AECMA PREN 4626-201-2006 Aerospace series Connectors optical rectangular multicontact rack and panel Quadrax cavity 2 5 mm diameter ferrule Operating temperatures - 65 Degrees C toP.pdf

1、ASD STANDARD NORME ASD ASD NORM prEN 4626-201 Edition P 1 March 2006 PUBLISHED BY THE AEROSPACE AND DEFENCE INDUSTRIES ASSOCIATION OF EUROPE - STANDARDIZATION Gulledelle 94 - B-1200 Brussels - Tel. + 32 2 775 8126 - Fax. + 32 2 763 3565 - www.asd-stan.orgICS: Descriptors: Aerospace industry, aircraf

2、t, aircraft equipment, optical connector, elements of opticalconnection, optical contact, characteristics, test, quality assurance ENGLISH VERSION Aerospace series Connectors, optical, rectangular, multicontact, rack and panel, Quadrax cavity, 2,5 mm diameter ferrule Operating temperatures 65 C to 1

3、25 C (cable dependent) Flush contacts Part 201: Optical contact (sub-assembly) for receptacle Product standard Srie arospatiale Connecteurs, optique, rectangulaire, contacts multiples, rackables, cavit Quadrax, frule diamtre 2,5 mm Temprature dutilisation 65 C 125 C (selon cble) Contacts affleurants

4、 Partie 201 : Contact optique (sous-ensemble) pour embase Norme produit Luft- und Raumfahrt Optische Rechtecksteckverbinder, Quadrax-Kontaktkammer, Durchmesser 2,5 mm Ferrule Betriebstemperaturen 65 C bis 125 C (vom Kabel abhngig) Bndige Kontakte Teil 201: Optische Kontakt (Unterbaugruppe) fr festen

5、 Steckverbinder Produktnorm This “Aerospace Series“ Prestandard has been drawn up under the responsibility of ASD-STAN (The AeroSpace and Defence Industries Association of Europe - Standardization). It is published for the needs of the European Aerospace Industry. It has been technically approved by

6、 the experts of the concerned Domain following member comments. Subsequent to the publication of this Prestandard, the technical content shall not be changed to an extent that interchangeability is affected, physically or functionally, without re-identification of the standard. After examination and

7、 review by users and formal agreement of ASD-STAN, it will be submitted as a draft European Standard (prEN) to CEN (European Committee for Standardization) for formal vote and transformation to full European Standard (EN). The CEN national members have then to implement the EN at national level by g

8、iving the EN the status of a national standard and by withdrawing any national standards conflicting with the EN. Edition approved for publication 31 March 2006 Comments should be sent within six months after the date of publication to ASD-STAN Electrical Domain Copyright 2006 by ASD-STAN Copyright

9、Association Europeene des Constructeurs de Materiel Aerospatial Provided by IHS under license with AECMA Not for ResaleNo reproduction or networking permitted without license from IHS-,-,-prEN 4626-201:20062 Contents Page Foreword2 1 Scope 3 2 Normative references 3 3 Optical contact dimensions3 4 P

10、osition of the optical contact in the male adaptor (for receptacle)3 5 Technical specification .4 6 Tests4 7 Assembly process instruction .5 8 Designation 6 Foreword This standard was reviewed by the Domain Technical Coordinator of ASD-STANs Electrical Domain. After inquiries and votes carried out i

11、n accordance with the rules of ASD-STAN defined in ASD-STANs General Process Manual, this standard has received approval for Publication. Copyright Association Europeene des Constructeurs de Materiel Aerospatial Provided by IHS under license with AECMA Not for ResaleNo reproduction or networking per

12、mitted without license from IHS-,-,-prEN 4626-201:2006 3 1 Scope This standard defines the installed dimension information of EN 4531-101 fibre optic contact in the EN 4626-004 receptacle adaptor, together with performance requirements and assembly information based on EN C210A specification (62,5 m

13、/125 m fibre and 1,8 mm outside diameter cable). 2 Normative references The following referenced documents are indispensable for the application of this document. For dated references, only the edition cited applies. For undated references, the latest edition of the referenced document (including an

14、y amendments) applies. EN 2591-100*, Aerospace series Elements of electrical and optical connection Test methods Part 100: General. EN 4531-101, Aerospace series Connectors, optical, circular, single and multipin, coupled by threaded ring Flush contacts Part 101: Optical contact for EN C210A cable 5

15、5 C to 125 C Product standard. 1)EN 4626-001, Aerospace series Connectors, optical, rectangular, multicontact, rack and panel, Quadrax cavity, 2,5 mm diameter ferrule Operating temperatures 65 C to 125 C (cable dependent) Flush contacts Part 001: Technical specification. 1)EN 4626-004, Aerospace ser

