AECMA PREN 6059-100-2001 Aerospace Series Electrical Cables Installation Protection Sleeves Test Methods Part 100 General Edition P 2《航空航天系列.安装保护轴套电缆试验方法.第100部分 总则.P2版》.pdf

1、AECMA STANDARD NORME AECMA AECMA NORM Edition approved for publication Comments should be sent within six months after the date of publication to prEN 6059-1 O0 Edition P 2 July 2001 AIBfTF3 Chairman - PUBLISHED BY THE EUROPEAN ASSOCIATION OF AEROSPACE INDUSTRIES - STANDARDIZATION (AECMA-STAN) Gulle

2、delle 94 - 8-1200 BRUXELLES - Tel. (t32) 2 775 81 10 - Fax. (+32) 2 775 81 11 ICs: September 1997 Supersedes edition P 1 Descriptors: ENGLISH VERSION Aerospace series Electrical cables, installation Protection sleeves Test methods Part 100: General Srie arospatiale Cbles lectriques, installation Gai

3、nes de protection Mthodes dessais Partie 100: Gnralits Luft- und Raumfahrt Elektrische Leitungen, Installation Schutzschluche Prfverfa h ren Teil 100: Allgemeines This Yerospace Series“ Prestandard has been drawn up under the responsibility of AECMA-STAN (The European Association of Aerospace Indust

4、ries - Standardization). It is published on green paper for the needs of the European Aerospace Industry. It has been technically approved by the experts of the concerned Domain following member comments. Subsequent to the publication of this Prestandard, the technical content shall not be changed t

5、o an extent that interchangeability is affected, physically or functionally, without re-identification of the standard. After examination and review by users and formal agreement of AECMA-STAN it will be submitted as a draft European Standard to CEN (European Committee for Standardization) for forma

6、l vote. 2001-07-31 AECMA-STAN Gulledelle 94 B-1200 BRUXELLES Mr Luck I I aecma 200 Copyright Association Europeene des Constructeurs de Materiel Aerospatial Provided by IHS under license with AECMANot for ResaleNo reproduction or networking permitted without license from IHS-,-,-Page 2 prEN 6059-100

7、: 2001 Content list Page 3 Normative references . 3 Definitions Test conditions Reporting results 4 List of test methods . a Copyright Association Europeene des Constructeurs de Materiel Aerospatial Provided by IHS under license with AECMANot for ResaleNo reproduction or networking permitted without

8、 license from IHS-,-,-Page 3 prEN 6059-100: 2001 I Scope This standard specifies the general conditions for test methods applicable to protection sleeves for electrical cable and cable bundles for aerospace application. 2 Normative references This European Standard incorporates by dated or undated r

9、eference provisions from other publications. These normative references are cited at the appropriate places in the text and the publications are listed hereafter. For dated references, subsequent amendments to or revisions of any of these publications apply to this European Standard only when incorp

10、orated in it by amendment or revision. For undated references the latest edition of the publication referred to applies. EN 3844-1 EN 6049-001 EN 6059-201 EN 6059-202 EN 6059-203 EN 6059-301 EN 6059-302 EN 6059-303 EN 6059-306 EN 6059-401 EN 6059-402 EN 6059-403 EN 6059-404 EN 6059-405 0 EN6059406 A

11、erospace series - Flammability of non metallic materials - Part 1: Small burner test, vertical - Determination of the vertical flame propagation 1) Aerospace series - Electrical cables, installation - Protective sleeves in meta-aramid fibres - Part O01 : Technical specification 1) Aerospace series -

12、 Electrical cables, installation - Protection sleeves - Test methods - Part 201: Visual examination 1) Aerospace series - Electrical cables, installation - Protection sleeves - Test methods - Part 202: Dimenssions and mass 1) Aerospace series - Electrical cables, installation - Protection sleeves -

13、Test methods - Part 203: Coverage 1) Aerospace series - Electrical cables, installation - Protection sleeves - Test methods - Part 301 : Sun light exposure 1) Aerospace series - Electrical cables, installation - Protection sleeves - Test methods - Part 302: High temperature exposure 1) Aerospace ser

14、ies - Electrical cables, installation - Protection sleeves - Test methods - Part 303: Resistance to fluids 1) Aerospace series - Electrical cables, installation - Protection sleeves - Test methods - Part 304: Flammability 1) Aerospace series - Electrical cables, installation - Protection sleeves - T

15、est methods - Part 305: Fluid absorption 1) Aerospace series - Electrical cables, installation - Protection sleeves - Test methods - Part 306: Mould growth 1) Aerospace series - Electrical cables, installation - Protection sleeves - Test methods - Part 401 : Expansion range 1) Aerospace series - Ele

16、ctrical cables, installation - Protection sleeves - Test methods - Part 402: Bending properties 1) Aerospace series - Electrical cables, installation - Protection sleeves - Test methods - Part 403: Scrape abrasion 1) Aerospace series - Electrical cables, installation - Protection sleeves - Test meth

17、ods - Part 404: Tensile strength 1) Aerospace series - Electrical cables, installation - Protection sleeves - Test methods - Part 405: Dynamic cut-through 1) Aerospace series - Electrical cables, installation - Protection sleeves - Test methods - Part 406: Vibration 1) 1) Published as AECMA Prestand

18、ard at the date of publication of this standard Copyright Association Europeene des Constructeurs de Materiel Aerospatial Provided by IHS under license with AECMANot for ResaleNo reproduction or networking permitted without license from IHS-,-,-Page 4 prEN 6059-100: 2001 201 202 3 Definitions For th

19、e purpose of this standard, the definitions in EN 6049-001 apply. Visual inspection Dimensions and mass 4 Test conditions 302 303 The tests shall be carried out under the following atmospheric conditions: - Ambient temperature shall be (+ 20 i 5) OC. - Relative humidity shall be between 45 % and 75

20、%. High temperature exposure Resistance to fluids 5 Reporting results 304 or EN 3844-1 305 The following details shall be reported: - Approved drawings. - Type and size code. - Length of specimen if this not specified in the test method or if there is a deviation with respect to the test method. Fla

21、mmability Fluid absordion 6 List of test methods EN 6059- 401 402 403 See Table 1, Table 2 and Table 3. Table 1 -General tests Title Expansion range Bending properties Scraoe abrasion I EN 6059- I Title I 404 405 Tensile strength Dvnamic cut-throuah 406 Vibrations I l 30 1 Sun light exposure I Copyright Association Europeene des Constructeurs de Materiel Aerospatial Provided by IHS under license with AECMANot for ResaleNo reproduction or networking permitted without license from IHS-,-,-