Summary of pages This document comprises a front cover, an inside front cover, pages i and ii, pages 1 and 2, an inside back cover and a back cover. The BSI copyright notice displayed in this document indicates when the document was last used. Amendments issued

6、since publication Amd. No. Date Comments 3783 31 December 1981 See foreword 13678 14 October 2002 See forewordBS S 151:1975 BSI 14 October 2002 i Contents Page Foreword Inside front cover 1 Inspection and testing procedure 1 2 Manufacture 1 3 Chemical composition 1 4 Surface dressing 1 5 Condition 2

7、 6 Heat treatment 2 7 Mechanical properties 2ii blankBS S 151:1975 BSI 14 October 2002 1 NOTE This specified chemical composition compiles with AECMA Recommendation FEPM37 1 Inspection and testing procedure 1.1 General. This British Standard shall be used in conjunction with the relevant sections of

8、 the latest issue of BS S 100 as follows: 1.2 Sulphur printing or deep etching tests. One sample shall be taken from each ingot for sulphur printing or deep etching tests. 1.3 Ultrasonic examination. The material shall be ultrasonically tested in accordance with BS S 100, Annex B. 2 Manufacture The

9、material shall be manufactured by an electric process. 3 Chemical composition The steel shall contain: 4 Surface dressing The material shall be overall dressed. Bars for machining delivered in the finally heat treated condition Sections 1 and 3 Forging stock and billets and bars for subsequent worki

10、ng Sections 1 and 5 Forgings Sections 1 and 6 Parts finally heat treated after machining Sections 1 and 7 Element % min. max. Carbon 0.08 0.13 Silicon 0.35 Manganese 0.5 0.9 Phosphorus 0.030 Sulphur 0.025 Chromium 11.0 12.5 Molybdenum 1.5 2.0 Nickel 2.0 3.0 Vanadium 0.25 0.40 Nitrogen 0.020 0.040BS

11、S 151:1975 2 BSI 14 October 2002 5 Condition 5.1 The material shall be supplied in the appropriate condition stated below: 5.2 Parts shall be supplied finally heat treated. 6 Heat treatment 6.1 Softening treatment. The material shall be softened by heating uniformly at a temperature between 670 C an

12、d 720 C for not less than 6 h, followed by cooling in air. 6.2 Final heat treatment 6.2.1 The material, parts and test samples shall be heat treated as follows: a) Hardening. Heat at a temperature of 1 050 10 C, followed by cooling in air. b) Tempering. Heat at a temperature of 650 5 C, followed by

13、cooling in air. 6.2.2 Where bars delivered in the finally heat treated condition have been subjected to a cold straightening or cold rolling operation, they may be given a stress relieving treatment. If a stress relieving treatment is applied this shall be sufficient to restore the proof stress. 7 M

14、echanical properties 7.1 Tensile test at room temperature and impact test. The mechanical properties obtained from test pieces shall be as follows: Note deleted 7.2 Hardness test 7.2.1 The hardness of material heat treated in accordance with 6.1 shall be not greater than 311 HB. 7.2.2 The hardness o

15、f material, parts and test samples heat treated in accordance with 6.2 shall be: 286 min./331 max. HB or 300 min./350 max. HV Designation Form Condition of supply S151B Black bars for machining Finally heat treated S151D Bright bars for machining Finally heat treated before or after cold drawing or

16、cold rolling or machining or grinding S151A Forging stock and billets and bars for subsequent working Softened S151C Forgings Finally heat treated 0.2 % proof stress Tensile strength Elongation Reduction of area Izod impact min. min. max. min. min. min. MPa MPa MPa % % ftlbf 760 930 1 130 14 40 45 F

17、ootnote deleted blankBS S 151:1975 BSI 389 Chiswick High Road London W4 4AL BSI British Standards Institution BSI is the independent national body responsible for preparing British Standards. It presents the UK view on standards in Europe and at the international level. It is incorporated by Royal C

18、harter. Revisions British Standards are updated by amendment or revision. Users of British Standards should make sure that they possess the latest amendments or editions. It is the constant aim of BSI to improve the quality of our products and services. We would be grateful if anyone finding an inac

19、curacy or ambiguity while using this British Standard would inform the Secretary of the technical committee responsible, the identity of which can be found on the inside front cover. Tel: +44 (0)20 8996 9000. Fax: +44 (0)20 8996 7400. BSI offers members an individual updating service called PLUS whi

20、ch ensures that subscribers automatically receive the latest editions of standards. Buying standards Orders for all BSI, international and foreign standards publications should be addressed to Customer Services. Tel: +44 (0)20 8996 9001. Fax: +44 (0)20 8996 7001. Email: ordersbsi-. Standards are als

21、o available from the BSI website at http:/www.bsi-. In response to orders for international standards, it is BSI policy to supply the BSI implementation of those that have been published as British Standards, unless otherwise requested. Information on standards BSI provides a wide range of informati

22、on on national, European and international standards through its Library and its Technical Help to Exporters Service. Various BSI electronic information services are also available which give details on all its products and services. Contact the Information Centre. Tel: +44 (0)20 8996 7111. Fax: +44

23、 (0)20 8996 7048. Email: infobsi-. Subscribing members of BSI are kept up to date with standards developments and receive substantial discounts on the purchase price of standards. For details of these and other benefits contact Membership Administration. Tel: +44 (0)20 8996 7002. Fax: +44 (0)20 8996

24、 7001. Email: membershipbsi-. Information regarding online access to British Standards via British Standards Online can be found at http:/www.bsi- Further information about BSI is available on the BSI website at http:/www.bsi-. Copyright Copyright subsists in all BSI publications. BSI also holds the

25、 copyright, in the UK, of the publications of the international standardization bodies. Except as permitted under the Copyright, Designs and Patents Act 1988 no extract may be reproduced, stored in a retrieval system or transmitted in any form or by any means electronic, photocopying, recording or o

26、therwise without prior written permission from BSI. This does not preclude the free use, in the course of implementing the standard, of necessary details such as symbols, and size, type or grade designations. If these details are to be used for any other purpose than implementation then the prior written permission of BSI must be obtained. Details and advice can be obtained from the Copyright & Licensing Manager. Tel: +44 (0)20 8996 7070. Fax: +44 (0)20 8996 7553. Email: copyrightbsi-.