ImageVerifierCode 换一换
格式:PDF , 页数:24 ,大小:221.05KB ,
资源ID:400794      下载积分:5000 积分
快捷下载
登录下载
邮箱/手机:
温馨提示:
快捷下载时,用户名和密码都是您填写的邮箱或者手机号,方便查询和重复下载(系统自动生成)。 如填写123,账号就是123,密码也是123。
特别说明:
请自助下载,系统不会自动发送文件的哦; 如果您已付费,想二次下载,请登录后访问:我的下载记录
支付方式: 支付宝扫码支付 微信扫码支付   
验证码:   换一换

加入VIP,免费下载
 

温馨提示:由于个人手机设置不同,如果发现不能下载,请复制以下地址【http://www.mydoc123.com/d-400794.html】到电脑端继续下载(重复下载不扣费)。

已注册用户请登录:
账号:
密码:
验证码:   换一换
  忘记密码?
三方登录: 微信登录  

下载须知

1: 本站所有资源如无特殊说明,都需要本地电脑安装OFFICE2007和PDF阅读器。
2: 试题试卷类文档,如果标题没有明确说明有答案则都视为没有答案,请知晓。
3: 文件的所有权益归上传用户所有。
4. 未经权益所有人同意不得将文件中的内容挪作商业或盈利用途。
5. 本站仅提供交流平台,并不能对任何下载内容负责。
6. 下载文件中如有侵权或不适当内容,请与我们联系,我们立即纠正。
7. 本站不保证下载资源的准确性、安全性和完整性, 同时也不承担用户因使用这些下载资源对自己和他人造成任何形式的伤害或损失。

版权提示 | 免责声明

本文(ABS 211 NOTICE 1-2017 GUIDE FOR BUILDING AND CLASSING INTERNATIONAL NAVAL SHIPS 2017.pdf)为本站会员(deputyduring120)主动上传,麦多课文库仅提供信息存储空间,仅对用户上传内容的表现方式做保护处理,对上载内容本身不做任何修改或编辑。 若此文所含内容侵犯了您的版权或隐私,请立即通知麦多课文库(发送邮件至master@mydoc123.com或直接QQ联系客服),我们立即给予删除!

ABS 211 NOTICE 1-2017 GUIDE FOR BUILDING AND CLASSING INTERNATIONAL NAVAL SHIPS 2017.pdf

1、 GUIDE FOR BUILDING AND CLASSING INTERNATIONAL NAVAL SHIPS 2017 NOTICE NO. 1 JULY 2017 The following Rule Changes were approved by the ABS Rules Committee on 30 May 2017 and become EFFECTIVE AS OF 1 JULY 2017. (See http:/www.eagle.org for the consolidated version of the Guide for Building and Classi

2、ng International Naval Ships 2017, with all Notices and Corrigenda incorporated.) Notes - The date in the parentheses means the date that the Rule becomes effective for new construction based on the contract date for construction, unless otherwise noted. (See 1-1-4/3.3 of the ABS Rules for Condition

3、s of Classification (Part 1).) PART 3 HULL CONSTRUCTION AND EQUIPMENT CHAPTER 2 HULL STRUCTURES AND ARRANGEMENTS SECTION 14 RUDDERS AND STEERING EQUIPMENT 17 Double Plate Rudder (Revise Paragraph 3-2-14/17.1 and add new 3-2-14/Figures 5, 6, and 7, as follows:) 17.1 Strength (1 July 2017) Rudder sect

4、ion modulus and web area are to be such that stresses indicated in the following Subparagraphs are not exceeded. In calculating the section modulus of the rudder, the effective width of side plating is to be taken as not greater than twice the extreme athwartship dimension of the rudder in way of ho

5、rizontal section being considered. Bolted cover plates on access or inspection openings to pintles or nuts are not to be considered effective in determining the section modulus of the rudder. In order for a cover plate to be considered effective, it is to be closed using a full penetration weld and

6、confirmed suitable by non-destructive testing method. Smooth curvature or radii are to be provided at abrupt changes in section where stress concentrations occur, including in way of openings and cover plates. When inspection windows are located in the panel below the rudder hub, the stress is to be

7、 as permitted in way of cutouts. Moments, shear forces and reaction forces are to be obtained by direct calculation, which is to be submitted. Guidance for calculation of these values is given in Appendix 3-2-A4. For spade rudders and rudders with horns, the section modulus at the bottom of the rudd

