ImageVerifierCode 换一换
格式:PDF , 页数:10 ,大小:287.99KB ,
资源ID:421189      下载积分:5000 积分
快捷下载
登录下载
邮箱/手机:
温馨提示:
如需开发票,请勿充值!快捷下载时,用户名和密码都是您填写的邮箱或者手机号,方便查询和重复下载(系统自动生成)。
如填写123,账号就是123,密码也是123。
特别说明:
请自助下载,系统不会自动发送文件的哦; 如果您已付费,想二次下载,请登录后访问:我的下载记录
支付方式: 支付宝扫码支付 微信扫码支付   
注意:如需开发票,请勿充值!
验证码:   换一换

加入VIP,免费下载
 

温馨提示:由于个人手机设置不同,如果发现不能下载,请复制以下地址【http://www.mydoc123.com/d-421189.html】到电脑端继续下载(重复下载不扣费)。

已注册用户请登录:
账号:
密码:
验证码:   换一换
  忘记密码?
三方登录: 微信登录  

下载须知

1: 本站所有资源如无特殊说明,都需要本地电脑安装OFFICE2007和PDF阅读器。
2: 试题试卷类文档,如果标题没有明确说明有答案则都视为没有答案,请知晓。
3: 文件的所有权益归上传用户所有。
4. 未经权益所有人同意不得将文件中的内容挪作商业或盈利用途。
5. 本站仅提供交流平台,并不能对任何下载内容负责。
6. 下载文件中如有侵权或不适当内容,请与我们联系,我们立即纠正。
7. 本站不保证下载资源的准确性、安全性和完整性, 同时也不承担用户因使用这些下载资源对自己和他人造成任何形式的伤害或损失。

版权提示 | 免责声明

本文(AECMA PREN 4235-1-1994 Aerospace Series Steel Wrought Products Technical Specification Part 1 General Requirements Edition P 1《航空航天系列.钢锻制品技术规范.第1部分 一般规定 P.第1版》.pdf)为本站会员(rimleave225)主动上传,麦多课文库仅提供信息存储空间,仅对用户上传内容的表现方式做保护处理,对上载内容本身不做任何修改或编辑。 若此文所含内容侵犯了您的版权或隐私,请立即通知麦多课文库(发送邮件至master@mydoc123.com或直接QQ联系客服),我们立即给予删除!

AECMA PREN 4235-1-1994 Aerospace Series Steel Wrought Products Technical Specification Part 1 General Requirements Edition P 1《航空航天系列.钢锻制品技术规范.第1部分 一般规定 P.第1版》.pdf

1、CEN PREN*4235 PART*l 94 = 3404587 0062762 T7h m AECMA STANDARD prEN 4235 NORME AECMA Part 1 Edition P 1 February 1994 AECMA NORM DIT PAR LASSOCIATION EUROPENNE DES CONSTRUCTEURS DE MATRIEL AROSPATIAL Technopolis - 175, rue Jean-Jacques Rousseau - F-92138 Issy-les-Moulineaux Cedex - Tl. (1) 47.36.98.

2、76 UDC : Descriptors : ENGLISH VERSION Aerospace series Steel Wrought products Technical specification Part 1 : General requirements Srie arospatiale Acier Produits corroys Spcification technique Partie 1 : Exigences gnrales Luft- und Raumfahrt Stahl Umgeformte Erzeugnisse Technische Lieferbedingung

3、en Teil 1 : Allgemeine Anforderungen This “Aerospace Series“ Prestandard has been drawn up under the responsibility of AECMA (Association Europenne des Constructeurs de Matriel Arospatial). It is published on green paper for the needs of AECMA-Members. It has been technically approved by the experts

4、 of the concerned Technical Committee foil0 wing comment by the Member countries. Subsequent to the publication of this prestandard, the technical content shall not be changed to an extent that interchangeability is affected, physically or functionally, without re-identification of the standard. Aft

