AASHTO M 170M-2017 Standard Specification for Reinforced Concrete Culvert Storm Drain and Sewer Pipe [Metric].pdf

1、Standard Specification for Reinforced Concrete Culvert, Storm Drain, and Sewer Pipe Metric AASHTO Designation: M 170M-171 Technical Section: 4a, Concrete Drainage Structures Release: Group 2 (June 2017) ASTM Designation: C76M-16 American Association of State Highway and Transportation Officials 444

2、North Capitol Street N.W., Suite 249 Washington, D.C. 20001 TS-4a M 170M-1 AASHTO Standard Specification for Reinforced Concrete Culvert, Storm Drain, and Sewer Pipe Metric AASHTO Designation: M 170M-171Technical Section: 4a, Concrete Drainage Structures Release: Group 2 (June 2017) ASTM Designation

3、: C76M-16 1. SCOPE 1.1. This specification covers reinforced concrete pipe intended to be used for the conveyance of sewage, industrial wastes, and storm water, and for the construction of culverts. 1.2. This specification is the metric counterpart of M 170. Note 1This specification is a manufacturi

4、ng and purchase specification only, and does not include requirements for bedding, backfill, or the relationship between field load condition and the strength classification of pipe. However, experience has shown that the successful performance of this product depends on the proper selection of the

5、class of pipe, type of bedding and backfill, controlled manufacture in the plant, and care that installation conforms to the construction specifications. Owners of the reinforced concrete pipe specified herein are cautioned that they must correlate the field requirements with the class of pipe speci

6、fied and provide inspection at the construction site. Note 2Attention is called to the specification for reinforced concrete D-load culvert, storm drain, and sewer pipe (M 242M/M 242). 2. REFERENCED DOCUMENTS 2.1. AASHTO Standards: M 6, Fine Aggregate for Hydraulic Cement Concrete M 31M/M 31, Deform

7、ed and Plain Carbon and Low-Alloy Steel Bars for Concrete Reinforcement M 32M/M 32, Steel Wire, Plain, for Concrete Reinforcement M 55M/M 55, Steel Welded Wire Reinforcement, Plain, for Concrete M 80, Coarse Aggregate for Hydraulic Cement Concrete M 85, Portland Cement M 86M/M 86, Nonreinforced Conc

8、rete Sewer, Storm Drain, and Culvert Pipe M 154M/M 154, Air-Entraining Admixtures for Concrete M 157, Ready-Mixed Concrete M 170, Reinforced Concrete Culvert, Storm Drain, and Sewer Pipe M 194M/M 194, Chemical Admixtures for Concrete M 221M/M 221, Steel Welded Wire Reinforcement, Deformed, for Concr

9、ete 2017 by the American Association of State Highway and Transportation Officials.All rights reserved. Duplication is a violation of applicable law.TS-4a M 170M-2 AASHTO M 225M/M 225, Steel Wire, Deformed, for Concrete Reinforcement M 240M/M 240, Blended Hydraulic Cement M 242M/M 242, Reinforced Co

10、ncrete D-Load Culvert, Storm Drain, and Sewer Pipe M 262, Concrete Pipe and Related Products M 295, Coal Fly Ash and Raw or Calcined Natural Pozzolan for Use in Concrete M 302, Slag Cement for Use in Concrete and Mortars T 280, Concrete Pipe, Manhole Sections, or Tile 2.2. ASTM Standards: A36/A36M,

11、Standard Specification for Carbon Structural Steel A706/A706M, Standard Specification for Deformed and Plain Low-Alloy Steel Bars for Concrete Reinforcement C309-03, Standard Specification for Liquid Membrane-Forming Compounds for Curing Concrete C1017/C1017M, Standard Specification for Chemical Adm

12、ixtures for Use in Producing Flowing Concrete C1116/C1116M, Standard Specification for Fiber-Reinforced Concrete 3. TERMINOLOGY 3.1. DefinitionsFor definitions of terms relating to concrete pipe, see M 262. 4. CLASSIFICATION 4.1. Pipe manufactured in accordance with this specification shall be of fi

13、ve classes identified as Class I, Class II, Class III, Class IV, and Class V. The corresponding strength requirements are prescribed in Tables 1 to 5. 2017 by the American Association of State Highway and Transportation Officials.All rights reserved. Duplication is a violation of applicable law.TS-4

