AECMA PREN 2912-1986 Aerospace Series Washers Flat Large Diameter Aluminium Alloy Issue P 1《航空航天系列大直径铝合金平垫圈 P 1》.pdf

1、ENGLISH VERSION Comments should be sent within six months after the date of publication decision Edition approved for publication Aerospace series Washers, flat, large diameter aluminium alloy C3 Chairman Srie arospatiale Rondelles plates larges, en alliage daluminium Luft- und Raumfahrt Scheiben, a

2、ngesenkt, groer Aupendurchmesser aus Aluminium This standard is initially published on green paper for the needs of AECMA-Members (Association Europenne des Constructeurs de Matriel Arospatial). It has been technically approved by the experts of the concerned AECMA Commission following comment by th

3、e manufacturers of the Member countries. After examination and signature of the AECMA Standard Checking Centre (NPS) and formal agreement of the Official Services of the Member countries it will be published in its final version on yellow paper as an AECMA Standard. Mr ARENA I A.E.C.M.A. 88, Bd. Mal

4、esherbes I 22 April 1986 I 75008 PARIS - FRANCE I Copyright Association Europeene des Constructeurs de Materiel Aerospatial Provided by IHS under license with AECMANot for ResaleNo reproduction or networking permitted without license from IHS-,-,-AECMA PREN2912 8b 1012311 0007050 b = Issue P 1 prEN2

5、912 Page 3 I Scope and field of application This standard specifies the characteristics of aluminium alloy flat washers with a large outside diameter (3 X inside diameter approx.) for use in aerospace.applications, at temperatures below 120 OC. They are intended for use with soft materiais to spread

6、 the bearing loads, and avoid surface damage. 2 References EN2090 EN2091 EN21 O1 EN23 1 9 EN2320 EN2424 , Aluminium alloy 2024-T3 P1 - Clad sheets and strips, 0,4 A 6 mm - Aerospace , Aluminium alloy 2024-T4 P1 - Clad sheets and strips, 0,4 A 6 mm - Aerospace , Aerospace series - Chromic acid anodic

7、ing of wrought aluminium alloys 1) , Aluminium alloy 2024-T351 O - Drawn bars A 75 mm - Aerospace series , Aluminium alloy 2024-T4 - Drawn bars A 75 mm - Aerospace series , Identification marking of standard fasteners - Aerospace series series series 3 Required characteristics 3.1 Configuration - Di

8、mensions - Tolerances Configuration shall correspond with the figure ; dimensions and tolerances shall correspond to figure and table after chromic anodising. 3.2 Surface roughness The values shown in the figure apply prior to chromic anodising. 3.3 Materials Aluminium alloy EN2090 or EN2091 or EN23

9、1 9 or EN2320. 3.4 Surface treatment Chromic acid anodising EN21 O1 with sealing. 1) In preparation. Copyright Association Europeene des Constructeurs de Materiel Aerospatial Provided by IHS under license with AECMANot for ResaleNo reproduction or networking permitted without license from IHS-,-,-AE

10、CMA PREN2912 Bb W 1012311 0007051 B W 0,6 I 06 issue P 1 prEN2912 Page 4 0,09 1 0,6 10 0,16 06 0,17 1 1 10 0,28 10 0,44 12 13 12 0,76 16 1 ,o1 12 1,6 12 1 ,o0 16 1,33 23 2 25 4,37 20 5,05 23 25 6,30 Break all corners 0.1 to 0.2 mm Figure - Configuration Table - Dimensions and tolerances Dimensions i

11、n millimetres Mass kg/l O00 pieces approx. 2) s 1) Thickness &IO% I code Diameter code dl HI3 d2 hl 4 d3 32 9 030 040 +o, 1 O 4,2 12 050 15 52 6 16 0,70 060 62 18 7,4 21 070 080 1 O0 120 +0,2 O -y+-+ 3,49 24 30 36 9,4 11,6 13,8 +0,3 O 1) Flatness variations are included in the thickness tolerance. 2

12、) Calculated on the basis of 2,85 kg/dms. Copyright Association Europeene des Constructeurs de Materiel Aerospatial Provided by IHS under license with AECMANot for ResaleNo reproduction or networking permitted without license from IHS-,-,-AECMA PREN2912 86 m 1012311 0007052 T - m _ - - / Issue P 1 ,

13、 prEN2912 Page 5 , 4 Desig-nation Each wwher shall only be designated as in the following example : / Description block WASHER Identity block EN291 2-08020 080 = diameter code (see table) Number of EN standard 20 = thickness code (see table) I Note : if necessary, the originator code S9005 may be in

14、troduced between the description block and the identity block. 5 Marking EN2424, style G. In addition to the quantity shall be stated (Mass or number). Copyright Association Europeene des Constructeurs de Materiel Aerospatial Provided by IHS under license with AECMANot for ResaleNo reproduction or networking permitted without license from IHS-,-,-