AECMA PREN 4523-1998 Aerospace Series Metallic Materials Test Methods Compression Testing Edition P1《航空航天系列.金属物质试验方法压缩测试.P1版》.pdf

1、 STD-AECMA PREN 4523-ENGL L778 D LOL23Ll 00L552b 5T0 D Nota - Extra copies can be supplied by B.N.A.E. - Technopolis 54 - 199. rue Jean-Jacques Rousseau - 92138 ISSY-LES-MOULINEAUX CEDEX Comments should be sent within six months AECMA Gulledelle 94 Edition approved for publication C5 Chairman Mr Eve

2、tts after the date of publication to 1998-12-31 6-1200 BRUXELLES aecma 1998 AECMA STANDARD prEN 4523 NORME AECMA Edition P 1 AECMA NORM December 1998 PUBLISHED BY THE EUROPEAN ASSOCIATION OF AEROSPACE INDUSTRIES (AECMA) Gulledelle 94 - 8-1200 BRUXELLES - Tel. (+32) 2 775 81 10 - Fax. (+32) 2 775 81

3、11 ICs: I ENGLISH VERSION Aerospace series Metallic materials Test methods Compression testing Srie arospatiale Matriaux mtalliques Mthodes dessais Essai de compression Luft- und Raumfahrt Meta I I isc he Werkstoff e Prfverfahren Druckpruefung This “Aerospace Series“ Prestandard has been drawn up un

4、der the responsibility of AECMA (The European Association of Aerospace Industries). it is published on green paper for the needs of AECMA-Members. It has been technically approved by the experts of the concerned Technical Committee following comment by the Member countries. Subsequent to the publica

5、tion of this frestandard, the technical content shall not be changed to an extent that interchangeability is affected, physically or functionally, without re-identification of the standard. After examination and signature of the AECMA Standard Checking Centre (NPS) and formal agreement of the Offici

6、al Services of the Member countries it will be submitted as a draft European Standard to CEN (European Committee for Standardization) for formal vote. Copyright Association Europeene des Constructeurs de Materiel Aerospatial Provided by IHS under license with AECMANot for ResaleNo reproduction or ne

7、tworking permitted without license from IHS-,-,-STD*AECMA PREN 4523-ENGL 1778 30323LL 0035527 437 Page 2 prEN 4523: 1998 Contents list Introduction . . 3 Scope . . 3 Normative references . 3 Definitions 3 Health and safety 4 Principle . 4 Testing requirements . 4 Test report . . 5 Copyright Associat

8、ion Europeene des Constructeurs de Materiel Aerospatial Provided by IHS under license with AECMANot for ResaleNo reproduction or networking permitted without license from IHS-,-,-STD-AECMA PREN V523-ENGL 1998 I LUL2333 0035528 373 I Page 3 prEN 4523: 1998 O I n trod uc ti on This standard is part of

9、 the series of EN metallic material standards for aerospace applications. The general organization of this series is described in EN 4258. 1 Scope This standard specifies the method of compression testing at ambient temperature of metallic materials for aerospace applications. It shall be applied wh

10、en referred to in the EN technical specification or material standard unless otherwise specified on the drawing, order or inspection schedule. 2 Normative references This European Standard incorporates by dated or undated reference provisions from other publications. These normative references are c

11、ited at the appropriate places in the text and the publications are listed hereafter. For dated references, subsequent amendments to or revisions of any of the publications apply to this European Standard only when incorporated in it by amendments or revision. For undated references the latest editi

12、on of the publication referred to applies. EN 2002-1 EN 4258 EN 4259 EN 10002-2 EN 10002-4 ASTM E4-98 ASTM E9-89a ASTM E83-96 Aerospace series - Metallic materials - Test methods - Part 1: Tensile testing at ambient tem peratu re 1 1 Aerospace series - Metallic materials - General organization of st

