ImageVerifierCode 换一换
格式:PDF , 页数:7 ,大小:169.42KB ,
资源ID:420044      下载积分:5000 积分
快捷下载
登录下载
邮箱/手机:
温馨提示:
快捷下载时,用户名和密码都是您填写的邮箱或者手机号,方便查询和重复下载(系统自动生成)。 如填写123,账号就是123,密码也是123。
特别说明:
请自助下载,系统不会自动发送文件的哦; 如果您已付费,想二次下载,请登录后访问:我的下载记录
支付方式: 支付宝扫码支付 微信扫码支付   
验证码:   换一换

加入VIP,免费下载
 

温馨提示:由于个人手机设置不同,如果发现不能下载,请复制以下地址【http://www.mydoc123.com/d-420044.html】到电脑端继续下载(重复下载不扣费)。

已注册用户请登录:
账号:
密码:
验证码:   换一换
  忘记密码?
三方登录: 微信登录  

下载须知

1: 本站所有资源如无特殊说明,都需要本地电脑安装OFFICE2007和PDF阅读器。
2: 试题试卷类文档,如果标题没有明确说明有答案则都视为没有答案,请知晓。
3: 文件的所有权益归上传用户所有。
4. 未经权益所有人同意不得将文件中的内容挪作商业或盈利用途。
5. 本站仅提供交流平台,并不能对任何下载内容负责。
6. 下载文件中如有侵权或不适当内容,请与我们联系,我们立即纠正。
7. 本站不保证下载资源的准确性、安全性和完整性, 同时也不承担用户因使用这些下载资源对自己和他人造成任何形式的伤害或损失。

版权提示 | 免责声明

本文(AECMA PREN 3202-1989 Aerospace Series T-Head Bolt Traps Design Dimensions Issue P 1《航空航天系列.T头螺钉设计尺寸.P1版》.pdf)为本站会员(unhappyhay135)主动上传,麦多课文库仅提供信息存储空间,仅对用户上传内容的表现方式做保护处理,对上载内容本身不做任何修改或编辑。 若此文所含内容侵犯了您的版权或隐私,请立即通知麦多课文库(发送邮件至master@mydoc123.com或直接QQ联系客服),我们立即给予删除!

AECMA PREN 3202-1989 Aerospace Series T-Head Bolt Traps Design Dimensions Issue P 1《航空航天系列.T头螺钉设计尺寸.P1版》.pdf

1、AECMA PREN3202 89 B LOL2311 0004973 b A. E. C. M. A. STAN DARD NORM E A. E. C. M.A. A.E.C.M.A. NORM prEN 3202 Issue P 1 April 1989 _ _ DIT PAR LASSOCIATION EUROPENNE DES CONSTRUCTEURS DE MATRIEL AROSPATIAL 88. boulevard Malesherbes, 75008 PARIS - TL. 45-63-82-85 UDC ; Key words : ENGLISH VERSION Aer

2、ospace series T-head bolt traps Design dimensions Srie arospatiale Vis tte antirotation T Dimensions dinstallation Luft- und Raumfahrt T- Kopfschrau ben Einbaumape This .Aerospace Series pre-standard has been drawn up under the responsibility of AECMA (Association Europenne des Constructeurs de Matr

3、iel Arospatial). It is published on green paper for the needs of AECMA-Members. It has been technically approved b y the experts of the concerned AECMA Commission following comment by the Member countries. Subsequent to the publication of this pre-standard, the technical content shall not be changed

4、 to an extent that interchangeability is affected, physically or functionally, without re-identification of the standard. After examination and signature of the AECMA Standard Checking Centre (NPS) and formal agreement of the Official Services of the Member countries it will be submitted as a draft

5、European Standard to CEN (European Committee for Standardization) for final vote. Nota - Extra copies can be supplied by B.N.A.E. - 8, rue Moreau-Vauthier - 921 O0 BOULOGNE-BILLANCOURT Edition approved for publication Comments should be sent within six months C8 Chairman Mr WILLIAMS after the date o

6、f publication decision A.E.C.M.A. 88, Bd. Malesherbes 25th April 1989 75008 PARIS - FRANCE aecrna 1989 Copyright Association Europeene des Constructeurs de Materiel Aerospatial Provided by IHS under license with AECMANot for ResaleNo reproduction or networking permitted without license from IHS-,-,-

7、O * O O prEN 3202 Page 3 1 Scope and field of application This standard establishes a recommended practice for calculating the diameters of surfaces that interface with the head of tee head bolts. It prevents the bolt rotating during tightening and incorrect assembly, 2 General design information 2.

