AECMA PREN 2962-1996 Aerospace Series Carbon Fibre Filament Yarn (Polyacrylonitrile Precursor) Technical Specification Edition P 1《航空航天系列碳丝纱线聚丙烯腈先驱技术规范.P1版》.pdf

1、 AECMA PRENx2962 96 1012311 DOL0422 418 Edition approved for publication 1996-05-31 AECMA STANDARD NORME AECMA AECMA NORM Comments should be sent within six months C7 Chairman after the date of publication to AECMA Guiledelle 94 Mr Wright B-1200 BRUXELLES 1 prEN 2962 Edition PI May 1996 PUBLISHED BY

2、 THE EUROPEAN ASSOCIATION OF AEROSPACE INDUSTRIES (AECMA) Gulledelle 94 - 8-1 200 BRUXELLES - Tel. (32) 2 775 81 10 - Fax. (32) 2 775 81 11 ICs : ENGLISH VERSION Aerospace series Carbon fibre filament yarn (Polyacrylonitrile precursor) Technical specification Srie arospatiale Fil de carbone (Prcurse

3、ur polyacrilonitrile) Spcification technique Luft- und Raumfahrt Kohlenstoffaser-Filarnentgarn (Ausgangsfaser Polyacrylnitril) Technische Lieferbedingungen This “Aerospace Series“ Prestandard has been drawn up under the responsibility of AECMA (The European Association of Aerospace Industries). It i

4、s published on green paper for the needs of AECMA-Members. It has been technically approved by the experts of the concerned Technical Committee following comment by the Member countries. Subsequent to the publication of this Prestandard, the technical content shall not be changed to an extent that i

5、nterchangeability is affected, physically or functionally, without re-identification of the standard. After examination and signature of the AECMA Standard Checking Centre (NPS) and formal agreement of the Official Services of the Member countries it will be submitted as a draft European Standard to

6、 CEN (European Committee for Standardization) for formal vote. COPYRIGHT Association Europeene Des Constructeurs de Materiel AerospaceLicensed by Information Handling Services- AECiIA PREN*2%62 %b 1012311 0010424 290 M Page 3 prEN 2962 : 1996 1 Scope This standard specifies the requirements for carb

7、on fibre filament yarn produced by the conversion of polyacrylonitrile precursor fibres. It is applicable whenever referenced on a material standard. 2 Normative references IS0 1890 IS0 2859-1 IS0 3951 IS0 10119 IS0 10120 IS0 10548 IS0 10618 IS0 11567 EN 2000 EN 2563 EN 3042 EN 4177-1 Textile glass

8、- Continuous filament yarns and staple fibre yarns - Determination of the twist Sampling procedures for inspection by attributes - Part 1 : Sampling plans indexed by acceptable quality level (AQL) for lot-by-lot inspection Sampling procedures and charts for inspection by variables for percent noncon

9、forming Carbon fibre - Determination of density Carbon fibre - Determination of linear density Carbon fibre - Determination of size content Carbon fibre - Determination of tensile properties by resin impregnated yarn specimens Carbon fibre - Determination of the diameter and cross sectional area of

10、carbon single filament Aerospace series - Quality assurance - EN aerospace products - Approval of the quality system of manufacturers Aerospace series - Carbon-thermosetting resin - Test method - Determination of apparent interlaminar shear strength 1) Aerospace series - Quality assurance - EN aeros

11、pace products - Qualification procedure Aerospace series - Fibre reinforced mouldings - Preparation of test panels of unidirectionally wound yarns and rovings 2) ASTM D 41 02-82 Standard Test Method for Thermal Oxidative Resistance of Carbon Fibers 3) 3 Definitions For the purposes of this standard,

12、 the following definitions apply : 3.1 Batch A production unit of material produced by the conversion of a number of precursor tows under controlled processing conditions in one continuous operation including any surface treatment and sizing of the fibre. 3.2 Elementary unit The smallest commerciall

13、y available entity of a given product (in the case of carbon filament yarn the elementary unit is a bobbin of given mass). 1 ) Published as AECMA Prestandard at the date of publication of this standard 2) In preparation at the date of publication of this standard 3) Published by : American Society f

