AECMA PREN 4639-003-2006 Aerospace series Connectors optical rectangular modular multicontact 1 25 diameter ferrule with removable alignment sleeve holder Part 003 Male optical mod.pdf

1、ASD STANDARD NORME ASD ASD NORM prEN 4639-003 Edition P 1 September 2006 PUBLISHED BY THE AEROSPACE AND DEFENCE INDUSTRIES ASSOCIATION OF EUROPE - STANDARDIZATION Gulledelle 94 - B-1200 Brussels - Tel. + 32 2 775 8126 - Fax. + 32 2 763 3565 - www.asd-stan.orgICS: 49.060 Descriptors: ENGLISH VERSION

2、Aerospace series Connectors, optical, rectangular, modular, multicontact, 1,25 diameter ferrule, with removable alignment sleeve holder Part 003: Male optical module Product standard Srie arospatiale Connecteurs optiques rectangulaires, modulaires multivoies, frule 1,25, quips dun porte sleeve dmont

3、able Partie 003 : Module optique mle Norme de produit Luft- und Raumfahrt Optischer Rechtecksteckverbinder, modular, multipin, Ferrulendurchmesser 1,25 mm, demontierbarer Zentrierhlsenhalter Teil 003: Produktnorm This “Aerospace Series“ Prestandard has been drawn up under the responsibility of ASD-S

4、TAN (The AeroSpace and Defence Industries Association of Europe - Standardization). It is published for the needs of the European Aerospace Industry. It has been technically approved by the experts of the concerned Domain following member comments. Subsequent to the publication of this Prestandard,

5、the technical content shall not be changed to an extent that interchangeability is affected, physically or functionally, without re-identification of the standard. After examination and review by users and formal agreement of ASD-STAN, it will be submitted as a draft European Standard (prEN) to CEN

6、(European Committee for Standardization) for formal vote and transformation to full European Standard (EN). The CEN national members have then to implement the EN at national level by giving the EN the status of a national standard and by withdrawing any national standards conflicting with the EN. E

7、dition approved for publication 30 September 2006 Comments should be sent within six months after the date of publication to ASD-STAN Electrical Domain Copyright 2006 by ASD-STAN Copyright Association Europeene des Constructeurs de Materiel Aerospatial Provided by IHS under license with AECMA Not fo

8、r ResaleNo reproduction or networking permitted without license from IHS-,-,-prEN 4639-003:20062 Contents Page Foreword . 2 1 Scope 3 2 Normative references 3 3 Terms and definitions. 3 4 Required characteristics 3 4.1 Dimensions 3 4.2 Material and surface treatment 6 4.3 Optical, mechanical and cli

9、matic characteristics 6 5 Designation 6 6 Marking. 6 7 Technical specification. 6 Foreword This standard was reviewed by the Domain Technical Coordinator of ASD-STANs Electrical Domain. After inquiries and votes carried out in accordance with the rules of ASD-STAN defined in ASD-STANs General Proces

10、s Manual, this standard has received approval for Publication. Copyright Association Europeene des Constructeurs de Materiel Aerospatial Provided by IHS under license with AECMA Not for ResaleNo reproduction or networking permitted without license from IHS-,-,-prEN 4639-003:20063 1 Scope This standa

11、rd specifies the characteristics of a male optical module for rectangular modular multipin connectors. 2 Normative references The following referenced documents are indispensable for the application of this document. For dated references, only the edition cited applies. For undated references, the l

12、atest edition of the referenced document (including any amendments) applies. EN 2424, Aerospace series Marking of aerospace products. EN 4639-001, Aerospace series Connectors, optical, rectangular, modular, multicontact, 1,25 diameter ferrule, with removable alignment sleeve holder Part 001: Technic

13、al specification. 1) EN 4639-002, Aerospace series Connectors, optical, rectangular, modular, multicontact, 1,25 diameter ferrule, with removable alignment sleeve holder Part 002: List of product standards. 1) EN EPX-001, Aerospace series Connector, electrical, rectangular, modular, rectangular inse

14、rts Operating temperature 175 C continuous Part 001: Technical specification. 2) 3 Terms and definitions For the purposes of this document, the terms and definitions given in EN 4639-001 apply. 4 Required characteristics 4.1 Dimensions 4.1.1 Rectangular connector interface module: Outer Dimensions S

15、ee Figure 1. 1) Published as ASD Prestandard at the date of publication of this standard. 2) In preparation Copyright Association Europeene des Constructeurs de Materiel Aerospatial Provided by IHS under license with AECMA Not for ResaleNo reproduction or networking permitted without license from IH

16、S-,-,-prEN 4639-003:20064 Key Module rear limit stop (on the module retention clip) Module front limit stop (on the shell) 1 Interfacial seal 2 Module front face 3 Rear grommet 4 On ribs 5 R 2,402,60“A“ keying 6 2 R 2,402,60“B“ keying Figure 1 1 2 3 4 4 6 5 1 2 Copyright Association Europeene des Co

17、nstructeurs de Materiel Aerospatial Provided by IHS under license with AECMA Not for ResaleNo reproduction or networking permitted without license from IHS-,-,-prEN 4639-003:20065 4.1.2 Rectangular connector interface module : Optical contact position See Figure 2. Key Module rear limit stop (on the

18、 module retention clip) Module front limit stop (on the shell) Contact rear limit stop (in the module) 1 Interfacial seal operating range 2 Interfacial seal 3 Module front face 4 Rear grommet 5 On ribs Figure 2 1 2 3 1,05 0,65 1 2 3 45 5Copyright Association Europeene des Constructeurs de Materiel A

19、erospatial Provided by IHS under license with AECMA Not for ResaleNo reproduction or networking permitted without license from IHS-,-,-prEN 4639-003:20066 4.2 Material and surface treatment See EN EPX- 001. 4.3 Optical, mechanical and climatic characteristics See EN 4639-002. 5 Designation EXAMPLE D

20、escription block CONNECTOR, OPTICAL Identity bloc EN4639-003EF12A Number of the basic standard Male module Arrangement code (see EN 4639-002) Connector cavity A or B 6 Marking The marking shall include the identification, the date of manufacture (year, week) and the name or trade mark of the manufac

21、turer or conform to standard EN 2424, code P, if required. 7 Technical specification See optical contact product standard. 3) 3) Performance is directly linked to optical contact and fibre technology. Copyright Association Europeene des Constructeurs de Materiel Aerospatial Provided by IHS under license with AECMA Not for ResaleNo reproduction or networking permitted without license from IHS-,-,-