AIR FORCE A-A-58032-1994 TEST SET ELECTRICAL POWER《电力测试装置》.pdf

1、_ A-A-58032 H 9999974 OLb5470 97T INCH POUND October 17, 1994 A-A-58032 COMMERCIAL ITEM DESCRIPTION TEST SET, ELECTRICAL POWER The General Services Administration has authorized the use of this Commercial Item Description ( CID ) for all federal agencies. 1. sco PE. This CID, describes a Test Set, E

2、lectrical Power. This CID is meant as a minimum requirement for the Test Set, Electrical Power in which only those manufacturers that meet or surpass the following requirements are qualified per this CID. The Test Set is to be used for making level, frequency, noise, and noise-to-ground measurements

3、 on telephone lines. 2. CLASSIFICATION, Equipment covered by this CID may be commercially available equipment modified to the extent necessary to meet the following description. The equipment shall be Type III, Class 5, Style E and Color R in accordance with MIL-T-28800. 3. SALIENT CHARACTERISTICS,

4、3.1 Desim and Co nstruction, The equipment shall be UL (Underwriters Laboratories) listed and approved and/or shall comply with the type III safety requirements of MIL-T-28 800. 3.2 Electrical Power Sources. The equipment shall operate from nominal commercial, military and shipboard power sources of

5、 115/230 volts AC (+-lo%) at line frequencies of 50 Hz to 60 Hz. Transient state conditions shall meet MIL-T-28800 Class 5 requirements. The unit shall also operate from an internal, rechargeable battery pack for a minimum of three (3) hours. Beneficial comments, recommendations, additions, deletion

6、s, clarifications etc., and any data which may improve this document should be sent to: The Resources and Logistics Services Division, SA-ALC/TILDD, Bldg. 171, Post C-12,485 Quentin Roosevelt Rd., Kelly AFB TX 78241 -6524. AMSC N/A FSC 6625 DISTRIBUTION S TATEM ENT A. Approved for public release; di

7、stribution is unlimited. Licensed by Information Handling ServicesProvided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,- A-A-56032 W 9999974 OLb5q7L 806 W A-A-58032 3.3 (a) ODeratine Temperature. The equipment shall meet its performance and accuracy requir

8、ements in an operating environment of 0C to +5OoC. (b) -. The equipment shall meet its performance and accuracy requirements in a non-operating environment of -40C to +60C. 3.4 1). The equipment MTBF shall be 2,000 hours. The lower test MTBF shall be 2,000 hoursand the upper test MTBF shall be 4,000

9、 hours. 3.5 Pre-conditionin- Requirement. Each deliverable equipment shall be capable of being subjected to the environmental screening effects of bum in and thermal cycling, with thermal cycling being accomplished in the sample testing phase. 3.6 Calibration and Maintenance Adjustments. The design

10、of the system shall provide for readily accessible calibration adjustments and maintenance adjustments. These adjustments shall be provided by variable value components which are adjustable by the use of simple means. The calibration by substitution of selected components or parts is unacceptable un

11、less specifically approved. The calibration. adjustments, wherever possible, shall be accessible without removal of the instrument case or modules. The calibration interval shall be a period of one year or greater based on an operating time of 2,000 hours. 3.7 Performance Characte ristics. The Test

12、Set shall be capable of performing the following measurements in accordance with IEEE 743- 1984 and shall meet or exceed the measurement parameters listed below: (a) Level Measurements. (a Range (b) Resolution (c) Accuracy (b) Frequencv Measurements. (a) Range (b) Resolution (c) Accuracy 40.0 dBm to

13、 +13 dBm - +OS dBm up to 20 kHz 0.1 dBm 50 Hz to 20 kHz 1 Hz from 50 to 4 kHz 10 Hz from 4K to 20 kHz - +1 Hz from 50 to 4 kHz O Hz from 4 K to 20 kHz 2 Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-A-A-58032 9999974 Olla5472 742 W A-A-58032 (c) No

14、ises. (a Range 10 dBm to 99 dBm (b) Resolution 1 dBm (c) Accuracy +2.0 dBm from O to 20 dBm Il .O dBm from 20 to 99 dBm (d) Noise-to-Ground Measurements. (a) Range (b) Resolution (c) Accuracy 50 dBm to 130 dBm 1 dBm - +1.5 dBm 3.8 Connectors. The equipment shall provide the following front panel con

15、nectors: WECO type 309 or 3 1 O; additionally, binding posts are preferred but not required. In accordance with section 23.403 of the Federal Acquisition Regulations, the Governments policy is to acquire items composed of the highest percentage of recovered materials practicable, consistent with mai

16、ntaining a satisfactory level of competition without adversely affecting performance requirements or exposing the suppliers employees to undue hazards from the recovered materials. 5. PACKAGING. The items shall be packed in accordance with normal commercial practice and packed to assure acceptance b

17、y common carrier and provide product protection against loss and damage during multiple shipments, handling, and storage. The shipping shall be in compliance with national motor freight classification and uniform freight classification. Shipping container shall be marked as specified in the contract

18、 or order. Certification. The contractor shall certify and maintain substantiating evidence that the product offered meets the salient characteristics of this CID, and that the product conforms to the producers own drawings, specifications, standards and quality assurance practices. The Government r

19、eserves the right to require proof of such conformance prior to first delivery, and thereafter, as may be otherwise provided for under the provisions of the contract. The Contracting Officer has the option of accepting or rejecting the product. 3 Provided by IHSNot for ResaleNo reproduction or netwo

20、rking permitted without license from IHS-,-,-7. NOTES, Metric Products. Products manufactured to metric dimensions will be considered on an equal basis with those manufactured using inch-pound units, provided they fall within the specified tolerances using conversion tables contained in the latest r

21、evision of Federal Standard No. 376, and all other requirements of this CID are met. If a product is manufactured to metric dimensions exceeding the tolerances specified in the inch-pound units, a request should be made to the contracting officer to determine if the product is acceptable. Federal an

22、d Military specifications are available from the Defense Documents Order Desk, Building 4D, 700 Robins Avenue, Philadelphia, PA 191 11-5094. Known Acceptable Products . The following product(s) are known to have previously met the salient characteristics of this CID and need not resubmit bid samples

23、 or certification. All other manufacturers must meet the requirements of this CID and submit to bid testing and certification as required: Manufacturer Hekimian Ameritec Hewlett-Packard CXR Telecom MILITARY INTERESTS: Air Force - 99 Model NSN 42-1 0-24 6625-01 -067-8835 AM42 6625-01 -276-6503 4935AEOl 6625-01 -205-6492 70 1 A-O2 6625-0 1-269-7949 PREPARING ACTIVITY: Air Force - 82 Project Nos. 6625-073 1 6625-0804 4 Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-