AECMA PREN 4165-023-2003 Aerospace series Connectors electrical rectangular modular Operating temperature 175 Degrees C continuous Part 023 Tooling for assembly of receptacle codin.pdf

1、AECMA STANDARD NORME AECMA AECMA NORM Edition approved for publication 28 February 2003 prEN 41 65-023 Edition P 1 February 2003 Comments should be sent within six months after the date of publication to Electrical Domain AECMA-STAN ICs: 49.060 Descriptors: ENGLISH VERSION Aerospace series Connector

2、s, electrical, rectangular, modular Operating temperature 175 OC continuous Part 023: Tooling for assembly of receptacle coding component Product standard Srie arospatiale Luft- und Raumfahrt Connecteurs lectriques rectangulaires Elektrischer Rechtecksteckverbinder Temprature dutilisation 175 OC con

3、tinu Betriebstemperatur 175 OC konstant Partie 023 : Outils de serrage Teil 023: Montageschlsse fr de la clef de dtrompage das Kodierungssystem fr feste Steckverbinder modulaires in modularer Bauweise Norme de produit Produktnorm This “Aerospace Series“ Prestandard has been drawn up under the respon

4、sibility of AECMA-STAN (The European Association of Aerospace Industries - Standardization). It is published on green paper for the needs of the European Aerospace Industry. It has been technically approved by the experts of the concerned Domain following member comments. Subsequent to the publicati

5、on of this Prestandard, the technical content shall not be changed to an extent that interchangeability is affected, physically or functionally, without re-identification of the standard. After examination and review by users and formal agreement of AECMA-STAN it will be submitted as a draft Europea

6、n Standard to CEN (European Committee for Standardization) for formal vote. Copyright Association Europeene des Constructeurs de Materiel Aerospatial Provided by IHS under license with AECMANot for ResaleNo reproduction or networking permitted without license from IHS-,-,-Page 2 prEN 4165-023: 2003

7、Foreword This standard was reviewed by the Domain Technical Coordinator of AECMA-STANS Electrical Domain. After inquiries and votes carried out in accordance with the rules of AECMA-STAN defined in AECMA- STANS General Process Manual, this standard has received approval for Publication. Contents Pag

8、e 1 Scope 2 Normative references . 3 Terminology 4 Required characteristics 5 Tooling for assembly coding component . 6 Designation . 7 Marking . 8 Technical specification Copyright Association Europeene des Constructeurs de Materiel Aerospatial Provided by IHS under license with AECMANot for Resale

9、No reproduction or networking permitted without license from IHS-,-,-Page 3 prEN 4165-023: 2003 1 Scope This standard defines the tooling for assembly of receptacle coding component used in the family of rectangular electrical connectors. 2 Normative references This European Standard incorporates by

10、 dated or undated reference provisions from other publications. These normative references are cited at the appropriate places in the text and the publications are listed hereafter. For dated references, subsequent amendments to or revisions of any of these publications apply to this European Standa

11、rd only when incorporated in it by amendment or revision. For undated references the latest edition of the publication referred to apply. EN 2424, EN 41 65-001, Aerospace series - Marking of aerospace products Aerospace series - Connectors, electrical, rectangular, modular - Operating temperature I7

12、5 “C continuous - Part 001: Technical specification - Product standard 1 ) 3 Term in ol ogy See EN 4165-001. 4 Required characteristics Dimensions are in millimetres. 5 See Figure 1. Tooling for assembly coding component Figure 1 1) Published as AECMA standard at the date of publication of this stan

13、dard Copyright Association Europeene des Constructeurs de Materiel Aerospatial Provided by IHS under license with AECMANot for ResaleNo reproduction or networking permitted without license from IHS-,-,-Page 4 prEN 4165-023: 2003 Description block INSERTION EXTRACTION TOOL FOR REMOVAL MODULES 6 Desig

14、nation EXAMPLE: Identity block EN41 65TC Number of the basic standard a- T: tool 7 Marking Unless there are other specific contractual requirements, the marking shall be in accordance with EN 2424, category P. 8 See EN 4165-001. Tech n i cal specification Copyright Association Europeene des Constructeurs de Materiel Aerospatial Provided by IHS under license with AECMANot for ResaleNo reproduction or networking permitted without license from IHS-,-,-