AECMA PREN 9300-013-2006 Aerospace series LOTAR LOng Term Archiving and Retrieval of digital technical product documentation such as 3D CAD and PDM data Part 013 Reference process .pdf

1、ASD STANDARD NORME ASD ASD NORM prEN 9300-013 Edition P 1 October 2006 PUBLISHED BY THE AEROSPACE AND DEFENCE INDUSTRIES ASSOCIATION OF EUROPE - STANDARDIZATIONGulledelle 94 - B-1200 Brussels - Tel. + 32 2 775 8126 - Fax. + 32 2 763 3565 - www.asd-stan.orgICS: Descriptors: ENGLISH VERSION Aerospace

2、series LOTAR LOng Term Archiving and Retrieval of digital technical product documentation such as 3D, CAD and PDM data Part 013: Reference process description Archival Storage Srie arospatiale LOTAR Archivage Long Terme et rcupration des donnes techniques produits numriques, telles que CAD 3D et PDM

3、 Partie 013 : Description du processus de rfrence Stockage darchive Luft- und Raumfahrt LOTAR Langzeitarchivierung und Bereitstellung digitaler technischer Produktdokumentationen, beispielsweise 3D CAD und PDM Daten Teil 013: Referenzprozessbescheibung Speicherung This “Aerospace Series“ Prestandard

4、 has been drawn up under the responsibility of ASD-STAN (The AeroSpace and Defence Industries Association of Europe - Standardization). It is published for the needs of the European Aerospace Industry. It has been technically approved by the experts of the concerned Domain following member comments.

5、 Subsequent to the publication of this Prestandard, the technical content shall not be changed to an extent that interchangeability is affected, physically or functionally, without re-identification of the standard. After examination and review by users and formal agreement of ASD-STAN, it will be s

6、ubmitted as a draft European Standard (prEN) to CEN (European Committee for Standardization) for formal vote and transformation to full European Standard (EN). The CEN national members have then to implement the EN at national level by giving the EN the status of a national standard and by withdrawi

7、ng any national standards conflicting with the EN. Edition approved for publication 31 October 2006 Comments should be sent within six months after the date of publication to ASD-STAN Engineering Procedures and Processes Domain Copyright 2006 by ASD-STAN Copyright Association Europeene des Construct

8、eurs de Materiel Aerospatial Provided by IHS under license with AECMA Not for ResaleNo reproduction or networking permitted without license from IHS-,-,-prEN 9300-013:20062 Contents Page Foreword3 1 Scope 4 2 Normative references 4 3 Terms, definitions and abbreviations4 4 Applicability4 5 Archival

9、storage.5 6 Detailed process steps description .6 6.1 General6 6.2 AIP transfer to main storage.6 6.3 Initiate digital time signature process .6 6.4 Set digital time signature 6 6.5 Store to media7 6.6 Storage assurance.7 6.7 Update Descriptive Information .7 6.8 Update meta data base8 6.9 Confirm t

10、he archiving8 6.10 Generate confirmation report.8 6.11 Receive confirmation 8 6.12 Receive confirmation 9 6.13 Disaster Recovery .9 6.14 Error handling for archival storage9 6.15 Manual edition of Descriptive Information (by the producer) .9 6.16 Manual edition of Descriptive Information (by the adm

11、inistrator)9 7 Support process steps: 10 7.1 Preservation Planning 10 7.2 Guarantee quality of archive . 10 7.3 Administration. 10 7.4 Data Management . 10 8 Data descriptions 11 8.1 General. 11 8.2 Involved roles 11 8.3 Involved data. 11 Bibliography. 14 Figure Figure 1 Archival Storage.5 Copyright

12、 Association Europeene des Constructeurs de Materiel Aerospatial Provided by IHS under license with AECMA Not for ResaleNo reproduction or networking permitted without license from IHS-,-,-prEN 9300-013:20063 Foreword This standard was prepared jointly by ASD-STAN and the PROSTEP iViP Association. T

13、he PROSTEP iViP Association is an international non-profit association in Europe. For establishing leadership in IT-based engineering it offers a moderated platform to its nearly 200 members from leading industries, system vendors and research institutions. Its product and process data standardizati

14、on activities at European and worldwide levels are well known and accepted. The PROSTEP iViP Association sees this standard and the related parts as a milestone of product data technology. Users should note that all standards undergo revision from time to time and that any reference made herein to a

15、ny other standard implies its latest edition, unless otherwise stated. Copyright Association Europeene des Constructeurs de Materiel Aerospatial Provided by IHS under license with AECMA Not for ResaleNo reproduction or networking permitted without license from IHS-,-,-prEN 9300-013:20064 1 Scope EN

16、9300-013 provides a detailed description for the recommended process of the Archival Information Package within the archive as overviewed in EN 9300-010. A main focus lays on the secure process, which implies the setting of digital signatures, disaster recovery and update of archive meta data base.

