AECMA PREN 4045-1994 Aerospace Series Heat Resisting Alloys Capillary Tubes Seamless Diameter 0 6 mm Less Than or Equal to D Less Than or Equal to 2 mm Dimension Edition P1《航空航天系列抗.pdf

1、CEN PREN*4045 94 m 3404587 0074704 057 AECMA STANDARD NORME AECMA AECMA NORM prEN 4045 Edition P 1 September 1994 DITE PAR LASSOCIATION EUROPENNE DES CONSTRUCTEURS DE MATRIEL AROSPATIAL Technopolis - 175, rue Jean-Jacques Rousseau - F-92138 Issy-les-Moulineaux Cedex - Tl. (1) 47.36.98.76 UDC : Descr

2、iptors : ENGLISH VERSION Aerospace series Heat resisting alloys Capillary tubes, seamless Diameter 0,6 mm I D I 2 mm Dimensions Srie arospatiale Alliages rsistant chaud Tubes capillaires sans soudure Diamtres 0.6 mm I D I 2 mm Dimensions Luft- und Raumfahrt Hochwarmfesten Legierungen Kapillarrohre,

3、nahtlos Durchmesser 0,6 mm I D I 2 mm Mae This “Aerospace Series Prestandard has been drawn up under the responsibility of AECMA (Association Europenne des Constructeurs de Matriel Arospatial). It is published on green paper for the needs of AECMA-Members. It has been technically approved by the exp

4、erts of the concerned Technical Committee follo wing comment by the Member countries. Subsequent to the publication of this prestandard, the technical content shall not be changed to an extent that interchangeability is affected, physically or functionally, without re-identification of the standard.

5、 After examination and signature of the AECMA Standard Checking Centre (NPSI and formal agreement of the Official Services of the Member countries it will be submitted as a draft European Standard to CEN (European Committee for Standardization) for formal vote. Nota - Extra copies can be supplied by

6、 B.N.A.E. - Technopolis 54 - 199, rue Jean-Jacques Rousseau - 921 38 ISSY-LES-MOULINEAUX CEDEX Edition approved for publication 1994-09-30 Comments should be sent within six months after the date of publication to AECMA Technopolis - 175, rue Jean-Jacques Rousseau 921 38 Issy-les-Moulineaux Cedex -

7、FRANCE C6 Chairman Mr Grgoire aecma 1994 Copyright Association Europeene des Constructeurs de Materiel Aerospatial Provided by IHS under license with AECMANot for ResaleNo reproduction or networking permitted without license from IHS-,-,-CEN PRENx4045 94 = 3404589 0074705 T93 W Page 3 prEN 4045 : 19

8、94 1 Scope This standard specifies the dimensions and tolerances of capillary tubes, seamless in heat resisting alloys, diameter 0,6 mm I D I 2 mm, for aerospace applications. 2 Normatives referen ces This European Standard incorporates by dated or undated reference provisions from other publication

9、s. These normative references are cited at the appropriate places in the text and the publications are listed hereafter. For dated references, subsequent amendments to or revisions of any of these publications apply to this European Standard only when incorporated in it by amendment or revision. For

10、 undated references the latest edition of the publication referred to applies. EN 2600 EN 3848 Aerospace series - Semi-finished metallic products - Method of measuring for form Aerospace series - Designation of metallic semi-finished products - Rules deviations Aerospace series - Relationship betwee

11、n dimensional standards and material standards 2, TR 241 O 3 Required characteristics 3.1 Form See figure 1 Figure 1 Published as AECMA Prestandard at the date of publication of this standard *) Published as AECMA Technical Report at the date of publication of this standard Previous page is blank Co

12、pyright Association Europeene des Constructeurs de Materiel Aerospatial Provided by IHS under license with AECMANot for ResaleNo reproduction or networking permitted without license from IHS-,-,-CEN PRENx4045 94 3404589 O074706 92T D Nominal mm 096 03 1 ,o 12 1,4 1.6 Page 4 prEN 4045 : 1994 Linear m

13、ass 1) in g/m for a nominal mm : 0,1 092 i ,32 1,85 2,3a 4,22 2,90 5,28 6,33 7.39 3.2 Dimensions 3.2.1 Diameter, thickness and mass See table 1 2,o Table 1 1 9,50 Length Tolerances I 3.2.2 Length t 2 500 500 5000 3.3.1 Diameter +io O See figure i 3.3.2 Thickness See figure 1 3.3.3 Length See table 2

14、 Table 2 Copyright Association Europeene des Constructeurs de Materiel Aerospatial Provided by IHS under license with AECMANot for ResaleNo reproduction or networking permitted without license from IHS-,-,- CEN PREN*4045 94 = 3404587 0074707 bhb W 0,6 2 D I2 Page 5 prEN 4045 : 1994 0,17 % Xi 3.4 Geo

15、metric toleran ces straightness 3.4.1 Method of measurement See EN 3848 3.4.2 Tolerances See table 3 Table 3 Dimensions in millimetres 1 Y, max. 1 Diameter I 3.5 Materials See TR 241 O 4 Designation See EN 2600 Copyright Association Europeene des Constructeurs de Materiel Aerospatial Provided by IHS under license with AECMANot for ResaleNo reproduction or networking permitted without license from IHS-,-,-