AECMA PREN 3372-011-2005 Aerospace series Connectors electrical circular medium and high contact density scoop-proof with bayonet coupling operating temperatures - 65 degrees C to 1.pdf

1、AECMA STANDARD NORME AECMA AECMA NORM prEN 3372-011 Edition P 1 June 2005 PUBLISHED BY THE EUROPEAN ASSOCIATION OF AEROSPACE INDUSTRIES - STANDARDIZATION Gulledelle 94 - B-1200 Brussels - Tel. + 32 2 775 8110 - Fax. + 32 2 775 8111 - www.aecma-stan.orgICS: 49.060 Descriptors: ENGLISH VERSION Aerospa

2、ce series Connectors, electrical, circular, medium and high contact density, scoop-proof with bayonet coupling, operating temperatures 65 C to 175 C or 200 C continuous Part 011: Dummy receptacle Product standard Srie arospatiale Connecteurs lectriques circulaires scoop-proof accouplement par baonne

3、ttes temprature dutilisation 65 C 175 C ou 200 C continu Partie 011: Embase de repos Norme de produit Luft- und Raumfahrt Elektrische Rundsteckverbinder, kontaktgeschtzt, Bajonettkupplung, Betriebstemperatur 65 C bis 175 C oder 200 C konstant Teil 011: Blinddose Produktnorm This “Aerospace Series“ P

4、restandard has been drawn up under the responsibility of AECMA-STAN (The European Association of Aerospace Industries - Standardization). It is published for the needs of the European Aerospace Industry. It has been technically approved by the experts of the concerned Domain following member comment

5、s. Subsequent to the publication of this Prestandard, the technical content shall not be changed to an extent that interchangeability is affected, physically or functionally, without re-identification of the standard. After examination and review by users and formal agreement of AECMA-STAN, it will

6、be submitted as a draft European Standard (prEN) to CEN (European Committee for Standardization) for formal vote and transformation to full European Standard (EN). The CEN national members have then to implement the EN at national level by giving the EN the status of a national standard and by withd

7、rawing any national standards conflicting with the EN. Edition approved for publication 30 June 2005 Comments should be sent within six months after the date of publication to AECMA-STAN Electrical Domain Copyright 2005 by AECMA-STAN Copyright Association Europeene des Constructeurs de Materiel Aero

8、spatial Provided by IHS under license with AECMANot for ResaleNo reproduction or networking permitted without license from IHS-,-,-prEN 3372-011:20052 Foreword This standard was reviewed by the Domain Technical Coordinator of AECMA-STANs Non-metallic Material Domain. After inquiries and votes carrie

9、d out in accordance with the rules of AECMA-STAN defined in AECMA-STANs General Process Manual, this standard has received approval for Publication. Contents Page 1 Scope 3 2 Normative references 3 3 Terms and definitions .3 4 Required characteristics.4 5 Designation 6 6 Marking .6 7 Technical speci

10、fication .6 Copyright Association Europeene des Constructeurs de Materiel Aerospatial Provided by IHS under license with AECMANot for ResaleNo reproduction or networking permitted without license from IHS-,-,-prEN 3372-011:20053 1 Scope This standard specifies the characteristics of dummy receptacle

11、s in the family of circular electrical connectors coupled by bayonet ring. It applies to class defined in Table 3. For plugs, see EN 3372-008. 2 Normative references The following referenced documents are indispensable for the application of this document. For dated refer-ences, only the edition cit

12、ed applies. For undated references, the latest edition of the referenced document (including any amendments) applies. EN 3372-001, Aerospace series Connectors, electrical, circular, medium and high contact density, scoop-proof with bayonet coupling, operating temperatures 65 C to 175 C or 200 C cont

13、inuous Part 001: Technical specification1)EN 3372-002, Aerospace series Connectors, electrical, circular, medium and high contact density, scoop-proof with bayonet coupling, operating temperatures 65 C to 175 C or 200 C continuous Part 002: Specification of performance and contact arrangements1)EN 3