13、andardization - Links between types of EN standards and their use Aerospace series - Metallic materials - Definitions of general terms 2) Verification of force measuring system of the tensile testing machine Verification of extensometers used in uniaxial testing Standard Practices for Force Verifica

14、tion of Testing Machines AASHTO No.: T 67 3) Standard test method of compression testing metallic materials at room temperature 3) Standard Practice for Verification and Classification of Extensometers 3) 3 Definitions For the purposes of this standard, the following definitions apply: 3.1 General t

15、erms See EN 4259. 3.2 Other terms See EN 2002-1 and ASTM 9-89a. 1) Published as AECMA Prestandard at the date of publication of this standard 2) In preparation at the date of publication of this standard 3) This standard is published by: American Society for Testing and Materials (ASTM), 100 Barr Ha

16、rbor Dr, West Conshohocken, PA 19428-2959 - USA Copyright Association Europeene des Constructeurs de Materiel Aerospatial Provided by IHS under license with AECMANot for ResaleNo reproduction or networking permitted without license from IHS-,-,-STD=AECMA PREN Y523-ENGL 1978 m LOL23L1 0015529 20T m P

17、age 4 prEN 4523: 1998 4 Health and safety Resources, test pieces, test samples, test materials, test equipment and test procedures shall comply with the current health and safety regulationsllaws of the countries where the test is to be carried out. Where materials and/or reagents which may be hazar

18、dous to health are specified, appropriate precautions in conformity with local regulations and/or laws shall be taken. 5 Principle The test method involves subjecting a test piece to an increasing axial compressive load. 6 Testing requirements 6.1 Resources 6.1.1 Equipmentlplant See ASTM E9-89a. Met

19、ric dimensions shall apply. For references to ASTM E4 (Load verification of testing machines) substitute EN 10002-2. For references to ASTM E83 (Verification and classification of extensometers) substitute EN 100024 6.1.2 Materials/Reagents Materialsheagents included may be suitable: - degreasing fl

20、uids; - recording paper; - means of electronic recording, if appropriate. 6.1.3 Qualification of personnel Testing to the requirements of this test method shall only be undertaken and/or supervised by personnel who have demonstrated their competence by a suitable education and appropiate training an

21、d experience. 6.2 Test samplesTest pieces See ASTM E949a. Metric dimensions shall apply. NOTE: In certain cases the test piece may be the test sample. 6.3 Testing procedure See ASTM E9-89a. Metric dimensions shalt apply. 6.3.1 Temperature of test The test shall be carried out at 10 “C I 0s 35 “C, un

22、less otherwise specified. In cases of dispute the test shall be performed at B= 23 “C f 5 “C. 6.4 Expression of results See ASTM E9-89a. Metric units shall be used. Copyright Association Europeene des Constructeurs de Materiel Aerospatial Provided by IHS under license with AECMANot for ResaleNo repr

23、oduction or networking permitted without license from IHS-,-,-STD.AECMA PREN Li523-ENGL 2778 2012311 0025530 T21 Page 5 prEN 4523: 1998 7 Test report All results shall be in written form and the test report shall include when relevant at least the following information: - reference to this standard;

24、 - any other information relevant to the test method (e.g. test conditions, test equipment, test procedure, verification, .); - identification and traceability to the semi-finished product to be tested in accordance with the technical specifications; - identification and traceability of test samples

25、 taken from the semi-finished product (e.g. location, orientation, size); - identification and traceability of test pieces taken from the test samples (e.g. number, preparation, method, conditioning, use/method of mechanical straightening of coiled wire); - expression of results (e.g. individual val

26、ues or mean values, units, if fracture outside middle third of gauge length, use of an extensometer to measure elongation after fracture, unusual features in the fracture surface, .); - recorded plotslgraphs, when necessary; - date of test; - traceability of individual performing the test; - any incident which may have affected the results; - any deviation from the test method standard. Copyright Association Europeene des Constructeurs de Materiel Aerospatial Provided by IHS under license with AECMANot for ResaleNo reproduction or networking permitted without license from IHS-,-,-