5、er examination and signature of the AECMA Standard Checking Centre (NPS) and formal agreement of the Official Services of the Member countries it will be submitted as a draft European Standard to CEN (European Committee for Standardization) for formal vote. Nota - Extra copies can be supplied by B.N

6、.A.E. - Technopolis 54 - 199, rue Jean-Jacques Rousseau - 921 38 ISSY-LES-MOULINEAUX CEDEX Comments should be sent within six months after the date of publication to AECMA Technopolis - 175, rue Jean-Jacques Rousseau 921 38 Issy-les-Moulineaux Cedex - FRANCE C5 Chairman M. Odorico Edition approved f

7、or publication 1994-02-28 aecma 1994 Copyright Association Europeene des Constructeurs de Materiel Aerospatial Provided by IHS under license with AECMANot for ResaleNo reproduction or networking permitted without license from IHS-,-,-CEN PREN*4235 PARTUL 9Lt m 340Li589 00b2763 902 m Page 2 prEN 4235

8、-1 : 1994 Contents list 1 2 3 4 5 6 7 8 9 10 11 12 13 Scope Normative references Definitions Quality assurance Manufacture Traceability Freedom from defects Testing Marking Acceptance Inspection and test report Packing Wording of orders 4 Copyright Association Europeene des Constructeurs de Materiel

9、 Aerospatial Provided by IHS under license with AECMANot for ResaleNo reproduction or networking permitted without license from IHS-,-,-CEN PREN*4235 PART* 6 mm, supplied with sheared or sawn edges. 3.11 Section Rolled or extruded product of uniform cross section other than a bar and supplied in str

10、aight lengths. 3.12 Tube Hollow product of uniform thickness supplied in straight lengths. 3.13 Wire Rolled or rolled and drawn product of uniform solid section supplied in coil or on spool. 3.14 Batch A batch consists of products : - of the same form; - - from the same cast; - - - of the same nomin

11、al dimensions, or having the same drawing number; manufactured in the same campaign; in the same heat treatment or metallurgical condition; from the same heat treatment charge or, if approved by the purchaser, from the same heat treatment campaign which shall be specified in the manufacturing schedu

12、le. 3.15 Manufacturer See EN 2000. 3.16 Purchaser Body which purchases the products from a manufacturer or a stockist in accorcmce with the requirements of the user. NOTE : The purchaser may also be the user. 3.17 User See EN 2000. 3.18 Inspection schedule See EN 2078. 3.19 Manufacturing schedule Se

13、e EN 2078. Copyright Association Europeene des Constructeurs de Materiel Aerospatial Provided by IHS under license with AECMANot for ResaleNo reproduction or networking permitted without license from IHS-,-,-CEN PRENa4235 PART*:L 94 3404587 O062767 558 W Selected temperature OC Page 6 prEN 4235-1 :

14、1994 Tolerances OC 3.20 Inspection and test report See EN 2078. 3.21 “Capability clause“ Reference to “capability clause“ signifies that sufficient evidence of a statistical nature with respect to the properties under consideration can be submitted to show that the requirements of the relevant stand

15、ard will be met on the basis of a reduced amount of testing. Such action in no way reduces the obligations of the manufacturer to fulfil all requirements. If subsequent testing indicates that a product does not comply with the requirements, the batch shall be rejected. 4 Quality assurance 4.1 See EN

16、 2000. Approval of the quality system of manufacturers 4.2 Product qualification See material standard. 5 Manufacture 5.1 standard and the applicable part of this standard (EN 4235-2 to EN 4235-5). The product shall be manufactured in accordance with the requirements of the relevant material 5.2 A m

17、anufacturing schedule shall be established and applied in accordance with EN 2078. 5.3 The product shall be supplied in the delivery condition specified in the material standard. If there is more than one delivery condition in the material standard, the condition of supply shall be specified on the

