AECMA PREN 3155-016-2005 Aerospace Series Electrical Contacts Used in Elements of Connection Part 016 Contacts Electrical Male Type A Crimp Class S Product Standard Edition P 2《航空航.pdf

1、AECMA STANDARD NORME AECMA AECMA NORM prEN 3155-016 Edition P 2 June 2005 PUBLISHED BY THE EUROPEAN ASSOCIATION OF AEROSPACE INDUSTRIES - STANDARDIZATION Gulledelle 94 - B-1200 Brussels - Tel. + 32 2 775 8110 - Fax. + 32 2 775 8111 - www.aecma-stan.orgICS: 49.060 Supersedes edition P 1 January 1999

2、Descriptors: ENGLISH VERSION Aerospace series Electrical contacts used in elements of connection Part 016: Contacts, electrical, male, type A, crimp, class S Product standard Srie arospatiale Contacts lectriques utiliss dans les organes de connexion Partie 016 : Contacts lectriques, mles, type A, se

3、rtir, classe S Norme de produit Luft- und Raumfahrt Elektrische Kontakte zur Verwendung in Verbindungselementen Teil 016: Elektrischer Buchsenkontakt, Typ A, crimpbar, Klasse S Produktnorm This “Aerospace Series“ Prestandard has been drawn up under the responsibility of AECMA-STAN (The European Asso

4、ciation of Aerospace Industries - Standardization). It is published for the needs of the European Aerospace Industry. It has been technically approved by the experts of the concerned Domain following member comments. Subsequent to the publication of this Prestandard, the technical content shall not

5、be changed to an extent that interchangeability is affected, physically or functionally, without re-identification of the standard. After examination and review by users and formal agreement of AECMA-STAN, it will be submitted as a draft European Standard (prEN) to CEN (European Committee for Standa

6、rdization) for formal vote and transformation to full European Standard (EN). The CEN national members have then to implement the EN at national level by giving the EN the status of a national standard and by withdrawing any national standards conflicting with the EN. Edition approved for publicatio

7、n 30 June 2005 Comments should be sent within six months after the date of publication to AECMA-STAN Electrical Domain Copyright 2005 by AECMA-STAN Copyright Association Europeene des Constructeurs de Materiel Aerospatial Provided by IHS under license with AECMANot for ResaleNo reproduction or netwo

8、rking permitted without license from IHS-,-,-prEN 3155-016:20052 Foreword This standard was reviewed by the Domain Technical Coordinator of AECMA-STANs Electrical Domain. After inquiries and votes carried out in accordance with the rules of AECMA-STAN defined in AECMA-STANs General Process Manual, t

9、his standard has received approval for Publication. Contents Page Introduction 3 1 Scope . 3 2 Normative references 3 3 Terms and definitions . 4 4 Required characteristics 4 4.1 Specific characteristics. 4 4.2 Dimensions, mass. 4 4.3 Marking 7 4.4 Material, surface treatment . 7 4.5 Permissible cab

10、les 7 4.6 Tooling 8 4.6.1 Crimping tools. 8 4.6.2 Insertion/Extraction tools . 9 4.7 Cable stripping 10 4.8 Tests 10 4.9 Gauges . 11 5 Designation. 12 6 Marking 12 7 Technical specification 12 Copyright Association Europeene des Constructeurs de Materiel Aerospatial Provided by IHS under license wit

11、h AECMANot for ResaleNo reproduction or networking permitted without license from IHS-,-,-prEN 3155-016:20053 Introduction The electrical contacts (except size 22) are derived from those of NAS 1749. 1 Scope This standard specifies the required characteristics, tests and tooling applicable to male e

12、lectrical contacts, type A, crimp, class S, used in elements of connection according to EN 3155-002. It shall be used together with EN 3155-001. The tests as applied in this standard do not permit the full qualification and shall be completed with associated components. 2 Normative references The fo

13、llowing referenced documents are indispensable for the application of this document. For dated references, only the edition cited applies. For undated references, the latest edition of the referenced document (including any amendments) applies. EN 2083, Aerospace series Copper or copper alloy conduc

14、tors for electrical cables Product standard. EN 2591*, Aerospace series Elements of electrical and optical connection Test methods. EN 3155-001, Aerospace series Electrical contacts used in elements of connection Part 001: Technical specification.1)EN 3155-002, Aerospace series Electrical contacts u

15、sed in elements of connection Part 002: List and utilization of contacts.1)EN 4008-007, Aerospace series Elements of electrical and optical connection Crimping tools and associated accessories Part 007: Positioner for crimping tool M22520/2-01 Product standard.1)EN 4008-008, Aerospace series Element

16、s of electrical and optical connection Crimping tools and associated accessories Part 008: Positioner for crimping tool M22520/7-01 Product standard.1)MIL-DTL-22520, Crimping tools, terminal, hand or power actuated, wire termination, and tool kits general specification for.2)MIL-C-22520/1, Crimping