14、a M 170M-3 AASHTO Table 1Design Requirements for Class I Reinforced Concrete Pipea Internal Designated Diameter, mm Reinforcement, cm2/Linear m of Pipe Wall Wall A Wall B Concrete Strength, 27.6 MPa Concrete Strength, 27.6 MPa Wall Thickness, mm Circular ReinforcementbElliptical ReinforcementcWall T

15、hickness, mm Circular ReinforcementbElliptical ReinforcementcInner Cage Outer Cage Inner Cage Outer Cage 1500 125 5.3 3.2 5.9 150 4.4 2.6 4.9 1650 138 6.4 3.8 7.0 163 5.3 3.2 5.9 1800 150 7.4 4.4 8.3 175 6.1 3.7 6.8 1950 163 8.5 5.1 9.3 188 6.8 4.1 7.6 2100 175 9.5 5.7 10.6 200 7.8 4.7 8.7 2250 188

16、10.4 6.2 11.4 213 8.7 5.2 9.7 2400 200 11.4 6.8 12.7 225 9.7 5.8 10.8 Concrete Strength, 34.5 MPa Concrete Strength, 34.5 MPa 2250 213 13.3 8.0 Inner Circular Plus Elliptical 5.3 8.0 238 11.4 6.8 Inner Circular Plus Elliptical 4.6 6.8 2700 225 14.4 8.6 Inner Circular Plus Elliptical 5.8 8.6 250 12.9

17、 7.7 Inner Circular Plus Elliptical 5.2 7.7 2850 a a 3000 a a 3150 a a 3300 a a 3450 a a 3600 a a aFor modified or special designs, see Section 7.2 or, with the permission of the owner, utilize the provision of M 242M/M 242. Steel areas may be interpolated between those shown for variations in diame

18、ter, loading, or wall thickness. Pipe more than 2400 mm in diameter shall have two circular cages or an inner circular cage plus one elliptical cage. bAs an alternative to designs requiring both inner and outer circular cages, the reinforcement may be positioned and proportioned in one of the follow

19、ing manners: (1) an inner circular cage plus an elliptical cage such that the area of the elliptical cage shall not be less than that specified for the outer cage in the table, and the total area of the inner circular cage plus the elliptical cage shall not be less than that specified for the inner

20、cage in the table; (2) an inner and outer cage plus quadrant mats in accordance with Figure 1; or (3) an inner and outer cage plus an elliptical cage in accordance with Figure 2. cElliptical and quadrant steel must be held in place by means of holding rods, chairs, or other positive means throughout

21、 the entire casting operation. Note: See Section 5 for basis of acceptance specified by the owner. The strength test requirements in newtons per linear meter of pipe under the three-edge-bearing method are listed below as the D-load (test load expressed in newtons per linear meter per millimeter of

22、diameter) to produce the 0.3-mm crack and the ultimate load multiplied by the internal diameter of the pipe in millimeters. For acceptance testing requirements, see Section 11.3.1. D-load to produce a 0.3-mm crack 40.0 D-load to produce the ultimate load 60.0 2017 by the American Association of Stat

23、e Highway and Transportation Officials.All rights reserved. Duplication is a violation of applicable law.TS-4a M 170M-4 AASHTO Table 2Design Requirements for Class II Reinforced Concrete PipeaInternal Designated Diameter, mm Reinforcement, cm2/Linear m of Pipe Wall Wall A Wall B Wall C Concrete Stre

24、ngth, 27.6 MPa Concrete Strength, 27.6 MPa Concrete Strength, 27.6 MPa Wall Thickness, mm Circular ReinforcementbElliptical ReinforcementcWall Thickness, mm Circular ReinforcementbElliptical ReinforcementcWall Thickness, mm Circular ReinforcementbElliptical ReinforcementcInner Cage Outer Cage Inner

25、Cage Outer Cage Inner Cage Outer Cage 300 44 1.5d 50 1.5d 69 1.5d 375 47 1.5d 57 1.5d 75 1.5d 450 50 1.5d 1.5 63 1.5d 1.5d82 1.5d 1.5d525 57 2.5 2.1 69 1.5d 1.5d88 1.5d 1.5d600 63 2.8 2.3 75 1.5d 1.5d94 1.5d 1.5d675 66 3.2 2.8 82 2.8 2.3 100 1.5d 1.5d750 69 3.2 3.0 88 3.0 2.5 106 1.5d 1.5d825 72 3.4

