AECMA PREN 3645-007-2005 Aerospace series Connectors electrical circular scoop-proof triple start threaded coupling operating temperature 175 degrees C or 200 degrees C continuous .pdf

1、ASD STANDARD NORME ASD ASD NORM prEN 3645-007 Edition P1 November 2005 PUBLISHED BY THE AEROSPACE AND DEFENSE INDUSTRIES ASSOCIATION OF EUROPE - STANDARDIZATION Gulledelle 94 - B-1200 Brussels - Tel. + 32 2 775 8126 - Fax. + 32 2 763 3565 - www.asd-stan.orgICS: 49.060 Descriptors: ENGLISH VERSION Ae

2、rospace series Connectors, electrical, circular, scoop-proof, triple start threaded coupling operating temperature 175 C or 200 C continuous Part 007: Protective cover for plug Product standard Srie arospatiale Connecteurs lectriques circulaires contacts protgs, accouplement par filetage pas rapide

3、trois filets, tempratures dutilisation 175 Cou 200C continu Partie 007 : Bouchon de vol pour fiche Norme de produit Luft- und Raumfahrt Elektrische Rundsteckverbinder, kontaktgeschtzt, Drei-gangige Gewinde-Schnellkupplung Dauerbetriebstemperaturen 175 C oder 200 C Teil 007: Schutzkappe fr freien Ste

4、ckverbinder Produktnorm This “Aerospace Series“ Prestandard has been drawn up under the responsibility of ASD-STAN (The Aerospace and Defense Industries Association of Europe - Standardization). It is published for the needs of the European Aerospace Industry. It has been technically approved by the

5、 experts of the concerned Domain following member comments. Subsequent to the publication of this pre-standard, the technical content shall not be changed to an extent that interchangeability is affected, physically or functionally, without re-identification of the standard. After examination and re

6、view by users and formal agreement of ASD-STAN, it will be submitted as a draft European Standard (prEN) to CEN (European Committee for Standardization) for formal vote and transformation to full European Standard (EN). The CEN national members have then to implement the EN at national level by givi

7、ng the EN the status of a national standard and by withdrawing any national standards conflicting with the EN. Edition approved for publication 30 November 2005 Comments should be sent within six months after the date of publication to ASD-STAN Electrical Domain Copyright 2005 by ASD-STAN Copyright

8、Association Europeene des Constructeurs de Materiel Aerospatial Provided by IHS under license with AECMANot for ResaleNo reproduction or networking permitted without license from IHS-,-,-Page 2 prEN 3645-007:2005Foreword This standard was reviewed by the Domain Technical Coordinator of ASD-STANs Ele

9、ctrical Domain. After inquiries and votes carried out in accordance with the rules of ASD-STAN defined in ASD-STANs General Process Manual, this standard has received approval for Publication. Contents Page 1 Scope3 2 Normative references.3 3 Terminology3 4 Required characteristics 4 4.1 Dimensions,

10、 weights.4 4.2 Materials and surface treatment5 4.3 Electrical, mechanical and climatic characteristics5 5 Designation5 6 Marking.6 7 Technical specification 6 Copyright Association Europeene des Constructeurs de Materiel Aerospatial Provided by IHS under license with AECMANot for ResaleNo reproduct

11、ion or networking permitted without license from IHS-,-,-Page 3 prEN 3645-007:2005 1 Scope This standard specifies the charateristics of protective covers for plugs in the family of circular, electrical connectors, with triple start threaded coupling. It applies to models in table 2. For plugs, see

12、EN 3645-008, EN 3645-011 and EN 3645-012. These connectors are derived from and interchangeable with models W, F and K in specification MIL-DTL-38999/32. 2 Normative references This European Standard incorporates by dated or undated reference provisions from other publications. These normative refer

13、ences are cited at the appropriate places in the text and the publications are listed hereafter. For dated and undated references, subsequent amendments to or revisions of any of these publications apply to this European Standard only when incorporated in it by amendment or revision. For undated ref

14、erences the latest edition of the publication referred to applies. EN 3645-001, Aerospace series - Connectors electrical, circular, scoop-proof, triple start threaded coupling, operating temperature 175 C or 200 C continuous - Part 001: Technical specification 1) EN 3645-002, Aerospace series - Conn

15、ectors electrical, circular, scoop-proof, triple start threaded coupling, operating temperature 175 C or 200 C continuous - Part 002: Specification of performance and contact arrangements 1)EN 3645-008, Aerospace series - Connectors electrical, circular, scoop-proof, triple start threaded coupling,