17、tools, terminal, hand, wire termination for wire barrel sizes 12 through 20.2)MIL-C-22520/2, Crimping tools, terminal, hand, wire termination for wire barrel sizes 20 through 28.2)MIL-C-22520/7, Crimping tools, terminal, hand, wire termination for wire barrel sizes 16, 20 and 22.2) * All parts quote

18、d in this standard. 1) Published as AECMA Prestandard at the date of publication of this standard. 2) Published by: Department of Defense (DOD), The Pentagon, Washington D.C. 20301, USA. Copyright Association Europeene des Constructeurs de Materiel Aerospatial Provided by IHS under license with AECM

19、ANot for ResaleNo reproduction or networking permitted without license from IHS-,-,-prEN 3155-016:20054 MIL-I-81969, Installing and removal tools, connector electrical contact, general specification for.2)MIL-I-81969/14, Installing and removal Tools, Connector electrical Contact, Type III, Class 2,

20、Composition B.2) MIL-I-81969/30, Installing and removal tools, connector electrical contact, type II, class 2, composition C, for unwired contacts.2)NAS 1749, Contact, electrical, pin.3)3 Terms and definitions For the purposes of this document, the terms and definitions given in EN 3155-001 apply. 4

21、 Required characteristics 4.1 Specific characteristics Type A contacts are for general application and class S corresponds to an operating temperature range from 65 C to 200 C. 4.2 Dimensions, mass See Figure 1, Figure 2 and Table 1. Dimensions and tolerances are given in millimetres and apply after

22、 surface treatment. 3) Published by: National Standards Association, Inc., 1321, Fourteenth Street, N.W. Washington D.C. 20005, USA. Copyright Association Europeene des Constructeurs de Materiel Aerospatial Provided by IHS under license with AECMANot for ResaleNo reproduction or networking permitted

23、 without license from IHS-,-,-prEN 3155-016:20055 Key 1 A (Reference) 2 Diameter D (one side only) NOTE 1 for size 22, 0,08 E GNOTE 2 for all other sizes, 0,08 E M G M Figure 1 Male contact, size 22 X (2:1) Copyright Association Europeene des Constructeurs de Materiel Aerospatial Provided by IHS und

24、er license with AECMANot for ResaleNo reproduction or networking permitted without license from IHS-,-,-prEN 3155-016:20056 Key 1 A (Reference) 2 Dimple on for contact 20-20 3 Diameter D (one side only) 4 Blend radius 5 G (Reference) 6 R (Reference) aSize 12 crimp barrel Figure 2 Male contact, sizes

25、 20, 16 and 12 Y (10:1) aZ (2:1) Copyright Association Europeene des Constructeurs de Materiel Aerospatial Provided by IHS under license with AECMANot for ResaleNo reproduction or networking permitted without license from IHS-,-,-prEN 3155-016:20057 Table 1 Size A B C D E F G H J L M N P R Contact B

26、arrel (Ref.) Massg max. 22 22 8,33 1,70 1,65 0,83 0,73 0,630,370,940,851,501,451,221,143,813,711,171,123,032,790,45 0,35 5,30 5,18 0,07 20 20 7,37 0,88 0,64 0,83 0,73 0,820,661,271,222,622,541,981,934,704,001,981,933,032,790,45 0,35 1,67 1,57 4,34 4,06 1,801,700,16 20 18 7,37 0,88 0,64 0,83 0,73 0,8

27、20,661,351,302,622,541,981,934,704,001,981,933,032,790,45 0,35 1,67 1,57 4,34 4,06 1,801,700,16 16 16 9,95 0,88 0,64 1,22 1,12 1,070,911,731,683,383,302,622,577,206,402,622,573,423,180,45 0,35 2,06 1,88 6,53 6,25 2,342,180,34 12 12 10,820,88 0,64 1,22 1,12 1,070,912,592,494,834,753,843,767,206,403,8

28、43,764,394,150,56 0,46 3,10 3,00 6,53 6,25 3,453,310,80 4.3 Marking Dimple on front part of contact, see Figure 2. 4.4 Material, surface treatment Body material : copper alloy Surface treatment : gold on an appropriate undercoat, thickness of protection not specified 4.5 Permissible cables See Table

29、 2. Copyright Association Europeene des Constructeurs de Materiel Aerospatial Provided by IHS under license with AECMANot for ResaleNo reproduction or networking permitted without license from IHS-,-,-prEN 3155-016:20058 Table 2 Size Size of conductors Contact Barrel AECMA CodeSection AWG aRated tes

30、t current mm2A 22 22 004 002 001 0,40 0,25 0,15 22 24 26 5 3 2 20 20 006 004 002 0,60 0,40 0,25 20 22 24 7,5 5,0 3,0 20 18 010 006 004 002 1,00 0,60 0,40 0,25 18 20 22 24 7,5 7,5 5,0 3,0 16 16 012 010 006 1,20 1,00 0,60 16 18 20 13,0 10,0 7,5 12 12 030 020 3,00 2,00 12 14 23,0 17,0 aAWG = Nearest Am

31、erican Wire Gage. 4.6 Tooling 4.6.1 Crimping tools Conform to MIL-DTL-22520, see Table 4. The selector number used for crimping copper or copper alloy conductors in cables EN 2083 are indicated in Table 3. These selector numbers shall be used for qualification of the contacts and in service, unless