14、372-008, Aerospace series Connectors, electrical, circular, medium and high contact density, scoop-proof with bayonet coupling, operating temperatures 65 C to 175 C or 200 C continuous Part 009: Free plug with grounding ring Product standard1)3 Terms and definitions According to EN 3372-001. 1) Publ

15、ished as AECMA Prestandard at the date of publication of this standard Copyright Association Europeene des Constructeurs de Materiel Aerospatial Provided by IHS under license with AECMANot for ResaleNo reproduction or networking permitted without license from IHS-,-,-prEN 3372-011:20054 Required cha

16、racteristics 4.1 Dimensions, mass See Figure 1 and Table 1. For position of the interfacial seal refer to EN 3372-001, Figure 1. Dimensions and tolerances in millimetres; they apply after surface treatment Figure 1 Dummy receptacle Table 1 Dimensions and mass b1d1d5e l20X P Panel Thickness Mass g mm

17、 mm mm mm mm Degree mm Housing size 0,4 0,13 max. 0,1 00,13+ 2 max. max. 08 20,6 27,2 15,1 18 4,0 10 23,8 32,0 18,3 28 5,0 12 26,2 35,2 20,6 32 7,0 14 28,6 38,4 23,0 34 9,0 16 31,0 41,5 24,6 10,0 18 33,3 44,7 27,0 16,05 12,0 20 36,5 47,9 29,4 30 13,0 22 39,7 3,05 51,1 31,8 3,0 15,0 24 42,9 3,73 55,8

18、 34,9 15,29 26 2,26 16,0 4 Copyright Association Europeene des Constructeurs de Materiel Aerospatial Provided by IHS under license with AECMANot for ResaleNo reproduction or networking permitted without license from IHS-,-,-prEN 3372-011:20054.2 Panel cut-out and mounting of connectors See Figure 2

19、and Table 2 for panel cut-out and mounting of connectors. Dimensions and tolerances in millimetres aBack panel mounting bFront panel mounting D min. value is calculated as follows: D connector one + D connector two (see Table 2 for value D). Figure 2 Panel cut-out and mounting Table 2 Panel cut-out,

20、 dimensions Dimensions in mm A A1R L D Housing size 0,1 0,1 0,2 0,2 min. 08 14,0 12,7 15,1 28,0 10 17,0 16,0 18,3 31,0 12 22,0 19,0 20,6 36,0 14 25,0 22,2 23,0 41,0 16 28,0 25,5 24,6 43,0 18 31,0 28,5 27,0 46,0 20 34,5 31,7 29,4 53,0 22 37,5 35,0 31,8 3,5 58,0 24 41,0 38,0 34,9 4,0 61,0 5 Copyright

21、Association Europeene des Constructeurs de Materiel Aerospatial Provided by IHS under license with AECMANot for ResaleNo reproduction or networking permitted without license from IHS-,-,-prEN 3372-011:20054.3 Material, surface treatment See Table 3. 4.4 Main general characteristics According to EN 3

22、372-002. 4.5 Possible combinations of plugs and receptacles According to EN 3372-002. 5 Designation EXAMPLE Description block Identity block ELECTRICAL CONNECTOR, RECEPTACLE EN3372 W 5 18 6 Number of basic standard Class (see Table 3) Dummy receptacle (see EN 3372-002) Housing size and contact arran

23、gement (see EN 3372-002) NOTE If necessary, the code I9005 shall be placed between the description block and the identity block. Table 3 Connector class Class Description W Cadmium-plated aluminium alloy, olive drab 500 h salt mist Maximum operating temperature 175 C continuous F Nickel-plated alumi

24、nium alloy 48 h salt mist Maximum operating temperature 200 C continuous 6 Marking Unless there are other specific contractual requirements, the marking shall include: the identity block as defined in Clause 5. the date of manufacture (year, week); the manufacturers name or trade mark. 7 Technical specification According to EN 3372-001. Copyright Association Europeene des Constructeurs de Materiel Aerospatial Provided by IHS under license with AECMANot for ResaleNo reproduction or networking permitted without license from IHS-,-,-