ABMA 104-2016 Rolling bearings - Thrust bearings - Boundary dimensions general plan.pdf

1、 Rolling bearings Thrust bearings Boundary dimensions, general plan ANSI/ABMA/ISO 104-2016 Sponsor American Bearing Manufacturers Association ANSI/ABMA/ISO 104-2016 (Identical Adoption of ISO 104:2015) Copyright American Bearing Manufacturers Association, Inc. Neither part of the printed publication

2、, nor any part of the electronic tile may be reproduced or transmitted in any form, including transmittal by e-mail, by file transfer protocol (FTP), or by being made part of a network-accessible system, without the prior written permission of the copyright owner. ABMA FOREWORD (This foreword is not

3、 part of ANSI/ABMA/ISO 104-2016.) IS0 (the International Organization for Standardization) is a worldwide federation of national standards bodies (IS0 member bodies). The work of developing International Standards is carried out through IS0 technical committees. Every member body interested in a sub

4、ject for which a technical committee has been authorized has the right to be represented on that committee. International organizations, governmental and non-governmental, in liaison with ISO, also take part in the work. The text is approved as an International Standard if a two-thirds majority of t

5、he P (participating)-members of the TC/SC are in favor and not more than one-quarter of the total number of votes cast are negative. International Standard 104:2015 was prepared by Technical Committee ISO/TC 4, Rolling Bearings. This standard was processed and approved for submittal to ANSI for nati

6、onal adoption by Accredited Standards Committee B3. Committee approval of the national adoption of this standard does not necessarily mean that all committee members voted for its adoption. Suggestions for the improvement of this standard gained through experience with its use will be welcomed. Thes

7、e suggestions should be sent to: ASC B3 Secretariat American Bearing Manufacturers Association 2025 M Street, N.W., Suite 800 Washington, DC 20036 ISO 2015Rolling bearings Thrust bearings Boundary dimensions, general planRoulements Butes Dimensions dencombrement, plan gnralINTERNATIONAL STANDARDISO1

8、04Fourth edition2015-09-15Reference numberISO 104:2015(E)Copyright by ISO. Reproduced by ANSI with permission of and under license from ISO. Licensed to committee members for further standardization only. Downloaded 9/16/2015 10:39 AM. Not for additional sale or distribution.ISO 104:2015(E)ii ISO 20

9、15 All rights reservedCOPYRIGHT PROTECTED DOCUMENT ISO 2015, Published in SwitzerlandAll rights reserved. Unless otherwise specified, no part of this publication may be reproduced or utilized otherwise in any form or by any means, electronic or mechanical, including photocopying, or posting on the i

10、nternet or an intranet, without prior written permission. Permission can be requested from either ISO at the address below or ISOs member body in the country of the requester.ISO copyright officeCh. de Blandonnet 8 CP 401CH-1214 Vernier, Geneva, SwitzerlandTel. +41 22 749 01 11Fax +41 22 749 09 47co

11、pyrightiso.orgwww.iso.orgCopyright by ISO. Reproduced by ANSI with permission of and under license from ISO. Licensed to committee members for further standardization only. Downloaded 9/16/2015 10:39 AM. Not for additional sale or distribution.ISO 104:2015(E)Foreword iv1 Scope . 12 Normative referen

12、ces 13 Terms and definitions . 14 Symbols 15 Boundary dimensions . 35.1 General . 35.2 Single-direction thrust bearings with flat back faces 35.3 Double-direction thrust bearings with flat back faces 16Annex A (informative) Guidelines for the extension of this International Standard for single-direc

13、tion thrust bearings .20Bibliography .22 ISO 2015 All rights reserved iiiContents PageCopyright by ISO. Reproduced by ANSI with permission of and under license from ISO. Licensed to committee members for further standardization only. Downloaded 9/16/2015 10:39 AM. Not for additional sale or distribu

