A-A-59485-2000 PLASTIC MATERIAL PRESSURE SENSITIVE ADHESIVE FOR AEROSPACE IDENTIFICATION AND MARKING [Superseded DLA MIL-P-38477 A CANC NOTICE 2 DLA MIL-P-38477 A VALID NOTICE 1 DL.pdf

1、INCH-POUNDA-A-5948524 February 2000SUPERSEDINGMIL-P-38477A30 August 1973Beneficial comments, recommendations, additions, deletions, clarifications, etc. and any datathat may improve this document should be sent to: Defense Supply Center Richmond(DSCR), ATTN: DSCR-VBD, 8000 Jefferson Davis Highway, R

2、ichmond, VA 23297-5610.AMSC N/A FSC 9330DISTRIBUTION STATEMENT A. Approved for public release; distribution is unlimited.COMMERCIAL ITEM DESCRIPTIONPLASTIC MATERIAL, PRESSURE SENSITIVE ADHESIVE,FOR AEROSPACE IDENTIFICATION AND MARKINGThe General Services Administration has authorized the use of this

3、commercial item description for all federal agencies.1. SCOPE. This commercial item description (CID) covers an adhesive-backed, pigmented orclear polyester plastic film for marking of aerospace interior and exterior surfaces.2. CLASSIFICATION. Marking material covered by this commercial item descri

4、ption shall be ofthe following types and classes. The selected types and classes of the product to be supplied shallbe specified in the acquisition order (see 6.1(b).Type I - Non perforatedType II - PerforatedClass 1 - PlainClass 2 - With protective masking sheet applied to the face side of the mark

5、ing material3. SALIENT CHARACTERISTICS3.1 Composition. The marking material shall consist of material, color configuration, size,physical properties and requirements of table I.3.1.1 Material. The material shall consist of a pigmented or clear polyester plastic film, with apressure sensitive adhesiv

6、e applied to one side. The adhesive backing shall be protected by asuitable liner, which can be easily removed without the use of water or solvents.Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-A-A-594852TABLE I. Physical properties and performance

7、 characteristics.Property RequirementsColor VariousFilm Thickness 0.005 inch maximumTensile Strength 18 lbs./inch width minimumElongation 50% minimumShrinkage 1/64 inch maximumFlexibilityStandard Conditions 20 folds minimum without failureLow Temperature No failureHeat Aging No failureAdhesion at St

8、d. Conditions 40 oz./inch width minimumAdhesion at Low Temperature 35 oz./inch width minimumOverlaid Colors No delaminationPly No separation of film and adhesiveCorrosivity NoneImmersion ResistanceWater No effectFuel No effectHot Oil No effectSalt Spray No effectAccelerated Weather Resistance No fai

9、lureOutdoor Weather Resistance No failureStorage Stability 12 months minimum3.1.2 Color. The color of the marking material shall be either inherent in the basic film oroverlaid on the basic film (see 6.1(c).3.1.3 Finishing coat. The basic film colors or the overlaid colors shall have either a specul

10、ar ornon-specular finishing coat (see 6.1(d).3.1.4 Configuration.3.1.4.1 Type I. Type I material shall consist of a smooth, uniform film without pinholes or otherdefects in the film surface.Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-A-A-5948533.

11、1.4.2 Type II. Type II material shall be the same as type I material, except that the surface shallbe perforated with clean die punched holes, 0.025 inches maximum diameter, positioned in a0.250 inch square grid pattern.3.1.4.3 Class 1. Class 1 material shall consist of the plastic film, adhesive ba

12、cking and protectiveliner, and shall be applicable to both type I and type II.3.1.4.4 Class 2. Class 2 material shall be the same as class 1 material, except that it shallincorporate a protective transfer sheet applied to the face side of the marking material. Thetransfer sheet shall be paper or fil

13、m.3.1.5 Size. The marking material shall be furnished in rolls and sheets as specified (see 6.1(e).3.1.5.1 Roll length. The length of the roll shall be up to 50 yards. 3.1.5.2 Width. The width of the material should range from 1 inch to 36 inches.3.1.5.3 Thickness. The maximum material thickness sha

14、ll be 0.005.3.1.6 Physical properties and performance characteristics. Type I and type II marking materialshall meet the requirements of table I when tested. 3.2 Toxicity. Solvents and other compounds retained in the marking material shall have no effecton the health of personnel when the material i

15、s used for its intended purpose.3.3 Workmanship. The material shall be free from blisters, cracks, foreign matter, or any otherdefects.4. QUALITY ASSURANCE PROVISIONS4.1 Product conformance. The products provided shall meet the salient characteristics of thiscommercial item description, conform to t

16、he producers own drawings, specifications, standards,and quality assurance practices, and be the same product offered for sale in the commercialmarketplace. The government reserves the right to require proof of such conformance.4.2 Market acceptability. The following market acceptability criteria ar

17、e necessary to documentthe quality of the product to be provided under this CID.4.2.1 The company must be able to show test data lab results of meeting the salientcharacteristics of the plastic material.4.2.2 The company must provide a warranty of replacing defective items.Provided by IHSNot for Res

18、aleNo reproduction or networking permitted without license from IHS-,-,-A-A-5948544.2.3 The company must have produced or distributed plastic material meeting the requirementsof this CID for at least 2 years.5. PACKAGING5.1 Preservation, packing, and marking. For acquisition purposes, the marking ma

19、terial shall bepreserved, packed, and marked as specified in the acquisition order (see 6.1(f).6. NOTES6.1 Ordering data. Acquisition documents must specify the following information:a. Title, number, and date of this documentb. Product classification (type and class) (see 2.)c. Color, inherent or o

20、verlaid (see 3.1.2)d. Finishing coat, specular or non-specular (see 3.1.3)e. Size required (see 3.1.5)f. Packaging requirements (see 5.1)6.2 Part identification number (PIN). The following part identification numbering system is forgovernment purposes and does not constitute a requirement for the co

21、ntractor.Class: 1 - Plain2 - With protective masking sheet applied to the faceside of the marking materialType: A - Type I - Non perforatedB - Type II - PerforatedAA59485 - X XCID numberProvided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-A-A-5948556.3 Na

22、tional stock number (NSN). The NSNs listed in table II correspond to the markingmaterial in this CID. This list may not be indicative of all possible NSNs associated with the CID.TABLE II. Assigned NSNs.Type Class Assigned NSNI 1 9330-00-405-98619330-00-839-09079330-01-144-11129330-01-281-3548II 1 9

23、330-01-020-3644II 2 9330-00-463-42779330-00-470-4633MILITARY INTERESTS:CIVIL AGENCYCOORDINATING ACTIVITY:Custodians:Army - EANavy - OSAir Force - 11GSA - 7FXEPreparing activity:DLA - GS(Project 9330-0121)Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-