AECMA PREN 3545-003-2004 Aerospace series Connectors electrical rectangular with sealed and non-sealed rear plastic housing locking device operating temperatures - 55 Degrees C to .pdf

1、AECMA STANDARD NORME AECMA AECMA NORM Edition approved for publication 30 September 2004 prEN 3545-003 Edition P 3 September 2004 Comments should be sent within six months after the date of publication to Electrical Domain AECMA-STAN ICs: 49.060 Descriptors: Supersedes edition P 2 October 2002 ENGLI

2、SH VERSION Aerospace series Connectors, electrical, rectangular, with sealed and non-sealed rear, plastic housing, locking device, operating temperatures - 55 OC to 175 OC Part 003: Connectors with female contacts - Product standard Srie arospatiale Luft- und Raumfahrt Connecteurs lectriques, rectan

3、gulaires, Elektrische Rechtecksteckverbinder tanches et non tanches larrire, botier en plastique, verrouillage, tempratures dutilisation - 55 OC 175 OC Partie 003 : Connecteurs contacts femelles - mit und ohne hintere Abdichtung, Plastikgehuse, Verriegelungssystem, Betriebstemperaturen von - 55 OC b

4、is 175 OC Teil 003: Steckverbinder mit Buchsenkontakten - Norme de produit Produktnorm This “Aerospace Series“ frestandard has been drawn up under the responsibility of AECMA-STAN (The European Association of Aerospace Industries - Standardization). It is published for the needs of the European Aero

5、space Industry. It has been technically approved by the experts of the concerned Domain following member comments. Subsequent to the publication of this frestandard, the technical content shall not be changed to an extent that interchangeabilify is affected, physically or functionally, without re-id

6、entification of the standard. After examination and review by users and formal agreement of AECMA-STAN, it will be submitted as a draft European Standard (prEN) to CEN (European Committee for Standardization) for formal vote and transformation to full European Standard (EN). The CEN national members

7、 have then to implement the EN at national level by giving the EN the status of a national standard and by withdrawing any national standards conflicting with the EN. I I Copytight 2004 O by AECMA-STA1 Copyright Association Europeene des Constructeurs de Materiel Aerospatial Provided by IHS under li

8、cense with AECMANot for ResaleNo reproduction or networking permitted without license from IHS-,-,-Page 2 prEN 3545-003:2004 Foreword This standard was reviewed by the Domain Technical Coordinator of AECMA-STANS Electrical Domain. After inquiries and votes carried out in accordance with the rules of

9、 AECMA-STAN defined in AECMA- STANS General Process Manual, this standard has received approval for Publication. Contents Page 1 Scope 2 Normative references 3 4 Required characteristics 5 Designation 6 Delivery conditions 7 Marking 8 Technical specification Def i n it i on s Copyright Association E

10、uropeene des Constructeurs de Materiel Aerospatial Provided by IHS under license with AECMANot for ResaleNo reproduction or networking permitted without license from IHS-,-,-Page 3 prEN 3545-003:2004 1 Scope This standard specifies connectors with female contacts in the family of rectangular electri

11、cal connectors with sealed and non-sealed rear, plastic housing, locking device, for operating temperatures from - 55 “C to 175 “C. These connectors may be used as receptacles (fixed housings) or plugs (free housings) in conjunction with the following coding and attachment system: - male coding and

12、attachment system for mounting on a fixed housing; - female coding and attachment system for mounting on a free housing. 2 Normative references This European Standard incorporates by dated or undated reference, provisions from other publications. These normative references are cited at the appropria

13、te places in the text and the publications are listed hereafter. For dated references, subsequent amendments to or revisions of any of these publications apply to this European Standard only when incorporated in it by amendment or revision. For undated references the latest edition of the publicatio

14、n referred to applies (including amendments). EN 31 55-002, EN 3545-001 , Aerospace series - Electrical contacts used in elements of connection - Part 002: List and utilization of contacts 1) Aerospace series - Connectors, electrical, rectangular, with sealed and non-sealed rear, plastic housing, lo

15、cking device, operating temperatures - 55 “C to 175 “C - Part 001: Technical specification 1) Aerospace series - Connectors, electrical, rectangular, with sealed and non-sealed rear, plastic housing, locking device, operating temperatures - 55 “C to 175 “C - Part 002: Specification of performance an

16、d contact arrangements 1) EN 3545-002, 3 Def i n i ti ons See EN 3545-001. 4 Required characteristics 4.1 Dimensions, mass See Figure 1, Figure 2 and Table 1. Dimensions and tolerances are in millimetres. Mass (without accessory and without contact) - non-sealed housing: 19 g max.; - sealed housing:

