1、ASD STANDARD NORME ASD ASD NORM prEN 4700-002 Edition P 2 July 2009 PUBLISHED BY THE AEROSPACE AND DEFENCE INDUSTRIES ASSOCIATION OF EUROPE - STANDARDIZATIONAvenue de Tervuren, 270 - B-1150 Brussels - Tel. + 32 2 775 8126 - Fax. + 32 2 775 8131 - www.asd-stan.orgICS: Supersede edition P1 of March 20
2、02 Descriptors: ENGLISH VERSION Aerospace series Steel and heat resisting alloys Wrought products Technical specification Part 002: Bar and section Srie arospatiale Aciers et alliages rsistant chaud Produits corroys Spcification technique Partie 002 : Barres et profils Luft- und Raumfahrt Stahl und
3、Hochwarmfesten Legierungen Umgeformte Erzeugnisse Technische Lieferbedingungen Teil 002: Stangen und Profile This “Aerospace Series“ Prestandard has been drawn up under the responsibility of ASD-STAN (The AeroSpace and Defence Industries Association of Europe - Standardization). It is published for
4、the needs of the European Aerospace Industry. It has been technically approved by the experts of the concerned Domain following member comments. Subsequent to the publication of this Prestandard, the technical content shall not be changed to an extent that interchangeability is affected, physically
5、or functionally, without re-identification of the standard. After examination and review by users and formal agreement of ASD-STAN, it will be submitted as a draft European Standard (prEN) to CEN (European Committee for Standardization) for formal vote and transformation to full European Standard (E
6、N). The CEN national members have then to implement the EN at national level by giving the EN the status of a national standard and by withdrawing any national standards conflicting with the EN. Edition approved for publication 31 July 2009 Comments should be sent within six months after the date of
7、 publication to ASD-STAN Metallic Material Domain Copyright 2009 by ASD-STAN Copyright ASD-STAN Provided by IHS under license with AECMA Not for ResaleNo reproduction or networking permitted without license from IHS-,-,-prEN 4700-002:2009 (E) 2 Contents Page Foreword2 Introduction .3 1 Scope 3 2 Nor
8、mative references 3 3 Terms and definitions .5 4 Wording of order5 5 Health and safety .6 6 Technical requirements 6 Foreword This standard was reviewed by the Domain Technical Coordinator of ASD-STANs Metallic Material Domain. After inquiries and votes carried out in accordance with the rules of AS
9、D-STAN defined in ASD-STANs General Process Manual, this standard has received approval for Publication. Copyright ASD-STAN Provided by IHS under license with AECMA Not for ResaleNo reproduction or networking permitted without license from IHS-,-,-prEN 4700-002:2009 (E) 3 Introduction This standard
10、is part of the series of EN metallic material standards for aerospace applications. The general organization of this series is described in EN 4258. 1 Scope This standard defines the requirements for the ordering, manufacture, testing, inspection and delivery of steel and heat resisting alloy bar an
11、d section. It shall be applied when referred to and in conjunction with the EN material standard unless otherwise specified on the drawing, order or inspection schedule. 2 Normative references The following referenced documents are indispensable for the application of this document. For dated refere
12、nces, only the edition cited applies. For undated references, the latest edition of the referenced document (including any amendments) applies. ISO 642, Steel Hardenability test by end quenching (Jominy test) ISO 3651-1, Determination of resistance to intergranular corrosion of stainless steels Part
13、 1: Austenitic and ferritic-austenitic (duplex) stainless steels Corrosion test in nitric acid medium by measurement of loss in mass (Huey test). ISO 3651-2, Determination of resistance to intergranular corrosion of stainless steels Part 2: Ferritic, austenitic and ferritic-austenitic (duplex) stain
14、less steels Corrosion test in media containing sulfuric acid. ISO 3887, Steels Determination of depth of decarburization. EN 2002-1, Aerospace series Metallic materials Test methods Part 001: Tensile testing at ambient temperature. EN 2002-2, Aerospace series Metallic materials Test methods Part 002
15、: Tensile testing at elevated temperature. EN 2002-5, Aerospace series Metallic materials Test methods Part 5: Uninterrupted creep and stress-rupture testing. 1)EN 2002-7, Aerospace series Metallic materials Test methods Part 7: Hardness test. 1)EN 2002-8, Aerospace series Metallic materials Test me
16、thods Part 8: Micrographic determination of grain size.1)EN 2002-16, Aerospace series Metallic materials Test methods Part 16: Non-destructive testing Penetrant testing. 1)EN 2003-7, Aerospace series Steel Test methods Part 7: Macrographic test. 1)1) Published as ASD Prestandard at the date of publi
17、cation of this standard. Copyright ASD-STAN Provided by IHS under license with AECMA Not for ResaleNo reproduction or networking permitted without license from IHS-,-,-prEN 4700-002:2009 (E) 4 EN 2032-1, Aerospace series Metallic materials Part 1: Conventional designation. EN 2032-2, Aerospace serie
18、s Metallic materials Part 2: Coding of metallurgical condition in delivery condition. EN 2078, Aerospace series Metallic materials Manufacturing schedule, inspection schedule, inspection and test report Definition, general principles, preparation and approval. EN 2857-1, Aerospace series Metallic ma
