AECMA PREN 4626-002-2006 Aerospace series Connectors optical rectangular multicontact rack and panel Quadrax cavity 2 5 mm diameter ferrule Operating temperatures - 65 Degrees C toP.pdf

1、ASD STANDARD NORME ASD ASD NORM prEN 4626-002 Edition P 1 March 2006 PUBLISHED BY THE AEROSPACE AND DEFENCE INDUSTRIES ASSOCIATION OF EUROPE - STANDARDIZATION Gulledelle 94 - B-1200 Brussels - Tel. + 32 2 775 8126 - Fax. + 32 2 763 3565 - www.asd-stan.orgICS: Descriptors: Aerospace industry, aircraf

2、t, aircraft equipment, optical connector, elements of opticalconnection, optical contact, characteristics, test, quality assurance ENGLISH VERSION Aerospace series Connectors, optical, rectangular, multicontact, rack and panel, Quadrax cavity, 2,5 mm diameter ferrule Operating temperatures 65 C to 1

3、25 C (cable dependent) Flush contacts Part 002: Specification of performance and contact arrangements Srie arospatiale Connecteurs, optique, rectangulaire, contacts multiples, rackables, cavit Quadrax, frule diamtre 2,5 mm Temprature dutilisation 65 C 125 C (selon cble) Contacts affleurants Partie 0

4、02 : Spcification de performances et arrangements des contacts Luft- und Raumfahrt Optische Rechtecksteckverbinder, Quadrax-Kontaktkammer, Durchmesser 2,5 mm Ferrule Betriebstemperaturen 65 C bis 125 C (vom Kabel abhngig) Bndige Kontakte Teil 002: Leistungsdaten und Kontaktanordnungen This “Aerospac

5、e Series“ Prestandard has been drawn up under the responsibility of ASD-STAN (The AeroSpace and Defence Industries Association of Europe - Standardization). It is published for the needs of the European Aerospace Industry. It has been technically approved by the experts of the concerned Domain follo

6、wing member comments. Subsequent to the publication of this Prestandard, the technical content shall not be changed to an extent that interchangeability is affected, physically or functionally, without re-identification of the standard. After examination and review by users and formal agreement of A

7、SD-STAN, it will be submitted as a draft European Standard (prEN) to CEN (European Committee for Standardization) for formal vote and transformation to full European Standard (EN). The CEN national members have then to implement the EN at national level by giving the EN the status of a national stan

8、dard and by withdrawing any national standards conflicting with the EN. Edition approved for publication 31 March 2006 Comments should be sent within six months after the date of publication to ASD-STAN Electrical Domain Copyright 2006 by ASD-STAN Copyright Association Europeene des Constructeurs de

9、 Materiel Aerospatial Provided by IHS under license with AECMA Not for ResaleNo reproduction or networking permitted without license from IHS-,-,-prEN 4626-002:20062 Contents Page Foreword2 1 Scope 3 2 Normative references 3 3 Terms and definitions .3 4 List of product standard .4 5 General characte

10、ristics .4 6 Housing sizes and contact arrangements 4 7 Combination 10 8 Filler plugs and dummy contacts 10 Foreword This standard was reviewed by the Domain Technical Coordinator of ASD-STANs Electrical Domain. After inquiries and votes carried out in accordance with the rules of ASD-STAN defined i

11、n ASD-STANs General Process Manual, this standard has received approval for Publication. Copyright Association Europeene des Constructeurs de Materiel Aerospatial Provided by IHS under license with AECMA Not for ResaleNo reproduction or networking permitted without license from IHS-,-,-prEN 4626-002

12、:2006 3 1 Scope This standard specifies the general characteristics, the conditions for qualification, acceptance and quality assurance, as well as the test programs and groups for fibre sub-assembly contacts in rack and panel connectors, intended for use in a temperature range from 65 C to 125 C co

13、ntinuous (cable dependent). This standard specifies a pair of adaptors to fit with standard Quadrax cavities and EN 4531-101 optical contact. 2 Normative references The following referenced documents are indispensable for the application of this document. For dated references, only the edition cited

14、 applies. For undated references, the latest edition of the referenced document (including any amendments) applies. EN 4531-101, Aerospace series Connectors, optical, circular, single and multipin, coupled by threaded ring Flush contacts Part 101: Optical contact for EN C210A cable 55 C to 125 C Pro

15、duct standard. 1)EN 4626-001, Aerospace series Connectors, optical, rectangular, multicontact, rack and panel, Quadrax cavity, 2,5 mm diameter ferrule Operating temperatures 65 C to 125 C (cable dependent) Flush contacts Part 001: Technical specification. 1)EN 4626-003, Aerospace series Connectors,

16、optical, rectangular, multicontact, rack and panel, Quadrax cavity, 2,5 mm diameter ferrule Operating temperatures 65 C to 125 C (cable dependent) Flush contacts Part 003: Adaptor for plug. 1)EN 4626-004, Aerospace series Connectors, optical, rectangular, multicontact, rack and panel, Quadrax cavity

17、, 2,5 mm diameter ferrule Operating temperatures 65 C to 125 C (cable dependent) Flush contacts Part 004: Adaptor for receptacle. 1)EN 4626-101, Aerospace series Connectors, optical, rectangular, multicontact, rack and panel, Quadrax cavity, 2,5 mm diameter ferrule Operating temperatures 65 C to 125

18、 C (cable dependent) Flush contacts Part 101: Optical contact (sub-assembly) for plug Product standard. 1)EN 4626-201, Aerospace series Connectors, optical, rectangular, multicontact, rack and panel, Quadrax cavity, 2,5 mm diameter ferrule Operating temperatures 65 C to 125 C (cable dependent) Flush