8、er is not to be less than one-third the required section modulus of the rudder at the top of the rudder or at the center of the lowest pintle. Special attention is to be paid in design and construction of rudders with slender foil sections in the vicinity of their trailing edge (e.g., hollow foil se

9、ctions, fishtail foil sections). Where the width of the rudder blade at the aftermost vertical diaphragm, w, is equal or less than 1/6of the trailing edge length measured between the diaphragm and the trailing edge, , finite element vibration analysis of the rudder blade is also to be submitted for

10、review. See 3-2-14/Figure 5. ABSGUIDE FOR BUILDING AND CLASSING INTERNATIONAL NAVAL SHIPS .2017 1 Notice No. 1 July 2017 FIGURE 5 (1 July 2017) wSpade rudders with an embedded rudder trunk are to have a trailing edge with dimensions that satisfy the following requirements: i) For a rudder trailing e

11、dge having a monotonous transition to a rounded end with a finite thickness or diameter (see 3-2-14/Figure 6), the vortex shedding frequency calculated using the equation given below is to be higher than 35 Hz. fs= TDUSTDt +where fs= vortex shedding frequency, in Hz U = flow velocity, in m/s (ft/s),

12、 which is taken as vessels design speed with vessel running ahead at the maximum continuous rated shaft rpm and at the summer load waterline St= nominal Strouhal number = 0.18 D= 0.27 C = minimal chord length of rudder cross section profile, in m (ft) D = nominal boundary layer thickness at trailing

13、 edge = 0.01C T= 0.77 T = thickness or diameter of rounded end, in m (ft) FIGURE 6 (1 July 2017) Thickness or Diameter of Rounded End2 ABSGUIDE FOR BUILDING AND CLASSING INTERNATIONAL NAVAL SHIPS .2017 Notice No. 1 July 2017 ii) For a rudder trailing edge with a flat insert plate (see 3-2-14/Figure

14、7), the insert plate thickness, t0, is to be no larger than 1.5Vdin mm, where Vdis the design speed in ahead condition, in knots, as defined in 3-2-14/3.1. The extension beyond the weld to rudder plate, , is to satisfy the following 3-2-14/Figure 7 and with consideration of possible local vibratory

15、bending of the insert plate. FIGURE 7 (1 July 2017) Insert Plate Thicknesst0Rudder Plate Thicknesst1 (t0+ 2t1)Alternatively, a vibration analysis is to be carried out to confirm that the natural frequency of the rudder is to be at least 20% away from the vortex shedding frequency preferably determin

16、ed using either a detailed numerical analysis method such as CFD or testing for ballast and full draft at 85% and 100% Vdas defined in 3-2-14/3.1. (Renumber existing 3-2-14/Figures 5 through 11 as 3-2-14/Figures 8 through 14.) (Revise Subparagraph 3-2-14/17.1.2, as follows:) 17.1.2 In way of Cutouts

17、 Allowable stresses for determining the rudder strength in way of cutouts (see 3-2-14/Figure 8) are as follows: Bending stress b= K/Q N/mm2(kgf/mm2, lbs/in2) Shear stress = K/Q N/mm2(kgf/mm2, lbs/in2) Equivalent stress e= 223 +b= Ke/Q N/mm2(kgf/mm2, lbs/in2) where SI units MKS units US units K75 7.6

18、5 10,900 K50 5.1 7,300 Ke100 10.2 14,500 Q = 1.0 for ordinary strength hull steel = as defined in 3-2-1/5.3 for higher strength steel and aluminum plate ABSGUIDE FOR BUILDING AND CLASSING INTERNATIONAL NAVAL SHIPS .2017 3 Notice No. 1 July 2017 FIGURE 8 Z6r26r16r1r26r2XNote:r1= corner radius of rudd

19、er plate in way ofportable bolted inspection holer2= corner radius of rudder plateIn way ofcutoutsr1PART 4 VESSEL SYSTEMS AND MACHINERY CHAPTER 2 PRIME MOVERS SECTION 1 DIESEL ENGINES 13 Testing, Inspection and Certification of Diesel Engines 13.9 Shop Tests of Internal Combustion, I.C. Engines (1 J

20、uly 2016) 13.9.2 Engines Driving Propellers or Impellers Only (Revise Item 4-2-1/13.9.2iv), as follows:) iv) (1 July 2017) 90% (or normal continuous cruise power), 75%, 50% and 25% of rated power, in accordance with the nominal propeller curve (the sequence to be selected by the engine manufacturer)