19、terials Test methods for ferromagnetic materials Non-destructive testing Magnetic particle inspection Part 1: General requirements.2)EN 2857-2, Aerospace series Metallic materials Test methods for ferromagnetic materials Non-destructive testing Magnetic particle inspection Part 2: Inspection require
20、ments.2)EN 2950, Aerospace series Test method Wrought heat resisting alloys Semi-finished products and parts Conditions for macrographic and micrographic examination Atlas of structures and defects. EN 2951, Aerospace series Metallic materials Test method Micrographic determination of content of non
21、-metallic inclusions. 1)EN 3874, Aerospace series Test methods for metallic materials Constant amplitude force-controlled low cycle fatigue testing.1)EN 3987, Aerospace series Test method for metallic materials Constant amplitude force-controlled high cycle fatigue testing.1)EN 3988, Aerospace serie
22、s Test methods for metallic materials Constant amplitude strain-controlled low cycle fatigue testing.1)EN 4050-1, Aerospace series Test method for metallic materials Ultrasonic inspection of bars, plates, forging stock and forgings Part 1: General requirements. 1)EN 4050-4, Aerospace series Test met
23、hod for metallic materials Ultrasonic inspection of bars, plates, forging stock and forgings Part 4: Acceptance criteria. 1)EN 4258, Aerospace series Metallic materials General organization of standardization Links between types of EN standards and their use. EN 4259, Aerospace series Metallic mater
24、ials Definition of general terms. 1)EN 4436, Aerospace series Steel Test methods Determination of Delta ferrite content. 1)EN 9100, Aerospace series Quality management systems Requirements (based on ISO 9001:2000) and Quality systems Model for quality assurance in design, development, production, in
25、stallation and servicing (based on ISO 9001:1994). EN 9133, Aerospace series Quality management systems Qualification procedure for aerospace standard parts. 2) In preparation at the date of publication of this standard. Copyright ASD-STAN Provided by IHS under license with AECMA Not for ResaleNo re
26、production or networking permitted without license from IHS-,-,-prEN 4700-002:2009 (E) 5 TR 2410, Aerospace series Metallic materials Relationship between dimensional standards and material standards. 3)EN 10027-1, Designation systems for steels Part 1: Steel names. EN 10045-1, Metallic Materials Ch
27、arpy impact test Part 1: Test method (V- and U-notches). EN 10079, Definition of steel products. AMS 2750, Pyrometry. 4)3 Terms and definitions For the purposes of this document, the terms and definitions given in EN 4259 apply. For definitions specific to steel, see EN 10079. 3.1 batch for heat tre
28、atment using a continuous furnace, a continuous run of less than or equal to 8 hours may be considered as the same heat treatment charge 4 Wording of order The order shall clearly indicate: quantities to be supplied; dates of delivery; material standard number; delivery condition and metallurgical c
29、ode of products; dimensions and tolerances or reference to an appropriate dimensional standard; product designation, when required; forwarding address; nature and type of packing, if required; surface protection, if appropriate; definition and frequency of any special tests and their retest procedur
30、es, if required. 3) Published as an ASD Technical Report at the date of publication of this standard. 4) Published by: American Society for Testing and Materials (ASTM), 100 Barr Harbor Drive, PO Box C700, West Conshohocken, PA, 19428-2959 USA. Copyright ASD-STAN Provided by IHS under license with A
31、ECMA Not for ResaleNo reproduction or networking permitted without license from IHS-,-,-prEN 4700-002:2009 (E) 6 5 Health and safety The product in the delivery condition shall fulfil the current health and safety laws of the area of the country where it is to be delivered. A product safety data she
32、et shall be available. 6 Technical requirements 6.1 General The product shall be manufactured in accordance with the requirements of the relevant material standard and the applicable requirements of this specification. A manufacturing schedule shall be established and applied in accordance with EN 2
33、078. Product shall satisfy the requirements of the material standard and/or order and shall be free from irregularities prejudicial to the subsequent manufacture or use of this product. Notwithstanding previous acceptance complying with this material standard, any product that is found, at a later s
34、tage, to contain such defects shall be rejected. Unless otherwise specified, the requirements in Tables 1 and 2 shall apply in conjunction with those of the relevant material standard. Table 1 relates to lines 1 to 29 (inclusive) of the material standard and Table 2 relates to lines 30 onwards in wh
35、ich the sub-line format is also used. Lines 2 to 98 may also be opened in line 100 if the material standard details specific qualification requirements. If a specific line number is not shown in Tables 1 and 2, the requirement is stated in the material standard and/or order. 6.2 Qualification requir
36、ements Qualification requirements when invoked by the material standard and/or order are detailed in Tables 1 and 2. Unless otherwise agreed between the manufacturer and purchaser the qualification phase shall be run on the first 3 batches, coming from at least 2 casts. 6.3 Release requirements 6.3.
