AIR FORCE A-A-50757-1986 FOUR CHANNEL RECORDER《四导程记录器》.pdf

1、COMMERCIAL ITEM DESCRIPTION A-A-507 5 7 1 October 1986 I FOUR CHANNEL RECORDER The General Services Administration has authorized the use of this Commercial Item Description. SCOPE. This Comercial Item Description (CID) specifies a portable four 50MM channel recorder which features a four-channel DC

2、 and amplifier range 02 50MV to-5-OOV 500VDC. mnitors- three cylinder hydraulic fluid flows. the changes between the three- test signals. This system shall be known as a four channel recorder. full scale with a capability of a maximum common mode voltage of The recorder picks up test signals from a

3、function generator that The fourth channel monitors APPLICABLE DOCUMENTS. MIL-M- 7 2 9 8 Manual Technical Commercial Equipment. XIL-T-28800 Test Equipment for use with Electrical and Electronics MIL-M-38797 Manual Technical, Operation Instructions and Maintenance Equipment General Specification for.

4、 Instructions (for Various Types of Equipment). SALIENT CHARACTERISTICS. 1. Performance requirements of the four channel Oscillographic Recorder. a. Four channel recorder. The four channel recorder monitors four in- put test signals (5 volt full scale) with a 115VAC line voltage at a frequency range

5、 of 50 to 400HZ. b. Precision. The servo control penmoter should enforce 99.65% linear- ity over the entire channel, regardless of the channel width. Chart speed accuracy is + 0.25% from 15 to 35 degrees Celsius temperature range and is independent of line frequency from 50 to 400HZ. c. Chart speed

6、control. Must permit fixed or continuous variableopera- tion of chart speed from 100% to 40% of selected speeds. The vari- able control is for reducing paper consumption or improving record- ing readability. Selection of the six calibrated speeds are by front-panel pushbuttons, or remote via TTL, or

7、 contact closure. The speed selections are 5, 10, 25, 50, 100, or 200 mm/sec and a divide-by-100 speed to reduce chart speed to 1/100th of the value selected by puchbutton. The external speed selection is achieved by applying an external pulse with a frequency ranging from O to 20 KHZ which correspo

8、nds with the resulting chart speed of O to 250 mm per second. Using this frequency range, the incremental chart drive response to the pulse at 30 microsecons with 10 microsecons minimum duration. . THIS DOCUMENT CONTAINS y PAGES. FSC 6625 Approved for public release; distribution is unlimited. DISTR

9、IBUTION STATEMENT A. Licensed by Information Handling ServicesA-A-50757 hh m 7777774 OCIL0405 4 W A-A-50757 d. Trace. The pen must record in true rectilinear, precise, instant drying, and of constant width of 0.01 inches nominal at any chart speed velocity. It must have sufficient ink supply for at

10、least one year of typical use and have a chart length of 275 feet nominal. The pen must record in any position, be clog free, and start writing immediately even after remaining idle for long periods. can be either pressurized fluid or fine-line thermal marking. fine-line thermal marking the recorder

11、 should be resistant to pressure, will not wear out over the life of the recorder, and will not prematurely burn out even in the most demanding applications. The tracer For e. Event markers, The left and right event marker pens will have cod- ing information and recording events capability. markers

12、should also mark time which is activated by a timer that generates a 40-MS output pulse at eight internally programmable repetition rates of 0.1, 1, 10, 1000 seconds, and 0.01, 0.1, 1 and 10 minutes. One of the event f. Operating temperature. The opgrating temperature for the four channel recorder i

13、s OC at +SO C. g, Storage temperature. The storage temperature for the four channel recorder is -40C to +7OoC. h. Humidity. ing . The humidity for the recorder is 95% at 32OC noncondens- 2. Performance requirements of each recorder. a, Frequency response. The frequency response at 50-MM amplitude is

14、 DC to 50 HZ + 2%. For alternate amplitudes, such as 100-MM amplitude, it is DC to 30 HZ + 2%, and for 40-MM amplitude it is DC to 60 HZ + 2%. b. Rise time. The rise time at 10% to 90% full scale with less than 1% overshoot is 5 milliseconds at 50-MM amplitude. Alternate rise time are 8 milliseconds

15、 at 100-MM amplitude, and 4 milliseconds at 40-MM amplitude. c. Pen position. The analog pen can be positioned anywhere on the channel and still have a continuously adjustable + 100% full scale. d. Common mode rejection noise ratio. inbalance across the input signal points is 80 DB for DC signals an