17、2 Normative references The following referenced documents are indispensable for the application of this document. For dated references, only the edition cited applies. For undated references, the latest edition of the referenced document (including any amendments) applies. ISO 14721:2003, Space data

18、 and information transfer systems Open archival information system Reference model OAIS. EN 9300-003, Aerospace series LOTAR LOng Term Archiving and Retrieval of digital technical product documentation such as 3D, CAD and PDM data Part 003: Fundamentals and concepts. 1)EN 9300-007, Aerospace series

19、LOTAR LOng Term Archiving and Retrieval of digital technical product documentation such as 3D, CAD and PDM data Part 007: Terms and References. 1)EN 9300-010, Aerospace series LOTAR LOng Term Archiving and Retrieval of digital technical product documentation such as 3D, CAD and PDM data Part 010: Ov

20、erview Data Flow. 2)3 Terms, definitions and abbreviations For the purposes of this standard, the terms, definitions and abbreviations given in EN 9300-007 shall apply. 4 Applicability This EN 9300-013 is applicable to new 3-D product data records and may be applicable to existing 3D product data re

21、cords, on current and earlier products, produced using previous regulations, standards and procedures. The current version is focused on product data as defined in the domain specific parts. 1) In preparation at the date of publication. 2) Published as ASD Prestandard at the date of publication of t

22、his standard. Copyright Association Europeene des Constructeurs de Materiel Aerospatial Provided by IHS under license with AECMA Not for ResaleNo reproduction or networking permitted without license from IHS-,-,-prEN 9300-013:20065 5 Archival storage See Figure 1. Figure 1 Archival Storage The proce

23、ss includes the setting of digital time signatures, generation of additional Descriptive Information (DI) for AIPs (meta data for the archive), the physical storage of the data within the archive and error checking as well as the steps needed disaster recovery of the stored data. Each company should

24、 meet the general recommendations for an archive system and its security, as for example described in ISO 14721:2003 (OAIS). These general recommendations are out of scope. The sub process shall be certified. Process Steps Store to Media, Storage assurance, Update meta-database and Disaster Recovery

25、 cover administrative aspects of the archive and its software. The steps are out of scope for the process description and this standard. They are shown for completeness. If needed by the community, the preservation of the Desciptive Information of the Archive will be described in the recommended pra

26、ctises of the part 13. Input data: AIP DI Output data: Process control data Copyright Association Europeene des Constructeurs de Materiel Aerospatial Provided by IHS under license with AECMA Not for ResaleNo reproduction or networking permitted without license from IHS-,-,-prEN 9300-013:20066 6 Deta

27、iled process steps description 6.1 General Input and output data described in this standard represent the minimal requirements for the fulfilment of the process steps. Additional data may be added, but must match at a minimum the requirements for the information package. (See EN 9300-003, section 5.

28、3.2.1 “Definition of the core model”). 6.2 AIP transfer to main storage The Archive transfers the AIP from the working environment to the physical storage environment. Input data: AIP Output data: AIP 6.3 Initiate digital time signature process The administrator initiates the digital time signature

29、process. Output data: Request for authentication Request for time stamp Secret key 6.4 Set digital time signature The archive sets a digital (time) signature according to the applicable digital signature law. This assures the data integrity, readability and exchangeability during the retention perio

30、d, and may be used as evidence when identifying the provenance of the information. NOTE A digital time signature is any unique set of letters, characters, symbols or code attached to a digital document with the intention of identifying the sender. At the lower end of the e-signature security scale a

31、re formats such as email signatures and the simple attachment of signature images. Higher up the scale we find more secure formats such as pin numbers. At the upper end of the scale are formats using more complex technologies combining mathematical processes, encryption and controlled systems. Input

