AECMA PREN 2076-3-1987 Aerospace Series Aluminium and Magnesium Alloy Ingots and Castings - Technical Specification - Part 3 - Pre-Production and Production Castings Edition 1《航空和航.pdf

1、A.E.C.M.A. STANDARD NORME A.E.C.M.A. A.E.C.M.A. NORM Approved by COMITE DE NORMALISATION of A.Eet2.M.A. 1987-02-01 prEN2076 Part 3 Edition 1 February 1987 The equivalent versions in French and German languages can be supplied by B.N.A.E., 8, rue Moreau-Vauthier 92100 BOULOGNE-BILLANCOURT - FRANCE. E

2、NGLISH VERSION Aerospace series Aluminium and magnesium alloy ingots and castings - Technical specification - Part 3 - Pre-production and production castings Srie arospatiale Luft- und Raumfahrt Lingots et pices moules en alliages daluminium et de magnsium - Spcification technique - Partie 3 - Pices

3、 types et pices de serie Blcke und Gustcke aus Aluminium- und Magnesiumlegierungen - Technische Lieferbedingungen - Teil 3 - Ausfallmuster und Seriengustcke - This industrial standard for the aerospace sector has been drawn up under the responsibility of AECMA (Association Europenne des Constructeur

4、s de Matriel Arospatiat). It is published on yellow paper in three equivalent versions (English, French, German). It will be submitted to CEN (European Commitree for Standardization) as a draft European Standad. * Copyright Association Europeene des Constructeurs de Materiel Aerospatial Provided by

5、IHS under license with AECMANot for ResaleNo reproduction or networking permitted without license from IHS-,-,-AECMA PREN207b-03 87 LOL23LL 0007658 2 mi prEN2076-3 Page 2 Contents 1 2 References 3 Casting deve1 opment 4 Pre-production castings 5 Manufacture of production castings Scope and field of

6、application 6 7 Weld repair Inspection and testing of production castings 8 Marking Copyright Association Europeene des Constructeurs de Materiel Aerospatial Provided by IHS under license with AECMANot for ResaleNo reproduction or networking permitted without license from IHS-,-,-AECMA PREN207b-03 7

7、 L0123LL 0007b59 4 - _- prEN2076-3 Page 3 1 Scope and field of application This standard specifies the particular requirements for castings in aluminium and magnesium alloys produced from material complying with EN2076-2. ThSs standard also applies to pre-production castinp intended for the qualific

8、ation of the method of manufacture and inspection. This standard shall be used in conjunction with EN2C76-1. 2 References EN2002-1, Aerospace series - Test methods for metallic maty-ials - Part 1 - Tensile testing at ambient temperature EN2002-7, Aerospace series - Test.qi$thods for metallic materia

9、ls - Part 7 - Hardness tests EN2002-16, Aerospace series - Test methods ffy metallic materials - Part 16 - Dye penetrant testing EN2002-21, Aerospace series - Test methods for metallic mater Is - EN2004-4, Aerospace series - Test methods for aluminium and aluminium alloys - Part 4 - Stress corrosion

10、 test method for hi$ strength al uminium al 1 oy wrought proaucts. Al ternate immersion Part 21 - Radiographic testing of cast components 17 1 EN2076-1, Aerospace series - Aluminium and magnesium alloy ingots and castings - Technical specification - Part 1 - General requirements EN2076-2, Aerospace

11、series - Aluminium and magnesium alloy ingots and castings - Technical specification - Part 2 - Ingots for remelting e i) in preparation Copyright Association Europeene des Constructeurs de Materiel Aerospatial Provided by IHS under license with AECMANot for ResaleNo reproduction or networking permi

12、tted without license from IHS-,-,- I AECMA PREN207b-03 87 pp0L23LL 0007bb0 O W I I prEN2076-3 Page 4 3 Casting deve1 opment It is strongly recommended that the technical representative of the manufacturer be given the opportunity to examine the casting drawing at the initial stages of design and to

13、advise on the optimum design which will facilitate consistent production of acceptable castings. The dimensional tolerances of the castings shall be as aoreed between the purchaser and manufacturer and indicated on the drawing or the inspection schedule. 4 Pre-production castings 4.1 General 4.1.1 T

14、he following requirements shall be specified on the order, drawing and/or inspection schedule in addition to those specified in EN2076-1 : - Number of castings to be examined - Who shall perform the examination -. - - Heat treatment condition - Type and frequency of inspection and testing necessary

15、to evaluate and qualify the manufacturing process (dimensions , mechanical and metallurgical properties, etc.). 4.1.2 The inspection and testing of pre-production castings shall be carried out and the inspection and testing conditions shall be recorded to allow the definition of the optimum techniqu

16、es to be used for production castings. -0 4.1.3 The inspection and tests carried out on pre-production castings shall include those which will be carried out on production castinos, 4.2 Inspection and testing report In addition to the information required by EN2076-1, the inspection and testing repo

17、rt on the pre-production castings shall provide all -technical information to allow evaluation of the quality of these parts, e.g., radiographs, results of dimensional measurements . Copyright Association Europeene des Constructeurs de Materiel Aerospatial Provided by IHS under license with AECMANot