14、tion.ISO 104:2015(E)ForewordISO (the International Organization for Standardization) is a worldwide federation of national standards bodies (ISO member bodies). The work of preparing International Standards is normally carried out through ISO technical committees. Each member body interested in a su

15、bject for which a technical committee has been established has the right to be represented on that committee. International organizations, governmental and non-governmental, in liaison with ISO, also take part in the work. ISO collaborates closely with the International Electrotechnical Commission (

16、IEC) on all matters of electrotechnical standardization.The procedures used to develop this document and those intended for its further maintenance are described in the ISO/IEC Directives, Part 1. In particular the different approval criteria needed for the different types of ISO documents should be

17、 noted. This document was drafted in accordance with the editorial rules of the ISO/IEC Directives, Part 2 (see www.iso.org/directives). Attention is drawn to the possibility that some of the elements of this document may be the subject of patent rights. ISO shall not be held responsible for identif

18、ying any or all such patent rights. Details of any patent rights identified during the development of the document will be in the Introduction and/or on the ISO list of patent declarations received (see www.iso.org/patents). Any trade name used in this document is information given for the convenien

19、ce of users and does not constitute an endorsement.For an explanation on the meaning of ISO specific terms and expressions related to conformity assessment, as well as information about ISOs adherence to the WTO principles in the Technical Barriers to Trade (TBT) see the following URL: Foreword - Su

20、pplementary informationThe committee responsible for this document is ISO/TC 4, Rolling bearings.This fourth edition cancels and replaces the third edition (ISO 104:2002), which has been technically revised with changes that are editorial and concern mainly on terminology and format.iv ISO 2015 All

21、rights reservedCopyright by ISO. Reproduced by ANSI with permission of and under license from ISO. Licensed to committee members for further standardization only. Downloaded 9/16/2015 10:39 AM. Not for additional sale or distribution.INTERNATIONAL STANDARD ISO 104:2015(E)Rolling bearings Thrust bear

22、ings Boundary dimensions, general plan1 ScopeThis International Standard specifies preferred boundary dimensions for single-direction and double-direction thrust bearings with flat back faces.In addition, it gives the minimum bore diameters of housing washers and maximum outside diameters of shaft w

23、ashers of bearings in dimension series 11, 12, 13, 14, 22, 23 and 24.Guidelines for the extension of this International Standard for single-direction thrust bearings are given in Annex A.NOTE Boundary dimensions for aligning thrust bearings (none flat back faces) and aligning seat washers are given

24、in ISO 20516.22 Normative referencesThe following documents, in whole or in part, are normatively referenced in this document and are indispensable for its application. For dated references, only the edition cited applies. For undated references, the latest edition of the referenced document (includ

25、ing any amendments) applies.ISO 582, Rolling bearings Chamfer dimensions Maximum valuesISO 5593, Rolling bearings VocabularyISO 15241, Rolling bearings Symbols for physical quantities3 Terms and definitionsFor the purposes of this document, the terms and definitions given in ISO 5593 and the followi

26、ng apply.3.1single-direction thrust bearing with flat back facesthrust rolling bearing with flat back faces intended to support axial load in one direction only3.2double-direction thrust bearing with flat back facesthrust rolling bearing with flat back faces intended to support axial load in both di

27、rections3.3central shaft washercentral washer which is intended to be mounted on a shaftSOURCE: ISO 20516:2007, 3.54 SymbolsFor the purposes of this International Standard, the symbols given in ISO 15241 and the following apply. ISO 2015 All rights reserved 1Copyright by ISO. Reproduced by ANSI with

28、 permission of and under license from ISO. Licensed to committee members for further standardization only. Downloaded 9/16/2015 10:39 AM. Not for additional sale or distribution.ISO 104:2015(E)The symbols shown in Figures 1 and 2 and the values given in Tables 1 to 9 denote nominal dimensions, unles

29、s specified otherwise.B height of central shaft washerD outside diameter of housing washerD1bore diameter of housing washerD1s minsmallest single bore diameter of housing washerd bore diameter of shaft washer, single-direction thrust bearing with flat back facesd1outside diameter of shaft washer, si