14、or Testing and Materials (ASTM), 1916 Race Street, Philadelphia, PA 19103 COPYRIGHT Association Europeene Des Constructeurs de Materiel AerospaceLicensed by Information Handling Services AECMA PREN*2%62 b LOL2322 0030425 327 Page 4 prEN 2962 : 1996 3.3 Filament A continuous discrete fibre with a nom

15、inal diameter the cross section of which is not necessarily circular. 3.4 Size A substance added to the filament yarn to improve the handling characteristics and/or to promote the adhesion of a matrix material to the surface of the fibre. 3.5 Specimen A defined quantity of material on which measurem

16、ent is performed. 3.6 Surface treatment An electrochemical treatment to promote the adhesion of a polymer matrix to the surface of the fibre. 3.7 Linear density The mass per unit length of a yarn. 3.8 Density The mass per unit volume of a yarn. 4 Requirements 4.1 Composition The carbon fibre filamen

17、t yarn shall be made from a precursor fibre based on a polymer or copolymer of acrylonitrile. 4.2 Appearance The carbon fibre filament yarn shall be uniform in texture and shall be free from surface contaminants. The carbon fibre filament yarn shall not contain a level of physical defects which impa

18、irs its use. 4.3 Splices Each bobbin shall contain a continuous length of yarn with no splices. NOTE : If splices are unavoidable, the maximum number of splices per bobbin and the method of splicing shall be agreed between manufacturer and purchaser. Any splices shall be of sufficient strength for t

19、he requirement of the purchaser. 4.4 Surface treatment 4.4.1 When specified in the material standard the surface treatment shall be uniform from batch to batch. 4.4.2 The processing and control for the surface treatment shall be documented in the manufacturing schedule (see 5.3). 4.5 Finish 4.5.1 Th

20、e carbon fibre filament yarn may be supplied in one of the following conditions : a) unsized b) sized. or COPYRIGHT Association Europeene Des Constructeurs de Materiel AerospaceLicensed by Information Handling Services- AECMA PREM*2962 96 W 3032333 0030426 Ob3 m Page 5 prEN 2962 : 1996 4.5.2 the req

21、uirements specified in the material standard. The size content shall be determined in accordance with IS0 10548 and shall comply with 4.5.3 schedule (see 5.3). The type of size and the process for its application shall be documented in the manufacturing 4.5.4 The size shall conform to a reference in

22、fra-red spectrum established between the manufacturer and the mandated body at the time of qualification (5.2). 4.6 Oxidation resistance The resistance of the carbon fibre filament yarn to oxidation shall be determined in accordance with ASTM D 4102 and shall comply with the requirements of the mate

23、rial standard. 4.7 The linear density shall be determined in accordance with IS0 10120 and shall comply with the requirements of the material standard. Linear density (mass per unit length) 4.8 Density The density shall be determined in accordance with IS0 101 19 and shall comply with the requiremen

24、ts of the material standard. 4.9 Filament diameter and shape The diameter and shape of the cross section for the fibre yarn shall be determined in accordance with IS0 1 1567 and shall comply with the requirements of the material standard. 4.1 O Tensile properties The tensile strength, modulus and el

25、ongation of the fibre at break shall be determined in accordance with IS0 10618 and shall comply with the requirements of the material standard. 4.1 1 Twist 4.1 1 .I The yarn may be supplied with or without twist in accordance with the material standard. 4.11.2 When a definite level of twist is requ

26、ired the yarn shall be tested in accordance with IS0 1890 ; the sense of the twist and the nominal number of turns, per metre, shall comply with the requirements specified in the material standard. 4.12 Interlaminar shear strength The interlaminar shear strength shall be determined in accordance wit

27、h EN 2563 and shall comply with the requirements of the material standard. The test specimens shall be prepared in accordance with EN 2563 from a laminate manufactured in accordance with EN 41 77-1. 5 Quality assurance 5.1 Manufacturer approval Procedures for manufacturer approval shall be in accord

28、ance with EN 2000. COPYRIGHT Association Europeene Des Constructeurs de Materiel AerospaceLicensed by Information Handling ServicesPage 6 prEN 2962 : 1996 5.2 Product qualification Procedures for product qualification shall be in accordance with EN 3042. 5.3 Manufacturing schedule The manufacturer,