16、d 60 DB for 60 HZ signals. The rejection ratio at 1 KOHM 3. Stability. a, Zero-line instability (drift), The zero-line instability of the recorder after 15 minutes of warmup is + 0.1% of full scale for 24 hours or running, + 0.05% of full scale per degree celsius, and +0.05% of reading for+ 10% line

17、 voltage change, - - 2 Licensed by Information Handling Services- A-A-50757 66 7977974 OOL0406 b A-A- 50757 b. Gain instability. The gain instability of the recorder is +0.1% of reading for 24 hours of running, +0.05% of reading per degree Celsius, and - +O.O5%-of reading for - +lo% line voltage cha

18、nge. 4. Specify type and size. a. b. C. d. e. f. g. Design and construction. Unless otherwise specified herein, the equipment shall comply with the Type III design and construction requirements specified in .MIL-T-28800. Solid state construction. The equipment shall be of solid-state mod- ular minia

19、turized construction. Electron tubes shall not be used. Receptacle and connector mounting. provided on barrier strip for jumper wire assembly. The connectors shall comply with MIL-T-28800 3.4.1.5.2. All AC/DC input connectors are Signal adjustment. All output signals shall be externally adjust- able

20、 100 to 40%. Accessibility. The equipment shall be constructed so subassemblies and chassis components can be removed without removing any other hardware subassemblies, printed circuit card or component. Input power switch. The input power switch shall comply with Type III input switch requirements

21、of MIL-T-28800, except that the switch shall break both sides of the po-.ler source, but not break the earth ground conductor circuit. Fuses or circuit breakers. Fuses or circuit breakers shall comply with Type III requirements of MIL-T-28800. Input power line shall be equipped with fuses or circuit

22、 breakers. 5. Dimensions, weight and mechanical stability. a. Weight. The unpacked weight of the power supply, including all accessories, shall be 105 pounds nominal. b. Dimensions. The dimensions of the Eour-channel recorderaccessories, installed in the Style F enclosure as referenced in MIL-T-2800

23、 shall be 19.31 inches in width, 17.22 inches in height and 14.75 inches in depth. CERTIFICATION. The contractor shall certify that the product offered meets the salient characteristics of this description, and that the product conforms to the producers own drawings, specifications, standards and qu

24、ality assur- ance practices. the salient characteristics of this Commercial Item Description at San Antonio ALC, Kelly AFB, TX 78241. Bid samples from bidders will be tested in accordance with OPERATIONAL INSTRUCTIONS/MAINTENANCE MANUAL. The contractor shall prepare an operators manual according to

25、the provisions of MIL-M-38797 for all equip- ment delivered under terms of this -contract. 3 Licensed by Information Handling ServicesA-A-50757 bb W 777977Li OOLOLi07 A A-A- 50757 COMMERCIAL PUBLICATIONS. Commercial publications may be submitted to fulfill Air Force documentation requirements. order

26、 numbering and must be referenced in the system level publication. Such commercial data must be prepared in accordance with MIL-M-7298. of each commercial manual proposed shall be submitted for Air Force evaluation and approval. Order Management Office (TOMO) before final acceptance by the Air Force

27、. modifications are performed on Air Force equipment, the contractor shall pro- vide updating manual changes to meet Air Force standards, reproduction rights for government use must accompany submittals. These publications require technical Two copies Commercial publications shall be reviewed by the

28、 Technical If All applicable INTENDED USE. The equipment shall be designed for use at Air Force Base and Depot Precision Measuring Equipment Laboratories. REGULATORY REQUIREMENTS. The offeror/contractor is encouraged to use recovered materials in accordance with Public Law 94-580 to the maximum exte

29、nt practical. PACKAGING, PACKING AND MARKING. The items shall be packaged in accordance with normal commercial practice and packed to assure acceptance by common carrier and provide product protection against loss and damage during multiple shipments, handling, and storage. The shipping container sh

30、all be in compli- ance with national motor freight classification and uniform freight classifi- cation. Shipping containers shall be marked as specified in the contract or order. KNOWN ACCEPTABLE PRODUCTS. Manu f ae t Ure r Model Gould Electronics and Electrical P/N 2107-8809-00 Products For competitive bidding Custodian: Navy - EC Air Force - 99 Review activity: Army - CR DLA - ES NSN 6625-01-124-4185 - Preparing activity: Air Force - 82 (Project 6625-0657) U.8. 8OVERNHEt4T PRINTXNQ OFFICE: 1966 - 704-036/45503 4 Licensed by Information Handling Services