18、order. If a specific temperature (value and tolerance) is stated in the material standard or on the order, that temperature shall be mandatory. If a range is stated, a temperature within that range reduced by the furnace tolerances shall be selected.Unless otherwise specified, the charge shall be ,m

19、aintained at the temperature subject to the tolerances in table 1 for the period stated. Table 1 e 1250 f 15 750 58 5 1250 If a specific time is stated in the material standard or on the order, a tolerance of (O, +20) % shall be applied. Copyright Association Europeene des Constructeurs de Materiel

20、Aerospatial Provided by IHS under license with AECMANot for ResaleNo reproduction or networking permitted without license from IHS-,-,-I CEN PREN*4235 PART*L 94 m 3404589 OOb2b! 494 m Page 7 prEN 4235-1 : 1994 6 Traceability Each product shall be identifiable to its batch at all stages of manufactur

21、e and delivery. 7 Freedom from defects All products shall be free from irregularities not complying with the requirements of the material standard or the order, or prejudicial to the subsequent manufacture or use of the product. Notwithstanding previous acceptance complying with this standard, any p

22、roduct that is found, at a later stage, to contain such defects may be rejected. 8 Testing The tests required by the material standard or the order shall be performed in accordance with the requirements of the appropriate test standard. If a test standard does not exist, the method shall be agreed u

23、pon between the manufacturer and the purchaser. The frequency of testing shall be as specified in EN 4235-2 to EN 4235-5, unless otherwise specified on the order. Where necessary the location and the direction of the test samples shall be specified on the order. 8.1 Chemical composition The chemical

24、 composition shall comply with the requirements of the relevant material standard. The elements which are not specified in the material standard shall not be intentionally added to the steel except for treating the melt before casting. The specified ranges of chemical composition are based on cast a

25、nalysis, any subsequent analytical checks on the product shall take into consideration the heterogenity normal to the steel. Such variations shall be agreed upon between the manufacturer and the purchaser. The chemical composition of each cast shall be determined. Samples for analytical purposes sha

26、ll be representative of the cast. Additionally for remelted products the samples shall be representative for the remelting ingot, taking into account the macro-segregations. The method of analysis shall be at the option of the manufacturers discretion but, in cases of dispute, the method set out in

27、the relevant IS0 standard shall be used. If no IS0 standard exists, an analytical method shall be used that can be calibrated to an accepted reference standard. 8.2 Preparation of the test samples and test pieces Test samples shall not be worked after removal from the product they represent. Test sa

28、mples taken from finally heat treated poducts (use conditions) shall not be further treated. Test samples representing products in a condition other than the condition of use shall be heat treated in accordance with the material standard before testing. Test samples and associated test pieces shall

29、be marked in such a manner that their identity, location and orientation with respect to the product and the batch is maintained. Copyright Association Europeene des Constructeurs de Materiel Aerospatial Provided by IHS under license with AECMANot for ResaleNo reproduction or networking permitted wi

30、thout license from IHS-,-,-CEN PRENx4235 PART*L 94 3404589 0062769 320 Page 8 prEN 4235-1 : 1994 8.3 Special tests Special tests or inspections may be required by the purchaser. In such cases, the nature of test, method, frequency and acceptance criteria shall be specified on the order. 8.4 Retests

31、If any requirement is not met, retests shall be carried out under the following conditions. 8.4.1 If the test procedure or the test piece preparation is faulty, testing shall be re-applied at the original frequency after identification of the cause of failure. When failure cannot be attributed to a

32、faulty test procedure or to test piece preparation, additional identical test samples shall be selected at twice the original frequency. Tensile, impact, creep and creep rupture tests At least one of the samples shall be taken from the product or products with which the original result was obtained

33、(unless already rejected by the manufacturer after suitable identification of the cause of the failure). If all results are satisfactory, the batch shall be accepted. If one or more results are unsatisfactory, the batch shall be, either : - rejected, or - partially or fully reheat treated and tested