32、 data: Request for authentication Request for time stamp Secret key AIP Support information Output data: AIP Digital signature information Copyright Association Europeene des Constructeurs de Materiel Aerospatial Provided by IHS under license with AECMA Not for ResaleNo reproduction or networking pe

33、rmitted without license from IHS-,-,-prEN 9300-013:20067 6.5 Store to media The Archive stores the AIP physically onto a medium according to meet the requirements of long term archiving and the availability of the stored data. Input data: AIP Support information Output data: Storage information 6.6

34、Storage assurance The storage assurance function validates the successful transfer of the AIP to the staging area. For digital submissions, these mechanisms might include Cyclic Redundancy Checks (CRCs) or checksums associated with each data file, or the use of system log files to record and identif

35、y any file transfer or media read/write errors. Input data: Storage information Output data: In any case: Statistics If assurance is successful: Results If assurance fails: Error report 6.7 Update Descriptive Information The archive updates the set of descriptive information regarding the storage as

36、surance and digital time signature information. Input data: Results Digital time signature information DI Output data: If update is successful: DI If update fails: Error report Copyright Association Europeene des Constructeurs de Materiel Aerospatial Provided by IHS under license with AECMA Not for

37、ResaleNo reproduction or networking permitted without license from IHS-,-,-prEN 9300-013:20068 6.8 Update meta data base The archive generates a new entry within the archives meta data base. The new entry contains the descriptive information, in addition for example, the reference information, which

38、 defines the storage location. Input data: DI Support information Output data: If update is successful: Meta data base update report Meta data base update information (Including the Descriptive Information) If update fails: Error report 6.9 Confirm the archiving The archive confirms the archiving pr

39、ocess after the update of the meta data base. Input data: Meta data base update report Output data: Confirmation information 6.10 Generate confirmation report The archive generates a confirmation report which includes the feedback information for the consumer/ administrator according to the archivin

40、g/removal procedures. Input data: Confirmation information Output data: Archiving confirmation report 6.11 Receive confirmation (by the administrator) The administrator receives the archives confirmation report. Input data: Confirmation report (for archiving) Output data: Copyright Association Europ

41、eene des Constructeurs de Materiel Aerospatial Provided by IHS under license with AECMA Not for ResaleNo reproduction or networking permitted without license from IHS-,-,-prEN 9300-013:20069 6.12 Receive confirmation (by the producer) The producer receives the archives confirmation report. Input dat

42、a: Confirmation report (for archiving) Output data: 6.13 Disaster Recovery The archive duplicates the AIPs and stores the duplicate in a physically separate facility. Input data: If disaster recovery is successful: AIP Meta data base update information Output data: If disaster recovery fails Error r

43、eport 6.14 Error handling for archival storage Within this process the Administrator has to perform error fixing procedures for the storage of archiving information packages, the update of meta data base and the preparation for disaster recovery. Input data: Error report Output data: Process control

44、 data 6.15 Manual edition of Descriptive Information (by the producer) The Producer shall have the ability to edit and attach several descriptions to the AIPs. The additional Descriptive Information could be, for example, the end of production date for a product - this is not known at the date the d

45、ata is stored. Input data: DI Output data: DI (completed by the producer) 6.16 Manual edition of Descriptive Information (by the administrator) The Administrator shall have the possibility to edit and attach several Descriptive Information to the AIPs. The additional Descriptive Information could be

46、, e.g., the end of production date for a product, which is not known at the date of the archival storage. Copyright Association Europeene des Constructeurs de Materiel Aerospatial Provided by IHS under license with AECMA Not for ResaleNo reproduction or networking permitted without license from IHS-

47、,-,-prEN 9300-013:200610 Output data: DI (revised by the administrator) 7 Support process steps: 7.1 Preservation Planning The process provides services and functions for monitoring the environment of the archive and recommendations to ensure that the information stored in the archive remains access

48、ible to the consumer over the long term, even if the original computing environment becomes obsolete. Preservation Planning functions include developing recommendations for archive standards and policies and monitoring changes in the technology environment, archiving format and the addressed consumer. Output data: Support information 7.2 Guarantee quality of archive The process describes the common administrative procedures, which are necessary for maintaining the arch