30、ngle-direction thrust bearing with flat back facesd1s maxlargest single outside diameter of shaft washerd2bore diameter of central shaft washer, double-direction thrust bearing with flat back facesd3outside diameter of central shaft washer, double-direction thrust bearing with flat back facesd3s max

31、largest single outside diameter of central shaft washerr back face chamfer dimension of shaft washer and housing washerrs minsmallest single back face chamfer dimension of shaft washer and housing washerr1face chamfer dimension of central shaft washerr1s minsmallest single face chamfer dimension of

32、central shaft washerT bearing height, single-direction thrust bearing with flat back facesT1bearing height, double-direction thrust bearing with flat back facesFigure 1 Single-direction thrust bearing with flat back faces2 ISO 2015 All rights reservedCopyright by ISO. Reproduced by ANSI with permiss

33、ion of and under license from ISO. Licensed to committee members for further standardization only. Downloaded 9/16/2015 10:39 AM. Not for additional sale or distribution.ISO 104:2015(E)Figure 2 Double-direction thrust bearing with flat back faces5 Boundary dimensions5.1 GeneralThe corresponding larg

34、est single chamfer dimensions to the rs mindimensions in Tables 1 to 9 and r1s mindimensions in Tables 7 to 9 are given in ISO 582.Chamfer dimensions r and r1apply only at the corners indicated in Figures 1 and 2. No dimensions are given for other corners; however, they should not be sharp.5.2 Singl

35、e-direction thrust bearings with flat back facesDimensions for single-direction thrust bearings with flat back faces are given in Tables 1 to 6.Table 1 Single-direction thrust bearings Diameter series 0Dimensions in millimetresDimension seriesd D rs min70 90 10T4 12 0,3 4 66 16 0,3 5 78 18 0,3 5 710

36、 20 0,3 5 712 22 0,3 5 715 26 0,3 5 717 28 0,3 5 720 32 0,3 6 8 ISO 2015 All rights reserved 3Copyright by ISO. Reproduced by ANSI with permission of and under license from ISO. Licensed to committee members for further standardization only. Downloaded 9/16/2015 10:39 AM. Not for additional sale or

37、distribution.ISO 104:2015(E)Dimension seriesd D rs min70 90 10T25 37 0,3 6 830 42 0,3 6 835 47 0,3 6 840 52 0,3 6 945 60 0,3 7 1050 65 0,3 7 1055 70 0,3 7 1060 75 0,3 7 1065 80 0,3 7 1070 85 0,3 7 1075 90 0,3 7 1080 95 0,3 7 1085 100 0,3 7 1090 105 0,3 7 10100 120 0,6 9 14110 130 0,6 9 14120 140 0,6

38、 9 14130 150 0,6 9 14140 160 0,6 9 14150 170 0,6 9 14160 180 0,6 9 14170 190 0,6 9 14180 200 0,6 9 14190 215 1 11 17200 225 1 11 17220 250 1 14 22240 270 1 14 22260 290 1 14 22280 310 1 14 22300 340 1 18 24 30320 360 1 18 24 30340 380 1 18 24 30Table 1 (continued)4 ISO 2015 All rights reservedCopyri

39、ght by ISO. Reproduced by ANSI with permission of and under license from ISO. Licensed to committee members for further standardization only. Downloaded 9/16/2015 10:39 AM. Not for additional sale or distribution.ISO 104:2015(E)Dimension seriesd D rs min70 90 10T360 400 1 18 24 30380 420 1 18 24 304

40、00 440 1 18 24 30420 460 1 18 24 30440 480 1 18 24 30460 500 1 18 24 30480 520 1 18 24 30500 540 1 18 24 30530 580 1,1 23 30 38560 610 1,1 23 30 38600 650 1,1 23 30 38630 680 1,1 23 30 38670 730 1,5 27 36 45710 780 1,5 32 42 53750 820 1,5 32 42 53800 870 1,5 32 42 53850 920 1,5 32 42 53900 980 2 36