29、having regard for the provisions of EN 3042, shall document the processing conditions and control for the manufacture of the yarn. The manufacturing schedule shall be validated by the mandated body designated by AECMA-CERT. 5.4 Test requirements 5.4.1 The manufacturer having regard for the provision

30、s of EN 3042 shall implement a test programme, under the supervision of the mandated body designated by AECMA-CERT, on a minimum of three production batches of yarn. 5.4.2 The test programme shall include a statistical sampling plan (see 7) for each batch of yarn. 5.4.3 with the requirements given i

31、n table 1 - column 5. The elementary unit from each batch of yarn shall be inspected and tested in accordance 5.4.4 Each of the three production batches submitted for qualification shall comply with the property requirements and associated AQLs designated in the material standard. 6 Acceptance 6.1 M

32、anufacturing responsibility The manufacturer shall be responsible for the implementation of a statistical sampling plan and the relevant procedures for the inspection and test requirements as specified in 6.3 and 7 respectively. 6.2 Product acceptance 6.2.1 the associated AQLs designated in the mate

33、rial standard. Acceptability of a batch shall be determined in accordance with the sampling plan (see 7) and 6.2.2 specification and the material standard. Each batch of material released by the manufacturer shall be deemed to comply with this 6.3 Inspection and test requirements Each elementary uni

34、t shall be inspected and tested in accordance with the requirements of table 1 - column 6. 7 Sampling plan 7.1 the material standard. The elementary unit for inspection purposes shall be a bobbin of nominal mass as specified in 7.2 The sampling plan shall be in accordance with either a) IS0 2859-1 -

35、 Inspection level 2 b) IS0 3951 - (3 method or - Inspection level 2. COPYRIGHT Association Europeene Des Constructeurs de Materiel AerospaceLicensed by Information Handling ServicesAECMA PRENr2962 96 m 1012311 0010428 936 m Page 7 prEN 2962 : 1996 8 Packaging 8.1 fibre from moisture during delivery

36、and storage. Individual bobbins shall be packed in sealed polyethylene or equivalent bags to protect this 8.2 yarn in its proper condition. All bobbins shall be packed in suitable containers for shipping and delivery to maintain the 9 Marking NOTE : Attention is drawn to statutory regulations relati

37、ng to the marking of containers. 9.1 Each bobbin shall be clearly marked with a label on the inside of the core with the following : - product description ; - manufacturers name and product designation ; - batch and spool number ; - type of finish or treatment ; - net weight. 9.2 Each package shall

38、be permanently and legibly marked with the following - product description ; - manufacturers name product designation ; - manufacturers batch number. 1 O Certificate of conformity Each batch of material shall be accompanied by a certificate of conformity relative to the appropriate material standard

39、. COPYRIGHT Association Europeene Des Constructeurs de Materiel AerospaceLicensed by Information Handling ServicesAECMA PRENx29b2 9b m 1012311 0010429 872 m 2 3 Page 8 prEN 2962 : 1996 Mass per unit length I Fibre diameter and shape Table IS0 1890 IS0 10548 ASTM D 4102 I Il 1 3) 1 3) 1 1 5 2) 5 2) 2

40、 8 Tensile modulus 4 lo 516 - EN 2563 5 2) 5 2) Apparent interlaminar shear strength 3 Test condition Type of inspection or test II Number of specimens per elementary unit 1) Test method Qualification testing Acceptance testing 1 Testing of carbon fibre filament yarn in the delivery condition I 1 I

41、Density IS0 10119 IS0 10120 (23 f2) OC (50 f 51 % RH IS0 11567 1 4 I Twist z Size content I 6 I Oxidation resistance I Testing of tensile yarn specimens prepared in accordance with IS0 1061 8 5 l5 Tensile strength 171 (23 f 2) OC (50 k 5) % RH IS0 10618 5 5 I Testing of laminate specimens prepared i

42、n accordance with EN 4177-1 1) The number of elementary units is defined in the sampling plan (see 7.2). 2) Two elementary units are selected per batch of yarn for this test. 3) Minimum of 10 elementary units per batch. COPYRIGHT Association Europeene Des Constructeurs de Materiel AerospaceLicensed by Information Handling Services