17、 21 g Max. 1) Published as AECMA Prestandard at the date of publication of this standard Copyright Association Europeene des Constructeurs de Materiel Aerospatial Provided by IHS under license with AECMANot for ResaleNo reproduction or networking permitted without license from IHS-,-,-Page 4 prEN 35

18、45-003:2004 Key 1 Grommet for rear sealing 4 23 max. for contact arrangement 07 and 08 2 Female contact 35 max. for contact arrangement 16 3 20 max. for other contact arrangements 14,lO max. for contact arrangement 07 and 08 26,l max. for contact arrangement 16 15 max. for other contact arrangements

19、 a Applicable dimensions for contact arrangement 07 and 08 Figure 1 Copyright Association Europeene des Constructeurs de Materiel Aerospatial Provided by IHS under license with AECMANot for ResaleNo reproduction or networking permitted without license from IHS-,-,-Page 5 prEN 3545-003:2004 Key 1 Rea

20、r grommet 2 Female contact 3 4 a Electrical point of female contact, see EN 3545-001. (46,5 f 2)“ for contact size 8 (45 f 2)“ for other contacts Not applicable for arrangement code 07 and 08 Figure 2 Copyright Association Europeene des Constructeurs de Materiel Aerospatial Provided by IHS under lic

21、ense with AECMANot for ResaleNo reproduction or networking permitted without license from IHS-,-,-Page 6 prEN 3545-003:2004 Table 1 Cavity contact for lDIEl F 3,66 I I 429 l2 I 3,56 4,22 4.2 Recommended panel cut-out for connectors fitted with male coding and attachment system See Figure 3. Maximum

22、thickness of panel: 1,6 Minimum pitch between connectors: 14,2 Figure 3 4.3 Main general characteristics See EN 3545-002. Copyright Association Europeene des Constructeurs de Materiel Aerospatial Provided by IHS under license with AECMANot for ResaleNo reproduction or networking permitted without li

23、cense from IHS-,-,-Page 7 prEN 3545-003:2004 5 Designation EXAMPLE L c, O o a C C O o a C O EJ a 5 L E c, O z Description block I Identity block CONNECTOR, ELECTRICAL I EN35451 T Number of the basic standard I Type of housing: D: non-sealed E: sealed O1 FXB: _ Contact arrangement (see EN 3545-002) T

24、ype of contact: F: female contact (male housing) Contact connection: X: crimping Type of coding and attachment system: I - female for mounting on free housing (plug): A - male for mounting on fixed housing (receptacle): B - coding and attachment system not delivered: without code Coding 2) (see EN 3

25、545-002): - Ist digit: position of index 1 to 6 for cavity A - 2nd digit: position of index 1 to 6 for cavity B - 00: code not defined - without code, coding and attachment system not delivered Delivery conditions 3) - connector without contacts, with coding and attachment system: A - connector with

26、 contacts (version 1, see Table 2) and coding and attachment system: B - connector with contacts (version 2, see Table 2) and with coding and attachment system: D - connector without contact and without coding and attachment system: without code NOTE If necessary, the code 19005 shall be placed betw

27、een the description block and the identity block. 6 Delivery conditions The delivered contacts according to the contact arrangements are given in Table 2. The contacts size 8 are always delivered separately. 2) The coding is given as information for users. 3) Where a connector is ordered with its fi

28、ttings, these may be delivered not fitted Copyright Association Europeene des Constructeurs de Materiel Aerospatial Provided by IHS under license with AECMANot for ResaleNo reproduction or networking permitted without license from IHS-,-,-Page 8 prEN 3545-003:2004 Table 2 Version 1 I Delivery condit

29、ions code B D I Version 2 a See EN 3155-002. Only applicable to contact arrangements codes 01, 03 and 04 Delivered with female contacts a EN 31 55-003F2222 EN 3155-015F2018 EN 3155-003F1614 EN 3155-003F1212 EN 3155-003F1010 EN 31 55-01 5F2020 EN 31 55-003F1616 7 Marking Unless there are other specif

30、ic contracted requirements, the marking shall include: - the part of identity block as defined in 5; - the date of manufacture (yeadweek); - the manufacturers name or trademark. 8 Technical specification See EN 3545-001. Copyright Association Europeene des Constructeurs de Materiel Aerospatial Provided by IHS under license with AECMANot for ResaleNo reproduction or networking permitted without license from IHS-,-,-