41、48 63950 1 030 2 36 48 631 000 1 090 2,1 41 54 701 060 1 150 2,1 41 54 701 120 1 220 2,1 45 60 801 180 1 280 2,1 45 60 801 250 1 360 3 50 67 851 320 1 440 3 951 400 1 520 3 951 500 1 630 4 1051 600 1 730 4 1051 700 1 840 4 1121 800 1 950 4 1201 900 2 060 5 1302 000 2 160 5 1302 120 2 300 5 140Table

42、1 (continued) ISO 2015 All rights reserved 5Copyright by ISO. Reproduced by ANSI with permission of and under license from ISO. Licensed to committee members for further standardization only. Downloaded 9/16/2015 10:39 AM. Not for additional sale or distribution.ISO 104:2015(E)Dimension seriesd D rs

43、 min70 90 10T2 240 2 430 5 1502 360 2 550 5 1502 500 2 700 5 160Table 2 Single-direction thrust bearings Diameter series 1Dimensions in millimetresDimension seriesd D rs min71 91 11T d1s maxD1s min10 24 0,3 6 9 24 1112 26 0,3 6 9 26 1315 28 0,3 6 9 28 1617 30 0,3 6 9 30 1820 35 0,3 7 10 35 2125 42 0

44、,6 8 11 42 2630 47 0,6 8 11 47 3235 52 0,6 8 12 52 3740 60 0,6 9 13 60 4245 65 0,6 9 14 65 4750 70 0,6 9 14 70 5255 78 0,6 10 16 78 5760 85 1 11 17 85 6265 90 1 11 18 90 6770 95 1 11 18 95 7275 100 1 11 19 100 7780 105 1 11 19 105 8285 110 1 11 19 110 8790 120 1 14 22 120 92100 135 1 16 21 25 135 10

45、2110 145 1 16 21 25 145 112120 155 1 16 21 25 155 122130 170 1 18 24 30 170 132140 180 1 18 24 31 178 142150 190 1 18 24 31 188 152Table 1 (continued)6 ISO 2015 All rights reservedCopyright by ISO. Reproduced by ANSI with permission of and under license from ISO. Licensed to committee members for fu

46、rther standardization only. Downloaded 9/16/2015 10:39 AM. Not for additional sale or distribution.ISO 104:2015(E)Dimension seriesd D rs min71 91 11T d1s maxD1s min160 200 1 18 24 31 198 162170 215 1,1 20 27 34 213 172180 225 1,1 20 27 34 222 183190 240 1,1 23 30 37 237 193200 250 1,1 23 30 37 247 2

47、03220 270 1,1 23 30 37 267 223240 300 1,5 27 36 45 297 243260 320 1,5 27 36 45 317 263280 350 1,5 32 42 53 347 283300 380 2 36 48 62 376 304320 400 2 36 48 63 396 324340 420 2 36 48 64 416 344360 440 2 36 48 65 436 364380 460 2 36 48 65 456 384400 480 2 36 48 65 476 404420 500 2 36 48 65 495 424440

48、540 2,1 45 60 80 535 444460 560 2,1 45 60 80 555 464480 580 2,1 45 60 80 575 484500 600 2,1 45 60 80 595 504530 640 3 50 67 85 635 534560 670 3 50 67 85 665 564600 710 3 50 67 85 705 604630 750 3 54 73 95 745 634670 800 4 58 78 105 795 674710 850 4 63 85 112 845 714750 900 4 67 90 120 895 755800 950

49、 4 67 90 120 945 805850 1 000 4 67 90 120 995 855900 1 060 5 73 95 130 1 055 905950 1 120 5 78 103 135 1 115 9551 000 1 180 5 82 109 140 1 175 1 005Table 2 (continued) ISO 2015 All rights reserved 7Copyright by ISO. Reproduced by ANSI with permission of and under license from ISO. Licensed to committee members for further standardization only. Down