37、1 Release tests Release testing shall be the responsibility of the manufacturer. The purchaser reserves the right to perform any of the inspections and/or tests required by the material standard and/or order. The test samples shall be representative of the product. When required by the order, the ma
38、nufacturer shall inform the purchaser of the planned dates for extraction of samples and release testing in order that these operations may be witnessed. Tables 1 and 2 detail the requirements for each line of the material standard. Unless otherwise specifically requested by the purchaser, a particu
39、lar inspection and/or test for release shall be carried out if corresponding acceptance criteria and/or values are stated in the applicable material standard, but see also in 6.3.5. 6.3.2 Retests If any requirement is not met, retests shall be carried out under the following conditions unless otherw
40、ise stated in the material standard or order. Copyright ASD-STAN Provided by IHS under license with AECMA Not for ResaleNo reproduction or networking permitted without license from IHS-,-,-prEN 4700-002:2009 (E) 7 If the test procedure or test piece preparation is faulty, testing shall be re-applied
41、 at the original frequency after rectification of the original cause of failure, on a test sample located near the first one. For bars or sections with hardness results below the minimum or above the maximum value, the softest or hardest bars or sections, as appropriate, shall be submitted to a tens
42、ile test and, if required, an impact test. If the results comply with the specified tensile and impact requirements, all bars or sections shall be accepted. When failure cannot be attributed to faulty testing, or test piece preparation, further test samples shall be selected at twice the original fr
43、equency from the product, one of which shall be that on which the original results were obtained unless already withdrawn by the manufacturer after suitable identification of the cause of failure. If all retest results are satisfactory, the batch shall be accepted. If one or more tests are unsatisfa
44、ctory, the batch shall be: rejected, or 100 % retested and the conforming products accepted, or; partially or fully re-heat treated if heat treatment can rectify the cause of the failure and tested as a completely new batch except for chemical composition and cleanness inspection. The reheat treatme
45、nt shall be stated on the release test certificate. For cleanness inspection, if the material fails the requirement the product may be cut back before retesting. 6.3.3 Rejection Any failure to meet the requirements of the material standard shall be cause for rejection. 6.3.4 Special tests Special te
46、sts may be required by the purchaser. In such cases, the nature of the test, method, frequency and technical requirements shall be specified on the order or inspection schedule and shall be mutually agreed by the manufacturer and the purchaser. 6.3.5 Capability clause Where the capability clause is
47、invoked and where sufficient statistical evidence exists, the test need not be carried out (unless specifically requested by the purchaser). However, this in no way reduces the obligations of the manufacturer to fulfil the requirements. If subsequent testing indicates that the product does not compl
48、y with the requirements, the batch shall be rejected. If sufficient statistical evidence does not exist, the test shall be carried out at a frequency agreed between the manufacturer and purchaser. 6.3.6 Statistical process control Reduction in the extent of release testing, other than that defined in 6.3.5 above, may be negotiated with the purchaser on the basis of appropriate statistical process control and/or statistical data. Copyright ASD-STAN Provided by IHS under license with AECMA Not for ResaleNo reproduction
copyright@ 2008-2019 麦多课文库（www.mydoc123.com）网站版权所有
备案/许可证编号：苏ICP备17064731号-1