AECMA PREN 2369-1983 Wires Heat Resisting Alloys Diameter 0 2 mm Less Than or Equal to D Less Than or Equal to 8 mm Dimensions Aerospace Series Edition 1《航空航天系列抗热铝合金 10mm 小于或等于直径D小.pdf

1、- ! a u Approved by COMITE DE NORMALISATION of A .E C.M.A. 1982-07-26 AECflA PREN23b 83 1032341 0003019 3 m-d-z-Ls . i , - A.E.C.M.A. STANDARD pr EN2369 NORME A.E.C.M.A. Edition 1 A.E.C.M.A. NORM January 1983 The equivalent versions in French and German languages can be supplied by B.N.A.E., 8, rue

2、Moreau-Vauthier 92100 BOULOGNE-BILLANCOURT - FRANCE. I ENGLISH VERSION WIRES, HEAT RESISTING ALLOYS DIAMETER 0,2 mm D 8 mm DI MENSIONS AEROSPACE SERIES FILS EN ALLIAGES RESISTANT A CHAUD DIAMTRE 0,2 mm D 8 mm DIMENSIONS SERIE AEROSPATIALE LUFT- UND RAUMFAHRT DRHTE AUS HOCHWARMFESTEN LEGIERUNGEN DURC

3、HMESSER 0,2 mm D 8 mm MASZE 9 This industrial standard for the aerospace sector has been drawn up under the responsibility of AECMA (Association Europenne des Constructeurs de Matriel Arospatial). It is published on yellow paper in three equivalent versions (English, French, German). It will be subm

4、itted to CEN (European Committee for Standardization) as a draft European Standard. I- I II Copyright Association Europeene des Constructeurs de Materiel Aerospatial Provided by IHS under license with AECMANot for ResaleNo reproduction or networking permitted without license from IHS-,-,-_- AECMA PR

5、EN23b9 83 1012311 0003020 T CO NT E NTS 1 SCOPE AND FIELD OF APPLICATION 2 REFERENCES 3 MATERIALS 4 REQUIRED CHARACTERISTICS 5 DESIGNATION 6 TECHNICAL SPECIFICATION 7 I e e Copyright Association Europeene des Constructeurs de Materiel Aerospatial Provided by IHS under license with AECMANot for Resal

6、eNo reproduction or networking permitted without license from IHS-,-,-A.E.C.M.A. STANDARD prEN2369 WIRES, HEAT RESISTING ALLOYS DIAMETER 0,2 mm 4 D 4 8 mm DIMENSIONS SCOPE AND FIELD OF APPLICATION This standard specifies the dimensions and tolerances of heat resisting alloy wire used in aerospace co

7、nstruction. REFERENCES MATERIALS Inspection and testing requirements for titanium and heat resisting alloy wrought products - Part 1 : genral requirements Inspection and testing requirements for titanium and heat resisting alloy wrought products - Part 5 : inspection and t.esting requirements for wi

8、res. The materials are defined in the material standards. KEQUIRED CHARACTERISTICS 4.1 Preferred diameters See table 1. Copyright Association Europeene des Constructeurs de Materiel Aerospatial Provided by IHS under license with AECMANot for ResaleNo reproduction or networking permitted without lice

9、nse from IHS-,-,-;- A AECMA PREN2367 83 LOL23LL 0003022 3 -1: TABLE 1 Dimensions in millimetres Cross sectional Diameter area mm2 Mass * kglm Mass * kglm Cross sectional area mm2 Diameter 3,14 1 0,025 3,80 0,031 4/90 I O040 6/16 i-*O 7,OS-I 0,057 _ -I _ 0,4 I 0,126 i 0,0010 I 2.5 O .5 . 0,196 i 0,00

10、16 i 0,283 0,0024 9,62 1 0,078 12.57 I 0,102 - -_l_- 33 4,o e O 4,5 15.90 I 0,129 i 0,159 19,133 28,271 0,229 .I_ 6.3 31.17 1 0,252 38.48 ! 0,312 7 ,o 8,O . I 2,545 f 0,0206 I 50,27 I 0,407 * Calculated on the basis of an average density of 8,l g/cm3. 4.2 Tolerances on diameter See table 2. TABLE 2

11、Dimensions in millimetres . I l Diameter Tolerance I .I D04 2 0,006 i i_-. I_- -f- 0,013 0,3- .= D a 0,8 I 0,8 : D G 1,2 tr 0,020 1,2 *f D 2,O rt 0,030 I I_. 2,O D 3,O tr 0,040 i 3OD45 ._ ! t 0,045 ._ , . _ . -_I_ - _ ! 4,5 . D . 8,O i: 0,050 I Copyright Association Europeene des Constructeurs de Ma

12、teriel Aerospatial Provided by IHS under license with AECMANot for ResaleNo reproduction or networking permitted without license from IHS-,-,-e e a prEN2369 Page 5 5 DESIGNATION The designation of wire defined in this standard may include the following elements : name, number of material standard, d

13、imensions (diameter, length or mass), number of dimensional standard. 6 TECHNICAL SPECIFICATION The wire supplied to this standard shall conform with the requirements of EN2098-1 and EN2098-5. Copyright Association Europeene des Constructeurs de Materiel Aerospatial Provided by IHS under license with AECMANot for ResaleNo reproduction or networking permitted without license from IHS-,-,-