AECMA PREN 3545-007-2004 Aerospace Series Connectors Electrical Rectangular with Sealed and Non-Sealed Rear Plastic Housing Locking Device Operating Temperatures - 55 Degrees C to .pdf

1、AECMA STANDARD NORME AECMA AECMA NORM Edition approved for publication 31 August 2004 prEN 3545-007 Edition P 3 August 2004 Comments should be sent within six months after the date of publication to Electrical Domain AECMA-STAN ICs: 49.060 Descriptors: Superseding edition P 2 October 2002 ENGLISH VE

2、RSION Aerospace series Connectors, electrical, rectangular, with sealed and non-sealed rear, plastic housing, locking device, operating temperatures - 55 OC to 175 OC Part 007: Cable clamp Product standard Srie arospatiale Luft- und Raumfahrt Connecteurs lectriques, rectangulaires, Elektrische Recht

3、ecksteckverbinder tanches et non tanches larrire, mit und ohne hintere Abdichtung, botier en plastique, verrouillage, Plastikgehse, Verriegelunssystem, tempratures dutilisation - 55 OC 175 OC Betriebstemperaturen von - 55 OC bis 175 OC Partie 007 : Serre-cble Teil 007: Zugentlastungsklemme Norme de

4、produit Produktnorm This “Aerospace Series“ frestandard has been drawn up under the responsibility of AECMA-STAN (The European Association of Aerospace Industries - Standardization). It is published for the needs of the European Aerospace Industry. It has been technically approved by the experts of

5、the concerned Domain following member comments. Subsequent to the publication of this frestandard, the technical content shall not be changed to an extent that interchangeabilify is affected, physically or functionally, without re-identification of the standard. After examination and review by users

6、 and formal agreement of AECMA-STAN, it will be submitted as a draft European Standard (prEN) to CEN (European Committee for Standardization) for formal vote and transformation to full European Standard (EN). The CEN national members have then to implement the EN at national level by giving the EN t

7、he status of a national standard and by withdrawing any national standards conflicting with the EN. I I Copytight 2004 O by AECMA-STA1 Copyright Association Europeene des Constructeurs de Materiel Aerospatial Provided by IHS under license with AECMANot for ResaleNo reproduction or networking permitt

8、ed without license from IHS-,-,-Page 2 prEN 3545-007:2004 Foreword This standard was reviewed by the Domain Technical Coordinator of AECMA-STANS Electrical Domain. After inquiries and votes carried out in accordance with the rules of AECMA-STAN defined in AECMA- STANS General Process Manual, this st

9、andard has received approval for Publication. Contents Page 1 Scope 3 2 Normative references . 3 3 Definitions . 4 Required characteristics 4.1 Dimensions, mass 4.2 Material . 4.3 Main general characteristics 5 Designation 6 Marking . 7 Technical specification 3 3 3 7 7 7 7 7 Copyright Association E

10、uropeene des Constructeurs de Materiel Aerospatial Provided by IHS under license with AECMANot for ResaleNo reproduction or networking permitted without license from IHS-,-,-Page 3 prEN 3545-007:2004 1 Scope This standard specifies cable clamp in the family of rectangular electrical connectors with

11、sealed and non-sealed rear, plastic housing, locking device, for operating temperatures from - 55 “C to 175 “C. 2 Normative references This European Standard incorporates by dated or undated reference, provisions from other publications. These normative references are cited at the appropriate places

12、 in the text and the publications are listed hereafter. For dated references, subsequent amendments to or revisions of any of these publications apply to this European Standard only when incorporated in it by amendment or revision. For undated references the latest edition of the publication referre

13、d to applies (including amendments). EN 3545-001 , Aerospace series - Connectors, electrical, rectangular, with sealed and non-sealed rear, plastic housing, locking device, operating temperatures - 55 “C to 175 “C - Part 001: Technical specification EN 3545-002, Aerospace series - Connectors, electr

14、ical, rectangular, with sealed and non-sealed rear, plastic housing, locking device, operating temperatures - 55 “C to 175 “C - Part 002: Specification of performance and contact arrangements ) 3 Definitions See EN 3545-001. 4 Required characteristics 4.1 Dimensions, mass The dimensions of attachmen

15、t system are given in Figure 1, Figure 2 or Figure 3. Dimensions and tolerances are in millimetres. Mass: 6 g max. for model Code D 9 g max. for model Code E 12 g max. for model Code G 1) Published as AECMA Prestandard at the date of publication of this standard Copyright Association Europeene des C

16、onstructeurs de Materiel Aerospatial Provided by IHS under license with AECMANot for ResaleNo reproduction or networking permitted without license from IHS-,-,-Page 4 prEN 3545-007:2004 Model Code D General tolerance: k 0,2 Figure 1 - Dimensions of model Code D Copyright Association Europeene des Co

17、nstructeurs de Materiel Aerospatial Provided by IHS under license with AECMANot for ResaleNo reproduction or networking permitted without license from IHS-,-,-Page 5 prEN 3545-007:2004 Model Code E General tolerance: k 0,2 Figure 2 - Dimensions of model Code E Copyright Association Europeene des Con

18、structeurs de Materiel Aerospatial Provided by IHS under license with AECMANot for ResaleNo reproduction or networking permitted without license from IHS-,-,-Page 6 prEN 3545-007:2004 Model code G General tolerance: k 0,2 NOTE This backshell can be used only with cable gauge 26 to 12 Figure 3 - Dime

19、nsions of model Code G Copyright Association Europeene des Constructeurs de Materiel Aerospatial Provided by IHS under license with AECMANot for ResaleNo reproduction or networking permitted without license from IHS-,-,-Page 7 prEN 3545-007:2004 Description block CABLE CLAMP 4.2 Material Material: t

20、hermoplastic resin 4.3 Main general characteristics See EN 3545-002. Identity block E N3545-007SC D Number of this standard w- NOTE If necessary, the code 19005 shall be placed between the description block and the identity block. 6 Marking Unless there are other specific contractual requirements, t

21、he marking shall include: - the identity block as defined in 5; - the manufacturers name or trademark. 7 Technical specification See EN 3545-001. Copyright Association Europeene des Constructeurs de Materiel Aerospatial Provided by IHS under license with AECMANot for ResaleNo reproduction or networking permitted without license from IHS-,-,-