AECMA PREN 3240-1992 Aerospace Series Nuts Self-Locking Clip in Heat Resisting Steel FE-PA92HT (A286) Uncoated Classification 1 100 MPa (at Ambient Temperature) 425 Degrees Celsiu.pdf

1、-.-_-_I_-_ CEN PRE“*324B 92 W 3404589 0029273 302 A. E .C. M .A. STAN DARD NORME A.E.C.M.A. A.E.C.M.A. NORM prEN 3240 Issue P 2 July 1992 EDIT PAR LASSOCIATION EUROPENNE DES CONSTRUCTEURS DE MATERIEL AROSPATIAL Technopolis - 175, rue Jean-Jacques Rousseau - F-92138 Issy-les-Moulineaux Cdex -Tl. (1)

2、47.36.98.76 Supersedes issue PI April 1989 UDC : Key words : ENGLISH VERSION Aerospace series Nuts, seif-locking, clip, in heat resisting steel FE-PA92HT (A286), uncoated Classification : I 100 MPa (at ambient temperature) / 425 OC Srie arospatiale Luft- und Raumfahrt crous pincer, freinage interne,

3、 en acier rsistant chaud FE-PA92HT (A286), Classification : 1 I O0 MPa ( temprature ambiante) / 425 OC Klemmuttern, selbstsichernd, aus hochwarmfestem Stahl FE-PA92HT (A286), Klasse : 1 100 MPa (bei Raumtemperatur) / 425 OC non revtus blank This Aerospace Series. pre-standard has been drawn up under

4、 the responsibility of AECMA (Association Europenne des Constructeurs de Matriel Arospatial). It is published on green paper for the needs of AECMA-Members. It has been technically approved by the experts of the concerned Commission following comment by the Member countries. Subsequent to the public

5、ation of this pre-standard, the technical content shall not be changed to an extent that interchangeability is affected, physically or functionally, without re-identification of the standard. After examination and signature of the AECMA Standard Checking Centre (NPS) and formal agreement of the Offi

6、cial Services of the Member countries it will be submitted as a draft European Standard to CEN (European Committee for Standardization) for final vote. Nota - Extra copies can be supplied by B.N.A.E. - Technopolis 54. 199. rue Jean-Jacques Rousseau - 92138 ISSY-LES-MOULINEAUX CEDEX Edition approved

7、for publication 1992-07-06 Comments should be sent within six months after the date of publication decision A.E.C.M.A. Technopolis - 175, rue Jean-Jacques Rousseau 921 38 Issy-les-Moulineaux Cdex - FRANCE C8 Chairman Mr. WILLIAMS aecma 1992 Copyright Association Europeene des Constructeurs de Materi

8、el Aerospatial Provided by IHS under license with AECMANot for ResaleNo reproduction or networking permitted without license from IHS-,-,-prEN 3240 Page 3 1 Scope This standard specifies the characteristics of self-locking clip nuts in FE-PA92HT for aerospace applications. . Classification : 1100 MP

9、a )/425 OC 2, 2 References IS0 5855-1, Aerospace - MJ threads - Part 1 : General requirements IS0 5855-2, Aerospace - MJ threads - Part 2 : Limit dimensions for bolts and nuts EN 2424, Aerospace series - Identification marking of standard fasteners 3, EN 3152, Aerospace series - Propulsion standard

10、parts - Nuts, self-locking, in heat resisting steel FE-PA92HT (A286) - Classification : 1100 MPA/425 OC - Technical specification 4) EN 3638, Aerospace series - Heat resisting alloy FE-PA92HT - Solution treated - Sheet and strip a s 3 mm 5, EN 3639, Aerospace series - Heat resisting alloy FE-PA92HT

11、- Rm 2 900 MPa - Cold worked and softened - Bar and wire for continuous cold forging or extrusion of fasteners - 3sD30mm5) EN 3741, Aerospace series - Clip nuts, metric - Installation holes and assembly 5, 3 Required characteristics 3.1 Configuration - Dimensions - Tolerances - Masses The configurat

12、ion of the clip nut in this standard is given as an example only. Forms not stated are at the manufacturers option. Only the maximum overall dimensions given in the table 1 and the interchangeability requirements are imposed. The minimum dimensions are limited by the requirements of the technical sp

13、ecification. Dimensions and tolerances are in millimeters. 3.2 Material Nut element : EN 3638 or EN 3639 Clip : EN 3638 1) The strength class of the bolt concerned which can withstand the load at ambient temperature when tested at 100% load without cracking or breaking the nut. 2) Maximum test tempe

14、rature of the part 3) Published as AECMA standard at the date of publication of the present standard 4) Published as AECMA pre-standard at the date ot publication of the present standard 5) In preparation at the date of publication of the present standard Previous page is blank Copyright Association

15、 Europeene des Constructeurs de Materiel Aerospatial Provided by IHS under license with AECMANot for ResaleNo reproduction or networking permitted without license from IHS-,-,- -_ _. CEN PRENx3240 92 E 3404589 0029273 T85 E prEN 3240 Page 4 6.3 Thread surfaces will be as achieved by normal method of

16、 manufacture J View B-B View A-A Deformation in this area to achieve self locking requirement Tooling marks acceptable Identity Markings t Remove sharp edges 0,l to 0,4 All forms are acceptable within limit dimensions. Figure 1 Table 1 - Dimensions and Masses Thread 8.05 K 10 6.6 f 0,05 max. min. kg

17、11000 Thickness Range 2.6 0.9-2 Copyright Association Europeene des Constructeurs de Materiel Aerospatial Provided by IHS under license with AECMANot for ResaleNo reproduction or networking permitted without license from IHS-,-,- - CEN PREN*3240 92 = 3404589 0029274 911 ! 4 Designation Example : Des

18、cription block Identity block prEN 3240 Page 5 NUT EN3240-0t I I- Number of this standard ( Diameter code (see table 1) 3 - Note : If necessary, the design code 19005 shall be placed between the description block and the identity block. 5 Marking EN 2424, style F, at the location shown in the figure 1 6 Technical specification EN 3152 Copyright Association Europeene des Constructeurs de Materiel Aerospatial Provided by IHS under license with AECMANot for ResaleNo reproduction or networking permitted without license from IHS-,-,-