16、ies Connectors, optical, rectangular, multicontact, rack and panel, Quadrax cavity, 2,5 mm diameter ferrule Operating temperatures 65 C to 125 C (cable dependent) Flush contacts Part 004: Adaptor for receptacle. 1)ARINC 600, Air transport avionics Equipment interfaces. 2)MIL-I-81969/8B, Installing a

17、nd removal tools, connector electrical contact, types I and II, class 2, composition A. 3)MIL-I-81969/14C, Installing and removal tools, connector electrical contact, type III, class 2, composition B. 3)3 Optical contact dimensions See EN 4531-101. 4 Position of the optical contact in the male adapt

18、or (for receptacle) Optical adaptor is defined in EN 4626-004. See Figure 1. Dimensions are in millimetres. *And all its parts quoted in this standard. 1) Published as ASD Prestandard at the date of publication of this standard. 2) Published by: Aeronautical Radio, Inc. 2551 Riva road, Annapolis, Ma

19、ryland 21401. 3) Published by: Department of Defense (DOD), the Pentagon, Washington, D.C. 20301 USA. Copyright Association Europeene des Constructeurs de Materiel Aerospatial Provided by IHS under license with AECMA Not for ResaleNo reproduction or networking permitted without license from IHS-,-,-

20、prEN 4626-201:2006 4 Key 1 See EN 4531-101. 2 Alignment boot aRear bottoming position bRelaxed position Figure 1 Spring force when connector is mated: Typical: 9 N (minimum 5 N, maximum 13 N). Spring outer diameter shall be 3,95 mm maximum. Add the mass: (0,9 0,2) g. 5 Technical specification See EN

21、 4626-001. 6 Tests 6.1 Tests according to EN 2591-100 Standard See Table 1. 7,4 min. a10,35 max. b1 2Copyright Association Europeene des Constructeurs de Materiel Aerospatial Provided by IHS under license with AECMA Not for ResaleNo reproduction or networking permitted without license from IHS-,-,-p

22、rEN 4626-201:2006 5 Table 1 EN 2591- Designation of the test Details 6101 Visual examination No loosening of parts, cracks, excessive wear, or detached parts. Optical face undamaged and free from contamination when examined at 100 magnification minimum. 102 Examination of dimensions and mass Dimensi

23、ons according to Figure 1 6301 Endurance at temperature 1 000 hours at 125 C 6305 Rapid change of temperature 5 cycles TA= 125 C TB= 55 C 6307 Salt mist 48 hours 6315 Fluid resistance Applicable for no metallic adaptor 6321 Damp heat, cyclic test Connector mated, two cycles method A 6402 Shock Metho

24、d A, severity 50, 11 ms. 6403 Vibrations Method B, Figure 3, Table 2, level E. Two axes (X and Y), 8 hours/axe (checked with ARINC 600) 6406 Mechanical endurance 500 cycles for connector Maintenance ageing: 10 cycles 408 Mating and unmating forces Any configuration of layout must not exceed the maxi

25、mum value defined in ARINC 600 specification for mating force 601 Insertion loss 1 dB maximum during and after test 602 Variation of attenuation and optical discontinuity No optical discontinuity 0,5 s. Threshold at 1 dB 604 Cleaning capability of optical face Applicable 605 Return loss RL 21 dB 6.2

26、 Additional test See EN 4626-001. 7 Assembly process instruction 7.1 Cleaning The connector design allows easy access for cleaning of the optical end faces. With the connectors unmated the process for cleaning should include: 1) With the contacts remaining in the connectors use a lint free tissue or

27、 gleaning prob wetted with a suitable accepted cleaning solution to wipe the end face of the contacts. 2) Remove excess cleaning fluid with aerosol free agent dry air. 3) Mate the connector halves. The cleaning procedure is the same for male and female inserts in either plug or receptacle. Copyright

28、 Association Europeene des Constructeurs de Materiel Aerospatial Provided by IHS under license with AECMA Not for ResaleNo reproduction or networking permitted without license from IHS-,-,-prEN 4626-201:20066 7.2 Tooling 7.2.1 Optical contact No special tools are required for inserting or extracting

29、 the EN 4531-101 contact assemblies into the rear of the connector adaptor. If deemed necessary a MIL-I-81969/14C-12 insert/extract tool may be used. The standard tool as per MIL-I-81969/8-10 standard (P/N for size 12) may be used. 7.2.2 Adaptor For insertion/extraction of the adaptor the insert/ext

30、ract tool defined in ARINC 600 attachment 20 shall be used. 7.3 Assembly instruction Will be defined in Technical Report, in preparation. 8 Designation EXAMPLE Description block CONTACT OPTICAL, SUB-ASSEMBLY Identity block EN4626-201 Number of this standard Copyright Association Europeene des Constructeurs de Materiel Aerospatial Provided by IHS under license with AECMA Not for ResaleNo reproduction or networking permitted without license from IHS-,-,-