18、 for ResaleNo reproduction or networking permitted without license from IHS-,-,-AECMA PREN2076-03 87 3012313 0007663 2 m prENZ076-3 Page 5 4.3 Acceptance of pre-production castings Nhen al 1 inspection and test results relative to pre-production castings have been reported and considereded as satisf

19、actory by the purchaser and manufacturer, the purchaser shall give his written agreement or order for series production. The inspection schedule and if required the manufacturing schedule shall be agreed between the manufacturer and purchaser. 5 Manufacture of production castings 5.1 At the start of

20、 production (particularly at the start of series production), the manufacturing schedule may be completed to al 1 ow the manufacturer to guarantee the reproducibility of the product with more certainty. All information, no matter how minor, shall be recorded in the manufacturing schedul e. 5.2 When

21、a manufacturing schedule has been agreed, no change in manufacturing method shall be made without the written approval of the purchaser. When such changes are necessary in the case of, for example : a) b) Alterations of pattern, mould material or position of runners and risers, Alteration of the cas

22、ting process, c) Alterations of the heat ti-eatment process, the purchaser shall decide if new pre-production castings shall be manufactured and tested. The manufacturing schedule and the inspectiot schedule shall be modified if necessary. 5.3 Any change of the casting requiring a revised drawing ma

23、y require at the purchaser I s or manufacturers request : - manufacturing of new pre-production castings, or - modification of the manufacturing schedule and/or the inspecticn schedule. Copyright Association Europeene des Constructeurs de Materiel Aerospatial Provided by IHS under license with AECMA

24、Not for ResaleNo reproduction or networking permitted without license from IHS-,-,-AECMA PREN207b-03 87 M 1Ol123Ll 0007662 4 W prEN2076-3 Page 6 5.4 Manufacturing schedules and inspection schedules, which are modified during production shall be subjected to the same approval process as the .original

25、 documents. 5.5 Approved scrap may be added to the melt at the discretion of the manufacturer up to the maximum amount specified on the manufacturing schedule. 5.6 Correction of distortion shall be carried out only by agreement between the manufacturer and the purchaser. The manufacturer shall be re

26、sponsible for specifying the conditions under which such correction is to be carried out, subject to any provisions made by the purchaser. The method agreed shall be incorporated in the manufacturing schedule, After correction of distortion the castings shall be examined by penetrant flaw detection

27、as per clause 6 L .- i-. c .- 2 O u M M L! tj M U a W -a m W T- x w c + - E Copyright Association Europeene des Constructeurs de Materiel Aerospatial Provided by IHS under license with AECMANot for ResaleNo reproduction or networking permitted without license from IHS-,-,-AECMA PREN2076-03 7 LOL23LL

28、 0007670 3 prEN2076-3 Page 14 - e Table 2 - Radiographic acceptance standards for aluminium alloy castings up to a thickness of i 9 rnrn . Cracks, cold shuts or segregations are not acceptable Gas holes Shrinkage 1/4“ 1 2 4 (sponge) 3/4“ 1 2 3 1 /4“ -1 2 4 1 2 4 3/4“ Foreign material (less dense) Fo

29、reign materiai (more dense) 1 /4“ 1 2 4 1 1 3 3/4“ Any indication of the diffraction mottling phenomenom is acceptable provided it is confirmed to the satisfaction of the radiologist, either by additional radiographs at different angles, or by the cut-up of representative castings. Note : Acceptance

30、 standards for castings over 19 mm wall thickness shall be defined on the order, drawing or inspection schedule. Copyright Association Europeene des Constructeurs de Materiel Aerospatial Provided by IHS under license with AECMANot for ResaleNo reproduction or networking permitted without license fro

31、m IHS-,-,-1 /4“ 3/4“ 1 /4“ 3f 4“ 2 2 2 2 1 1 None 1 I AECMA PREN207b-03 87 3012333 0007673 5 m, _ prEN2076-3 Page 15 Table 3 - Radiographic acceptance standards for magnesium alloy . castings up to a thickness of G 19 mrn Cracks and cold shuts are not acceptable Acceptance standard reference plate n

32、umber Plate designation Defects GradeA 1 GradeB I GradeC 1 /4“ 3/4“ 1 1 3 3 5 4 Gas holes o Segregation Reacted sand inclusion Eutectic segregation Micro shrinkage type 1 /4“ 1 /4“ Gravity segregation 1 /4“ 2 Micro shrinkage (Feathery) 3 4 7 7 1 /4“ 3/4“ 1 /4“ 3/4“ 7 I 2 I 1 1 3 8 I I Foreign materi

33、al (less dense) 4 4 Foreign material (more dense) 2 2 lj Plate 1 for Mg-AI-Zn alloys not containing Zr. Any indication of the diffraction mottling phenornenom is acceptable provided it is confirmed to the satisfaction of the radiologist, either by additional radiographs at different angles, or by th

34、e cut-up of representative castings. Note : Acceptance standards for castings over 19 mm wall thickness shall be defined on the order, drawing or inspection schedule. d Copyright Association Europeene des Constructeurs de Materiel Aerospatial Provided by IHS under license with AECMANot for ResaleNo reproduction or networking permitted without license from IHS-,-,-