16、operating temperature 175 C or 200 C continuous - Part 008: Non release plug with grounding ring - Product standard 1)EN 3645-011, Aerospace series - Connectors electrical, circular, scoop-proof, triple start threaded coupling,operating temperature 175 C or 200 C continuous - Part 011: Lanyard relea

17、se plug with grounding fingers - Type 1 - Product standard 1)EN 3645-012, Aerospace series - Connectors electrical, circular, scoop-proof, triple start threaded coupling, operating temperature 175 C or 200 C continuous - Part 012: Lanyard release plug with grounding fingers - Type 2 - Product standa

18、rd 1)MIL-DTL-38999/32, Connectors, electrical, circular, cover, protective, plug, series III, metric 2)3 Terminology See EN 3645-001. 1)Published as AECMA Prestandard at the date of publication of this standard 2)Published by: Department of Defense (DOD), The Pentagon, Washington D.C. 20301 USA Copy

19、right Association Europeene des Constructeurs de Materiel Aerospatial Provided by IHS under license with AECMANot for ResaleNo reproduction or networking permitted without license from IHS-,-,-Page 4 prEN 3645-007:20054 Required characteristics 4.1 Dimensions, weights Dimensions and tolerances are i

20、n millimetres. Key 1 Seal 2 Attachment type 7 3 Attachment type 0 4 Milling or knurling 5 Thread A Figure 1 Protective cover Copyright Association Europeene des Constructeurs de Materiel Aerospatial Provided by IHS under license with AECMANot for ResaleNo reproduction or networking permitted without

21、 license from IHS-,-,-Page 5 prEN 3645-007:2005 Table 1 Protective cover - Dimensions A - External tread Internal thread - Class 2B Mass g max.External diameter mm Diametre on side mm Diameter at thread end mm B C D Models W and F Model K StainlessShell sizeSee note 1) mm min. max. min. max. min. ma

22、x. max. max. min. Aluminium steel 09 15,6315,83 14,97 15,17 14,05 14,41 23,00 12,50 13,00 12 34 11 18,80 19,01 18,14 18,35 17,23 17,58 26,00 15,75 18,00 13 36 13 0,0381 21,98 22,18 21,32 21,52 20,41 20,76 31,00 19,53 20,00 14 40 15 25,15 25,36 24,49 24,70 23,58 23,94 33,00 22,71 23,00 16 46 17 29,80

23、 30,11 28,99 29,24 27,82 28,28 37,00 25,88 26,00 18 52 19 31,39 31,69 30,58 30,83 29,41 29,87 40,00 28,55 29,00 20 58 21 0,0508 34,56 34,87 33,75 34,01 32,59 33,05 44,00 31,72 32,00 22 64 23 37,74 38,04 36,93 37,18 35,76 36,22 46,00 34,90 34,00 24 70 25 40,91 41,22 40,10 40,36 38,94 39,40 50,00 38,0

24、7 39,00 27 80 1)Sizes for protected threads: it is permissible to increase the maximum limit of the diameters for these sizes by the value given in this column.4.2 Materials and surface treatment See Table 2. 4.3 Electrical, mechanical and climatic characteristics See EN 3645-002. 5 Designation EXAM

25、PLE: Description block PROTECTIVE COVER ELECTRICAL CONNECTOR Identity block EN3645-F4B7 Number of the basic standard Model according to Table 2 Protective cover code for plug according to EN 3645-002 Shell size code according to Table 3 Type of attachment according to Figure 1 NOTE: If necessary, th

26、e code I9005 shall be placed between the classification block and the identity block. Copyright Association Europeene des Constructeurs de Materiel Aerospatial Provided by IHS under license with AECMANot for ResaleNo reproduction or networking permitted without license from IHS-,-,-Page 6 prEN 3645-

27、007:2005Table 2 - Model coding Model Description W Protective cover for plug in cadmium-plated aluminium alloy, olive green Salt spray resistance 500 h Maximum operating temperature 175 C continuous F Protective cover for plug in nickel-plated aluminium alloy Maximum operating temperature 200 C cont

28、inuous K Protective cover for plug in stainless steel Maximum operating temperature 200 C continuous Table 3 - Shell size code Shell size Code 09 A 11 B 13 C 15 D 17 E 19 F 21 G 23 H 25 J 6 Marking According to EN 3645-001. 7 Technical specification According to EN 3645-001. Copyright Association Europeene des Constructeurs de Materiel Aerospatial Provided by IHS under license with AECMANot for ResaleNo reproduction or networking permitted without license from IHS-,-,-