21、. 4 ABSGUIDE FOR BUILDING AND CLASSING INTERNATIONAL NAVAL SHIPS .2017 Notice No. 1 July 2017 (Revise 4-2-1/Table 1, as follows:) TABLE 1 Required Material and Nondestructive Tests of Diesel Engine Parts(1)(1 July 2017) Engine Part Material Properties (2)Nondestructive Tests for which purpose, plans

22、 and data as required by 4-2-2/1.5 are to be submitted to ABS for approval, showing compliance with the requirements of this Section. A unit of the same type is to be satisfactorily containment and type tested, as required by 4-2-2/5.3 and 4-2-2/5.7. ABSGUIDE FOR BUILDING AND CLASSING INTERNATIONAL

23、NAVAL SHIPS .2017 9 Notice No. 1 July 2017 ii) Turbochargers of category C are to be surveyed during their construction for compliance with the design approved, along with, but not limited to, material tests, hydrostatic tests, dynamic balancing, performance tests, etc., as indicated in 4-2-2/11.1,

24、all to be carried out to the satisfaction of the Surveyor. iii) Each turbocharger required to be certified by 4-2-2/1.1 is to be delivered with certificates indicating compliance with the requirements of this section and the applicable type approval. 11.3.2 Approval Under the Type Approval Program 1

25、1.3.2(a) Product Design Assessment. Upon application by the manufacturer, each model of a type of turbocharger is to be design assessed as described in 1-1-A3/5.1 of the ABS Rules for Conditions of Classification (Part 1). For this purpose, each design of a turbocharger type is to be approved in acc

26、ordance with 4-2-2/11.3.1i). Turbochargers so approved may be applied to ABS for listing on the ABS website as Products Design Assessed. Once listed, and subject to renewal and updating of the certificate as required by 1-1-A3/5.7 of the ABS Rules for Conditions of Classification (Part 1), turbochar

27、ger particulars will not be required to be submitted to ABS each time the turbocharger is proposed for use on board a vessel. 11.3.2(b) Manufacturing Assessment for Turbochargers. A manufacturer of turbochargers, who operates a quality assurance system in the manufacturing facilities, may apply to A

28、BS for quality assurance assessment described in 1-1-A3/5.3.1(a) (Manufacturers Procedure), 1-1-A3/5.3.1(b) (RQS) or 1-1-A3/5.5 (PQA (IACS UR Z26 Alternative Certification Scheme) of the ABS Rules for Conditions of Classification (Part 1). Upon satisfactory assessment under 1-1-A3/5.5 (PQA) of the A

29、BS Rules for Conditions of Classification (Part 1), turbochargers produced in those facilities will not require a Surveyors attendance at the tests and inspections indicated in 4-2-2/11.3.1ii). Such tests and inspections are to be carried out by the manufacturer whose quality control documents will

30、be accepted. Certification of each turbocharger will be based on verification of approval of the design and on continued effectiveness of the quality assurance system. See 1-1-A3/5.7.1(a) of the ABS Rules for Conditions of Classification (Part 1). Audits under PQA are to include: Chemical compositio

31、n of material for the rotating parts Mechanical properties of the material of a representative specimen for the rotating parts and the casing UT and crack detection of rotating parts Dimensional inspection of rotating parts Rotor balancing Hydrostatic pressure testing Overspeed testing. 11.3.2(c) Ty

32、pe Approval Program. Turbocharger types which have their designs approved in accordance with 4-2-2/11.3.2(a) and the quality assurance system of their manufacturing facilities approved in accordance with 4-2-2/11.3.2(b) will be deemed Type Approved and will be eligible for listing on the ABS website

33、 as Type Approved Product. 10 ABSGUIDE FOR BUILDING AND CLASSING INTERNATIONAL NAVAL SHIPS .2017 Notice No. 1 July 2017 PART 4 VESSEL SYSTEMS AND MACHINERY CHAPTER 3 PROPULSION AND MANEUVERING MACHINERY SECTION 4 STEERING GEARS 13 Control Systems 13.1 General (Add new Subparagraph 4-3-4/13.1.9, as f

34、ollows:) 13.1.9 System Response Under Failure (1 July 2017) The failures (as listed, but not limited to those items in 4-3-4/Table 1) likely to cause uncontrolled movements of rudder are to be clearly identified. In the event of detection of such failure, the rudder should stop in the current positi

35、on. Alternatively, the rudder may be set to return to the midship/neutral position. Failure Mode and Effect Analysis methodology may be used to identify the failures. (Revise 4-3-4/Table 1, as follows:) TABLE 1 Steering Gear Instrumentation (1 July 2017) Monitored Parameters Display/Alarm Location a