19、 contacts Part 201: Optical contact (sub-assembly) for receptacle Product standard. 1)EN 4626-202, Aerospace series Connectors, optical, rectangular, multicontact, rack and panel, Quadrax cavity, 2,5 mm diameter ferrule Operating temperatures 65 C to 125 C (cable dependent) Flush contacts Part 202:

20、Optical contact assembly for 900 m buffered fibre receptacle Product standard. 1)ARINC 600, Air transport avionics Equipment interfaces. 2)3 Terms and definitions For the purposes of this standard, the terms and definitions given in EN 4626-001 apply. 1) Published as ASD Prestandard at the date of p

21、ublication of this standard. 2) Published by: Aeronautical Radio, Inc. 2551 Riva road, Annapolis, Maryland 21401. Copyright Association Europeene des Constructeurs de Materiel Aerospatial Provided by IHS under license with AECMA Not for ResaleNo reproduction or networking permitted without license f

22、rom IHS-,-,-prEN 4626-002:2006 4 4 List of product standard EN 4626-003, Aerospace series Connectors, optical, rectangular, multicontact, rack and panel, Quadrax cavity, 2,5 mm diameter ferrule Operating temperatures 65 C to 125 C (cable dependent) Flush contacts Part 003: Adaptor for plug. EN 4626-

23、004, Aerospace series Connectors, optical, rectangular, multicontact, rack and panel, Quadrax cavity, 2,5 mm diameter ferrule Operating temperatures 65 C to 125 C (cable dependent) Flush contacts Part 004: Adaptor for receptacle. EN 4626-101, Aerospace series Connectors, optical, rectangular, multic

24、ontact, rack and panel, Quadrax cavity, 2,5 mm diameter ferrule Operating temperatures 65 C to 125 C (cable dependent) Flush contacts Part 101: Optical contact (sub-assembly) for plug Product standard. EN 4626-201, Aerospace series Connectors, optical, rectangular, multicontact, rack and panel, Quad

25、rax cavity, 2,5 mm diameter ferrule Operating temperatures 65 C to 125 C (cable dependent) Flush contacts Part 201: Optical contact (sub-assembly) for receptacle Product standard. EN 4626-202, Aerospace series Connectors, optical, rectangular, multicontact, rack and panel, Quadrax cavity, 2,5 mm dia

26、meter ferrule Operating temperatures 65 C to 125 C (cable dependent) Flush contacts Part 202: Optical contact assembly for 900 m buffered fibre receptacle Product standard. 5 General characteristics 5.1 Climatic characteristics Temperature range: 65 C to 125 C depending on the cable type. Fluid resi

27、stance: Not applicable. Corrosion resistance: 48 hours salt spray. 5.2 Mechanical characteristics Mechanical endurance: 500 mating and unmating cycles. NOTE Any configuration of layout must not exceed the maximum value defined in ARINC 600 specification for mating force. 6 Housing sizes and contact

28、arrangements Rear release/rear removable contact. See Figures 1 to 5. Copyright Association Europeene des Constructeurs de Materiel Aerospatial Provided by IHS under license with AECMA Not for ResaleNo reproduction or networking permitted without license from IHS-,-,-prEN 4626-002:2006 5 Plug front

29、mating face Receptacle front mating face Figure 1 Layout Q11 Copyright Association Europeene des Constructeurs de Materiel Aerospatial Provided by IHS under license with AECMA Not for ResaleNo reproduction or networking permitted without license from IHS-,-,-prEN 4626-002:20066 Plug front mating fac

30、e Receptacle front mating face Figure 2 Layout 11Q2 Copyright Association Europeene des Constructeurs de Materiel Aerospatial Provided by IHS under license with AECMA Not for ResaleNo reproduction or networking permitted without license from IHS-,-,-prEN 4626-002:2006 7 Plug front mating face Recept

31、acle front mating face Figure 3 Layout Q6 Copyright Association Europeene des Constructeurs de Materiel Aerospatial Provided by IHS under license with AECMA Not for ResaleNo reproduction or networking permitted without license from IHS-,-,-prEN 4626-002:20068 Plug front mating face Receptacle front

32、mating face Figure 4 Layout 62Q2 Copyright Association Europeene des Constructeurs de Materiel Aerospatial Provided by IHS under license with AECMA Not for ResaleNo reproduction or networking permitted without license from IHS-,-,-prEN 4626-002:20069 Plug front mating face Receptacle front mating fa

33、ce Figure 5 Layout 68Q2 Copyright Association Europeene des Constructeurs de Materiel Aerospatial Provided by IHS under license with AECMA Not for ResaleNo reproduction or networking permitted without license from IHS-,-,-prEN 4626-002:200610 7 Combination Removable contacts which can be used with t

34、he various types of connectors are defined in the product standards see Table 1. Table 1 Type of sub-assembly (contact + adaptor) Type of contact Type of adaptor Type of connector housing EN cable specification EN 4626-101 EN 4531-101 EN 4626-003 plug C210A101 EN 4626-201 EN 4531-101 EN 4626-004 rec

35、eptacle C210A101 EN 4626-202 areceptacle C210A102 aThis part number included adaptor and dedicated contact which is not removable. 8 Filler plugs and dummy contacts Filler plugs and dummy contact, which will be defined in European standard in preparation, shall be installed in unused cavities. Copyright Association Europeene des Constructeurs de Materiel Aerospatial Provided by IHS under license with AECMA Not for ResaleNo reproduction or networking permitted without license from IHS-,-,-