AECMA PREN 4202-2003 Aerospace Series Aluminium Alloy AL-P6082-T651 Plate 6 mm Less Than a Less Than or Equal to 25 mm Edition P 2《航空航天系列.铝合金AL-P6082-T651金属板6mm小于或等于a小于或等于25mm.P2版》.pdf

1、AECMA STANDARD NORME AECMA AECMA NORM Edition approved for publication 14 March 2003 prEN 4202 Edition P 2 March 2003 Comments should be sent within six months after the date of publication to AECMA-STAN ICs: Descriptors: Supersedes edition P 1 June 1995 ENGLISH VERSION Aerospace series Al um i ni u

2、m alloy AL-P6082- T651 Plate 6 mm a 25 mm Srie arospatiale Alliage daluminium AL-P6082- T651 Tles paisses 6 mm a I 25 mm Luft- und Raumfahrt Aluminiumlegierung AL-P6082- T651 Platten 6 mm ai 25 mm This “Aerospace Series“ Prestandard has been drawn up under the responsibility of AECMA-STAN (The Europ

3、ean Association of Aerospace Industries - Standardization). It is published on green paper for the needs of the European Aerospace Industry. It has been technically approved by the experts of the concerned Domain following member comments. Subsequent to the publication of this Prestandard, the techn

4、ical content shall not be changed to an extent that interchangeability is affected, physically or functionally, without re-identification of the standard. After examination and review by users and formal agreement of AECMA-STAN it will be submitted as a draft European Standard to CEN (European Commi

5、ttee for Standardization) for formal vote. Metallic Material Domain I I Copyright 2003 O by AECMA-STA1 Copyright Association Europeene des Constructeurs de Materiel Aerospatial Provided by IHS under license with AECMANot for ResaleNo reproduction or networking permitted without license from IHS-,-,-

6、Page 2 prEN 4202: 2003 Foreword This standard was reviewed by the Domain Technical Coordinator of AECMA-STANS Metallic Material Domain. After inquiries and votes carried out in accordance with the rules of AECMA-STAN defined in AECMA- STANS General Process Manual, this standard has received approval

7、 for Publication. Copyright Association Europeene des Constructeurs de Materiel Aerospatial Provided by IHS under license with AECMANot for ResaleNo reproduction or networking permitted without license from IHS-,-,-Page 3 prEN 4202: 2003 O Introduction This standard is part of the series of EN metal

8、lic material standards for aerospace applications. The general organization of this series is described in EN 4258. This standard has been prepared in accordance with EN 4500-2. 1 Scope This standard specifies the requirements relating to: Aluminium alloy AL-P6082- T651 Plate 6 mm a 25 mm for aerosp

9、ace application. 2 Normative references This European Standard incorporates by dated or undated refere ce provisia s from other publicatic S. These normative references are cited at the appropriate places in the text and the publications are listed hereafter. For dated references, subsequent amendme

10、nts to or revisions of any of these publications apply to this European Standard only when incorporated in it by amendment or revision. For undated references the latest edition of the publication referred to applies. EN 4258, Aerospace series - Metallic materials - General organization of standardi

11、zation - Links between types of EN standards and their use EN 4400-1, Aerospace series - Aluminium and aluminium alloy wrought products - Technical specification - Part I: Plate 1) EN 4500-2, Aerospace series - Metallic materials - Rules for drafting and presentation of material standards - Part 2:

12、Specific rules for aluminium, aluminium alloys and magnesium alloys 1) 1) Published as AECMA Prestandard at the date of publication of this standard Copyright Association Europeene des Constructeurs de Materiel Aerospatial Provided by IHS under license with AECMANot for ResaleNo reproduction or netw

13、orking permitted without license from IHS-,-,-Page 4 prEN 4202: 2003 si 0,7 1,3 Others Each Total Fe Cu Mn Mg Cr Zn Ti AI - - 0,40 0,6 - - - - - 0,50 0,lO 1,0 1,2 025 020 0,lO 0,05 0,15 Base Form Method of production Limit dimension(s) mm Technical specification Plate Rolled 6a25 EN 4400-1 Heat trea

14、tment Dimensions concerned mm Use condition. 6 a 12,5 123 a 25 Thickness of cladding on each face % - - Hardness Shear strength R, MPa Bending k- - - - - Elongation Rupture stress a% - oR MPa - Elongation at rupture A % - Notes (see line 98) - Aluminium alloy AL-P6082- I Material designation Chemica

15、l composition % Element I I min. I max. - Method of melting I I T651 I T451 I 3.1 I Delivery condition Heat treatment 525 OC e so OC 1 WQ e 40 OC + 1,5 % controlled stretched 3 % + O= ambientlt 25 d 525 OC e so OC 1 WQ e 40 OC + 1,5 % controlled stretched 3 % + 160 “C 6% 186 “C I4 h t 16 h I K I U I

16、 3.2 I Delivery condition code I T651 I T651 I 7 I Use condition Delivery condition Delivery condition + 160 “C 6% 186 “C I4 h t 16 h Heat treatment Characteristics - 3.1 3.2 3.3 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 25 26 27 - - - - - - - - - - - - - - - - - - - - - - Test sample(s) I See

17、EN 4400-1. Test piece(s) I See EN 4400-1. LT I LT I Direction of test piece Ambient I Temperature I 0 I “C I Ambient Strength I Rm I MPal 2 300 I 2 295 Elongation I A I % I hmm 2 8 I 28 Reductionofarea Z % - - Impact strength I I Temperature I 0 I “C I - I Time Ihl Copyright Association Europeene de

18、s Constructeurs de Materiel Aerospatial Provided by IHS under license with AECMANot for ResaleNo reproduction or networking permitted without license from IHS-,-,-Page 5 prEN 4202: 2003 - ixternal defects See EN 4400-1. nternal defects 3atch uniformity 7 Marking inspection Iimensional inspection MSl

19、m 24,5 (typical value) 27,O (typical value) Electrical conductivity Y Votes - - rypical use See EN 4400-1. See EN 4400-1. -I See EN 4400-1. See EN 4400-1. -I 51 - I T451 I T651 -I -I Copyright Association Europeene des Constructeurs de Materiel Aerospatial Provided by IHS under license with AECMANot

20、 for ResaleNo reproduction or networking permitted without license from IHS-,-,-100 See EN 4400-1. Qualification programme to be agreed between manufacturer and purchaser. Page 6 prEN 4202: 2003 - Product qualification Copyright Association Europeene des Constructeurs de Materiel Aerospatial Provided by IHS under license with AECMANot for ResaleNo reproduction or networking permitted without license from IHS-,-,-