36、) Rudder angle indicator (1)Display Navigation bridge Steering gear compartment b) Power unit motor running Display Navigation bridge Engine room control station c) Power unit power supply failure Alarm Navigation bridge Engine room control station d) Power unit motor overload (2)Alarm Navigation br

37、idge Engine room control station e) Power unit motor phase failure (2), (3)Alarm Navigation bridge Engine room control station f) Control power failure Alarm Navigation bridge Engine room control station g) (1 July 2017) Hydraulic oil reservoir low level (2)Alarm Navigation bridge Engine room contro

38、l station h) Hydraulic lock (4)Alarm Navigation bridge i) Auto-pilot running (5)Display Navigation bridge j) Auto-pilot failure (5)Alarm Navigation bridge k) Steering mode (autopilot/manual) indication Display Navigation bridge l) Automatic autopilot (5)override failure Alarm Navigation bridge m) Au

39、tomatic autopilot (5)override activated Alarm Navigation bridge n) Loop failures (6)Alarm Navigation bridge o) Computer-based system failures (7)Alarm Navigation bridge p) (1 July 2017) Earth fault on AC and DC circuits Alarm Navigation bridge q) (1 July 2017) Deviation between rudder order and feed

40、back Alarm Navigation bridge (Notes remain unchanged.) ABSGUIDE FOR BUILDING AND CLASSING INTERNATIONAL NAVAL SHIPS .2017 11 Notice No. 1 July 2017 PART 4 VESSEL SYSTEMS AND MACHINERY CHAPTER 3 PROPULSION AND MANEUVERING MACHINERY SECTION 5 THRUSTERS 1 General 1.1 Application (1 July 2017) The provi

41、sions of this Section apply to maneuvering thrusters not intended to assist in propulsion, and to azimuthal and non-azimuthal thrusters (and to alternative propulsion and steering systems without a rudder, as applicable) intended for propulsion, maneuvering or dynamic positioning, or a combination o

42、f these duties. Maneuvering thrusters intended to assist maneuvering and dynamic positioning thrusters, where fitted, may, at the request of the owners, be certified in accordance with the provisions of this section. In such cases, appropriate class notations, as indicated in 4-3-5/1.3, will be assi

43、gned upon verification of compliance with corresponding provisions of this section. Thrusters intended for propulsion with or without combined duties for assisting in maneuvering or dynamic positioning are to comply with appropriate provisions of this section in association with other relevant provi

44、sions of Part 4, Chapter 3. Thruster types not provided for in this section, such as cycloidal propellers, pump or water-jet type thrusters, will be considered, based on the manufacturers submittal on design and engineering analyses. Thrusters are to be constructed with sufficient strength, capacity

45、 and the necessary supporting systems to provide reliable propulsion and steering to the vessel in all operating conditions. Special consideration will be given to the suitability of any essential component which is not duplicated. For a vessel fitted with multiple steering systems, each steering sy

46、stem is to be so arranged that the failure of one of them will not render the other one inoperative. Each of the steering systems is equipped with its own dedicated steering gear, provided that each of the steering systems is fulfilling the requirements for main steering gear (as given in 4-3-5/5.12

47、.1) and each of the steering systems is provided with an additional function for positioning and locking the failed steering system in a neutral position after a failure of its own power unit(s) and actuator(s). 1.5 Definitions (Add new Subparagraph 4-3-5/1.5.6, as follows:) 1.5.6 Steering System (1

48、 July 2017) “Steering system” is a vessels directional control system, including main steering gear, auxiliary steering gear, steering gear control system and rudder, if any. 12 ABSGUIDE FOR BUILDING AND CLASSING INTERNATIONAL NAVAL SHIPS .2017 Notice No. 1 July 2017 5 Design 5.12 Arrangements (1 Ju

49、ly 2016) 5.12.2 Auxiliary Steering Gear Arrangements (Revise Item 4-3-5/5.12.2(b), as follows:) 5.12.2(b) In a vessel fitted with multiple steering systems, such as but not limited to azimuthing thrusters or water jet propulsion systems, an auxiliary steering gear need not be fitted, provided that: i) For a passenger vessel, each of the steering systems, is capable of satisfying the requirements in 4-3-5/5.12.1ii) while any one of the power units is out of operation; ii) For a cargo v

copyright@ 2008-2019 麦多课文库(www.mydoc123.com)网站版权所有
备案/许可证编号:苏ICP备17064731号-1