26、 3.2 94 3.2 2.8 113 1.5d 1.5d900 75 3.0 1.8 3.2 100e2.5 1.5 2.8 119e1.5 1.5 1.7 1050 88 3.4 2.0 3.8 113 3.2 1.9 3.6 132 2.1 1.5 2.3 1200 100 4.5 2.7 4.9 125 3.8 2.3 4.2 144 3.0 1.8 3.2 1350 113 5.3 3.2 5.9 138 4.7 2.8 5.1 157 3.6 2.2 4.0 1500 125 6.4 3.8 7.0 150 5.3 3.2 5.9 169 4.7 2.8 5.1 1650 138

27、7.4 4.4 8.3 163 6.6 4.0 7.2 182 5.3 3.2 5.9 1800 150 8.7 5.2 9.5 175 7.4 4.4 8.3 194 6.4 3.8 7.0 1950 163 9.7 5.8 10.8 188 8.5 5.1 9.3 207 7.4 4.4 8.3 2100 175 10.8 6.5 12.1 200 9.7 5.8 10.8 219 8.7 5.2 9.7 2250 188 12.1 7.3 13.3 213 10.8 6.5 12.1 232 10.2 6.1 11.2 2400 200 13.1 7.9 14.6 225 12.1 7.

28、3 13.3 244 11.6 7.0 12.9 Concrete Strength, 34.5 MPa 2550 213 16.1 9.7 Inner Circular Plus Elliptical 6.4 9.7 238 14.4 8.6 Inner Circular Plus Elliptical 5.8 8.6 257 13.1 7.9 Inner Circular Plus Elliptical 5.2 7.9 2700 225 18.0 10.8 Inner Circular Plus Elliptical 7.2 10.8 250 16.1 9.7 Inner Circular

29、 Plus Elliptical 6.4 9.7 269 14.8 8.9 Inner Circular Plus Elliptical 5.9 8.9 2850 a a a 3000 a a a 3150 a a a 3300 a a a 3450 a a a 3600 a a a Continued on next page. 2017 by the American Association of State Highway and Transportation Officials.All rights reserved. Duplication is a violation of app

30、licable law.TS-4a M 170M-5 AASHTO Table 2Design Requirements for Class II Reinforced Concrete Pipea(Continued) a For modified or special designs, see Section 7.2 or, with the permission of the owner, utilize the provision of M 242M/M 242. Steel areas may be interpolated between those shown for varia

31、tions in diameter, loading, or wall thickness. Pipe more than 2400 mm in diameter shall have two circular cages or an inner circular cage plus one elliptical cage. bAs an alternative to designs requiring both inner and outer circular cages, the reinforcement may be positioned and proportioned in one

32、 of the following manners: (1) an inner circular cage plus an elliptical cage such that the area of the elliptical cage shall not be less than that specified for the outer cage in the table, and the total area of the inner circular cage plus the elliptical cage shall not be less than that specified

33、for the inner cage in the table; (2) an inner and outer cage plus quadrant mats in accordance with Figure 1; or (3) an inner and outer cage plus an elliptical cage in accordance with Figure 2. cElliptical and quadrant steel must be held in place by means of holding rods, chairs, or other positive me

34、ans through the entire casting operation. dFor these classes and size, the minimum practical steel reinforcement is specified. The specified ultimate strength of nonreinforced pipe is greater than the minimum specified strength for the equivalent diameters (see M 86M/M 86). eAs an alternative, singl

35、e-cage reinforcement may be used. The reinforcement area in square centimeters per linear meter shall be 4.2 for Wall B and 3.4 for Wall C. Note: See Section 5 for basis of acceptance specified by the owner. The strength test requirements in newtons per linear meter of pipe under the three-edge-bear

36、ing method are listed below as the D-load (test load expressed in newtons per linear meter per millimeter of diameter) to produce the 0.3-mm crack and the ultimate load multiplied by the internal diameter of the pipe in millimeters. For acceptance testing requirements, see Section 11.3.1. D-load to

37、produce a 0.3-mm crack 50.0 D-load to produce the ultimate load 75.0 2017 by the American Association of State Highway and Transportation Officials.All rights reserved. Duplication is a violation of applicable law.TS-4a M 170M-6 AASHTO Table 3Design Requirements for Class III Reinforced Concrete Pip

38、eaInternal Designated Diameter, mm Reinforcement, cm2/Linear m of Pipe Wall Wall A Wall B Wall C Concrete Strength, 27.6 MPa Concrete Strength, 27.6 MPa Concrete Strength, 27.6 MPa Wall Thickness, mm Circular ReinforcementbElliptical ReinforcementcWall Thickness, mm Circular ReinforcementbElliptical