34、 as a completely new batch except for chemical composition and inclusion content. 8.4.2 If any test fails to meet the requirement, either : Hardness, bend, flattening and drift test - the remaining products in the batch shall be tested and those which fail be reheat treated and retested as a new bat

35、ch except for chemical composition and inclusion content, or - the entire batch shall be reheat treated and retested as a new batch except for chemical composition and inclusion content. For hardness tests the products with an incorrect value shall be submitted to any alternative procedure agreed up

36、on between the manufacturer and the purchaser. 8.4.3 Metallographic examination If the examination or the test sample preparation is faulty, after identification of the cause of failure, examination shall be re-applied at the original frequency on a test sample located near the first sample. When fa

37、ilure cannot be attribued to a faulty examination or to the tests sample preparation, the batch shall be either : - rejected, or - partially or fully reheat treated if the structure may be corrected by heat treatment, and tested as a new batch except for chemical composition. If the material fails t

38、he cleanness requirements, the product may be cut back before retesting. Copyright Association Europeene des Constructeurs de Materiel Aerospatial Provided by IHS under license with AECMANot for ResaleNo reproduction or networking permitted without license from IHS-,-,-CEN PRENx4235 PART*L 94 m 3404

39、589 0062770 042 m Page 9 prEN 4235-1 : 1994 8.4.4 Other tests For other tests specific to a product, the retest procedure shall be as defined in the relevant part of this standard or on the order. 8.5 Reheat treatment No product or test sample shall be re-hardened or re-solution heat treated more th

40、an once without the agreement of the purchaser. 8.6 Material verification Each product shall be checked at final inspection to ensure that it has been manufactured from the specified material. The method used shall be at the discretion of the manufacturer. 9 Making See : - - - EN 4235-4 for tube; -

41、EN 4235-5 for wire. EN 4235-2 for plate, sheet and strip; EN 4235-3 for bar and section; The method used shall not cause corrosion, crack initiation, contamination or deformation. The frequency of examination adopted by the manufacturer shall be sufficient to permit him to certify compliance with th

42、e requirements. 1 O Acceptance If required, the manufacturer shall inform the purchaser or his chosen agent of the scheduled dates for the extraction of samples and acceptance testing, in order that these operations may be witnessed. I I Inspection and test report The manufacturer shall furnish, wit

43、h each delivery, a report conforming to the requirements of EN 2078 stating the following : - manufacturers name and address; - order number; - material standard number; - delivery condition of products; - description of supplies; - quantity; - cast and batch number; - - inspectors stamp; - batch an

44、d / or test sample heat treatment, if appropriate; results of the mandatory tests, retests and chemical analysis. Copyright Association Europeene des Constructeurs de Materiel Aerospatial Provided by IHS under license with AECMANot for ResaleNo reproduction or networking permitted without license fr

45、om IHS-,-,-CEN PRENb4235 PART*L 94 3404589 O062773 T89 Page 10 prEN 4235-1 : 1994 12 Packing If the purchaser does not specify any particular requirements, the manufacturer shall apply suitable protection to ensure that the products are delivered in a satisfactory condition. The exterior of the pack

46、ing shall bear the following information : - name and address of recipient; - mass; - order number and sufficient information to enable the contents to be related to the relevant documentation. 13 Wording of orders The order shall clearly indicate : quantities to be supplied; dates of delivery; mate

47、rial standard number; delivery condition of products; dimensions and tolerances of products; forwarding address; manufacturing and inspection schedule references; nature and type packing, if required; definition and frequency of any special tests and their retest procedures, if required. Copyright Association Europeene des Constructeurs de Materiel Aerospatial Provided by IHS under license with AECMANot for ResaleNo reproduction or networking permitted without license from IHS-,-,-

copyright@ 2008-2019 麦多课文库(www.mydoc123.com)网站版权所有
备案/许可证编号:苏ICP备17064731号-1