8、1 The minimum trap height should be the bolt head height. At places where the bolt head, during assembly, is inaccessible or not visible, the trap should be of such height that ensures head engagement before nut can be engaged on threads. Where this cannot be achieved a generous chamfer should be us

9、ed. This prevents a wrong assembly. See figure 1. Figure 1 - Minimum trap height 2.2 Selection of bolts The hole dimensions for bolts as per EN 2931, EN 2933 and EN 2935 are listed in table 1. The holes for bolts with f7-shank as per EN 3293, EN 3294 and EN 3301 are defined in table 2 and 3. 3 Insta

10、llation dimensions 3.1 Trap diameter The trap diameter definition is divided into two cases: - trap diameter smaller than pitch circle diameter, see 3.1.1 - trap diameter greater than pitch circle diameter, see 3.1.2. The diameter tolerance for the diameter F is t 0,l mm and the runout tolerance is

11、0,15 for cases with PD-shank bolts and 0,05 with f7-shank bolts. 7 .- I Previous page j is blank Copyright Association Europeene des Constructeurs de Materiel Aerospatial Provided by IHS under license with AECMANot for ResaleNo reproduction or networking permitted without license from IHS-,-,-prEN 3

12、202 Page 4 3.1.1 Trap diameter smaller than pitch circle diameter 1) Figure 2 The trap diameter is determined as follows: Formula 1: F = D - Smax - 0,6 3.1.2 Trap diameter greater than pitch circle diameter 1) 60 Figure 3 The trap diameter is determined as follows: Formula 2: F = J(D + Smax) + Emax2

13、- + 0,6 1) Figure 2 and 3 are only for illustration of formula 1 and 2. Copyright Association Europeene des Constructeurs de Materiel Aerospatial Provided by IHS under license with AECMANot for ResaleNo reproduction or networking permitted without license from IHS-,-,-31.2 Bolt hole +Op3 -0,l Thread

14、 Figure 4 D min s max 1) AECMA PREN3202 87 IOI23I1 OOOL1776 I m, MJ50,8 MJ6x1,O MJ7x1,O MJ8x1,O M JlOx1,25 prEN 3202 Page 5 098 70 894 098 70 995 0,8 80 10,5 098 90 11,5 0,8 90 13,3 3.2.1 PO-shank bolt Table 1 - Dimensions for PO-shank bolts 1) for recommendation only E max 11,6 12,5 13,9 14,5 17,O

15、all dimei H (H13) 5,5 +0,18 7,7 +0,22 6,6 +0,22 8,8 +0,22 10, +0,27 ;ions in mm C (HI41 6,4 +0,36 7,9 +0,36 9,O +0,36 10,l +0,43 12,2 +0,43 The positional tolerance for H is 0,25 diameter at maximum material condition. Copyright Association Europeene des Constructeurs de Materiel Aerospatial Provide

16、d by IHS under license with AECMANot for ResaleNo reproduction or networking permitted without license from IHS-,-,-AECMA PKEN3202 49 lIOL231L OOOLI977 3 i prEN 3202 Page 6 Pitch circle diameter over to O 75 75 250 250 750 7 50 1600 1600 - 3.2.2 f7-shank bolts in rotating parts Positional tolerance

17、at max. material condition 8 044 8 05 8 0,08 OJO 0,12 Table 2 - Hole dimensions all dimensions in mm Thread MJ5098 M J6x1,O MJlx1,O MJ8x1,O M JlOx1,25 +0,028 5,0 +0,01 +0,028 +0,01 +0,035 7,0 +0,013 +0,035 890 +0,013 +0,035 +0,013 The above-mentioned hole dimensions ensure that the bolts are more ac

18、curately located during engine build and re-build, so lessening out of balance possibilities. Table 3 - Positional tolerances all dimensions in mm Copyright Association Europeene des Constructeurs de Materiel Aerospatial Provided by IHS under license with AECMANot for ResaleNo reproduction or networ

19、king permitted without license from IHS-,-,-AECMA PREN3202 89 W LOL23Ll 0004978 5 W prEN 3202 Page 7 . 3.2.3 f7-shank bolts as positioning bolts Table 4 - Hole dimensions all dimensions in mm 1 Thread MJ5x0,8 MJ6x1,O MJ8x1,O MJ10x1,25 MJ7xljO H (H7) 5,O +0,012 6,O +0,012 7,O +0,015 8,O +0,015 10,O +

20、0,015 I Dimensions R, D, S, E, C see table 1. I The positional tolerance for #I H is 0,Ol diameter at max,num materiai condition. 3.3 Trap height 3.3.1 The preferred height at visible places A2 min is equal to the bolt head height. Table 5 - Trap height all dimensions in mm I Thread I A2 min I MJ5x0

21、,8 M J6x1,O MJ7x1,O MJ8x1,O M JlOx1,25 Figure 5 - Height A2 min Copyright Association Europeene des Constructeurs de Materiel Aerospatial Provided by IHS under license with AECMANot for ResaleNo reproduction or networking permitted without license from IHS-,-,-AECMA PREN3202 89 IB 1012311 0004379 7

22、prEN 3202 Page 8 3.3.2 Height at not visible or inaccessible places A1 min = N - (6 + C) Figure 6 - Height A1 min 4 Drawing callout Figure 7 shows a typical drawing callout for a hole for PD-shank bolts as per paragraph 3.2.1. Figure 7 -hl - Drawing callout a Copyright Association Europeene des Constructeurs de Materiel Aerospatial Provided by IHS under license with AECMANot for ResaleNo reproduction or networking permitted without license from IHS-,-,-

copyright@ 2008-2019 麦多课文库(www.mydoc123.com)网站版权所有
备案/许可证编号:苏ICP备17064731号-1