39、 ReinforcementcWall Thickness, mm Circular ReinforcementbElliptical ReinforcementcInner Cage Outer Cage Inner Cage Outer Cage Inner Cage Outer Cage 300 44 1.5d 50 1.5d 69 1.5d 375 47 1.5d 57 1.5d 75 1.5d 450 50 1.5d 1.5d63 1.5d 1.5d82 1.5d 1.5d525 57 3.0 2.3 69 1.5d 1.5d88 1.5d 1.5d600 63 3.6 3.0 75

40、 1.5d 1.5d94 1.5 1.5d675 66 3.8 3.4 82 3.4 3.0 100 1.7 1.5d750 69 4.0 3.8 88 3.8 3.2 107 2.1 1.7 825 72 4.4 4.2 94 4.2 3.6 113 2.5 2.1 900 75 4.4 2.6 4.7 100e3.6 2.2 4.0 119e1.7 1.5 1.9 1050 88 5.3 3.2 5.9 113 4.4 2.6 4.9 132 2.5 1.5 2.8 1200 100 6.8 4.1 7.4 125 5.1 3.1 5.7 144 3.4 2.0 3.8 1350 113

41、8.0 4.8 8.9 138 6.1 3.7 6.8 157 4.4 2.6 4.9 1500 125 9.3 5.6 10.4 150 7.2 4.3 8.0 169 5.3 3.2 5.9 1650 138 10.6 6.4 11.6 163 9.1 5.5 9.7 182 6.6 4.0 7.2 1800 150 12.1 7.3 13.3 175 10.4 6.2 11.4 194 7.6 4.6 8.5 Concrete Strength, 34.5 MPa 1950 163 13.5 8.1 15.0 188 12.1 7.3 13.3 207 8.9 5.3 9.9 2100

42、175 15.2 9.1 16.9 200 13.5 8.1 15.0 219 10.6 6.4 11.9 Concrete Strength, 34.5 MPa Concrete Strength, 34.5 MPa 2250 188 17.1 10.3 19.1 213 14.6 8.8 16.3 232 12.5 7.5 14.0 2400 200 19.7 11.8 21.8 225 16.1 9.7 17.8 244 14.8 8.9 Inner Circular Plus Elliptical 5.9 8.9 2550 213 21.8 13.1 Inner Circular Pl

43、us Elliptical 8.7 13.1 238 19.1 11.5 Inner Circular Plus Elliptical 7.6 11.5 257 17.6 10.6 Inner Circular Plus Elliptical 7.0 10.6 Continued on next page. 2017 by the American Association of State Highway and Transportation Officials.All rights reserved. Duplication is a violation of applicable law.

44、TS-4a M 170M-7 AASHTO Table 3Design Requirements for Class III Reinforced Concrete Pipea(Continued) Internal Designated Diameter, mm Reinforcement, cm2/Linear m of Pipe Wall Wall A Wall B Wall C Concrete Strength, 27.6 MPa Concrete Strength, 27.6 MPa Concrete Strength, 27.6 MPa Wall Thickness, mm Ci

45、rcular ReinforcementbElliptical ReinforcementcWall Thickness, mm Circular ReinforcementbElliptical ReinforcementcWall Thickness, mm Circular ReinforcementbElliptical ReinforcementcInner Cage Outer Cage Inner Cage Outer Cage Inner Cage Outer Cage 2700 225 25.8 15.5 Inner Circular Plus Elliptical 10.3

46、 15.5 250 22.9 13.7 Inner Circular Plus Elliptical 9.2 13.7 269 21.0 12.6 Inner Circular Plus Elliptical 8.4 12.6 2850 a a a 3000 a a a 3150 a a a 3300 a a a 3450 a a a 3600 a a a aFor modified or special designs, see Section 7.2 or with the permission of the owner utilize the provision of M 242M/M

47、242. Steel areas may be interpolated between those shown for variations in diameter, loading, or wall thickness. Pipe more than 2400 mm in diameter shall have two circular cages or an inner circular cage plus one elliptical cage. bAs an alternative to designs requiring both inner and outer circular cages, the reinforcement may be positioned and proportioned in one of the following manners: (1) an inner circular cage plus an elliptical cage such that the area of the elliptical cage shall not be less than that specified f