32、otherwise specified by the user. Copyright Association Europeene des Constructeurs de Materiel Aerospatial Provided by IHS under license with AECMANot for ResaleNo reproduction or networking permitted without license from IHS-,-,-prEN 3155-016:20059 Table 3 Size Cable size Tools M22520/1-01 Tools M2

33、2520/2-01 Tools M22520/7-01 Contact Barrel AECMA code AWG aPositioner SelectornumberPositioner Selector number Positioner Selectornumber001 26 2 2 002 24 2 3 004 22 3 4 22 22 Not applicable EN4008-007 EN4008-008 002 24 2 5 4 004 22 3 6 5 006 20 4 7 6 20 20 M22520/1-02Red M22520/2-02 M22520/7-02 002

34、24 2 5 4 004 22 3 6 5 006 20 4 7 6 20 18 010 18 M22520/1-02Red 5 M22520/2-02 8 M22520/7-02 7 006 20 4 5 010 18 5 6 012 16 6 7 16 16 M22520/1-02Blue Not applicable M22520/7-03 020 14 7 030 12 8 12 12 M22520/1-02Yellow Not applicable Not applicable aAWG: Nearest American Wire Gage. 4.6.2 Insertion/Ext

35、raction tools Conform to MIL-I-81969, see Table 4. Table 4 Size Extraction tools Contact Barrel Insertion tools Wired contact Unwired contact 22 22 M81969/14-01 M81969/14-01 M81969/30-08 20 20 M81969/14-11 M81969/14-11 M81969/30-05 20 18 M81969/14-11 M81969/14-11 M81969/30-05 16 16 M81969/14-03 M819

36、69/14-03 M81969/30-06 12 12 M81969/14-04 M81969/14-04 M81969/30-07 Copyright Association Europeene des Constructeurs de Materiel Aerospatial Provided by IHS under license with AECMANot for ResaleNo reproduction or networking permitted without license from IHS-,-,-prEN 3155-016:200510 4.7 Cable strip

37、ping See Table 5. Table 5 Size Contact Barrel Stripped length of cable mm 0,5 22 22 4 20 20 4,5 20 18 4,5 16 16 6,8 12 12 6,8 4.8 Tests See Table 6. Table 6 Applicable EN 2591- Test Not applicableAccording to EN 3155-001 Remarks 101 Visual examination X 102 Examination of dimensions and mass X 201 C

38、ontact resistance - low level X a 202 Contact resistance at rated current X a 204 Discontinuity of contacts in the microsecond range X a 206 Measurement of insulation resistance X 207 Voltage proof test X 210 Electrical overload X a 211 Capacitance X 212 Surface transfer impedance X 213 Shielding ef

39、fectiveness from 100 MHz to 1 GHz X 301 Endurance at temperature X T = (200 2) C Duration: 1 000 h 305 Rapid change of temperature X TA= (200 2) C TB= ( 65 2) C 306 Mould growth X 307 Salt mist X continued Copyright Association Europeene des Constructeurs de Materiel Aerospatial Provided by IHS unde

40、r license with AECMANot for ResaleNo reproduction or networking permitted without license from IHS-,-,-prEN 3155-016:200511 Table 6 (concluded) Applicable EN 2591- Test Not applicableAccording to EN 3155-001 Remarks 315 Fluid resistance X 319 Gastightness of solderless wrapped connections X 402 Shoc

41、k X a 403 Sinusoidal and random vibration X aAmbient temperature406 Mechanical endurance X a 415 Test probe damage (female contact) X 416 Contact bending strength X 417 Tensile strength (crimped connection) X 418 Gauge insertion/extraction forces (female contacts) X 424 Stripping force, solderless w

42、rapped connections X 425 Unwrapping capability, solderless wrapped connections X 501 Soft solderability X 502 Restricted entry X 503 Contact deformation after crimping X 507 Plating porosity X 508 Measurement of thickness of coating on contacts X The measured thickness shall be recorded509 Adhesion

43、of coating on contacts X 513 Magnetic permeability X 2 514 Solderability of contacts with self-contained solder and flux X aThis test shall be performed in conjunction with the mating components defined by EN 3155-002. 4.9 Gauges Not applicable Copyright Association Europeene des Constructeurs de Ma

44、teriel Aerospatial Provided by IHS under license with AECMANot for ResaleNo reproduction or networking permitted without license from IHS-,-,-prEN 3155-016:200512 5 Designation EXAMPLE Description block CONTACT, ELECTRICAL Identity block EN3155-016M2020 Number of this standard Type of contact M = ma

45、le Contact size code (see Table 1) Barrel size code (see Table 1) NOTE If necessary, the code I9005 shall be placed between the description block and the identity block. 6 Marking See EN 3155-001. 7 Technical specification See EN 3155-001. Copyright Association Europeene des Constructeurs de Materiel Aerospatial Provided by IHS under license with AECMANot for ResaleNo reproduction or networking permitted without license from IHS-,-,-