ImageVerifierCode 换一换
格式:PDF , 页数:5 ,大小:48.61KB ,
资源ID:426960      下载积分:2000 积分
快捷下载
登录下载
邮箱/手机:
温馨提示:
如需开发票,请勿充值!快捷下载时,用户名和密码都是您填写的邮箱或者手机号,方便查询和重复下载(系统自动生成)。
如填写123,账号就是123,密码也是123。
特别说明:
请自助下载,系统不会自动发送文件的哦; 如果您已付费,想二次下载,请登录后访问:我的下载记录
支付方式: 支付宝扫码支付 微信扫码支付   
注意:如需开发票,请勿充值!
验证码:   换一换

加入VIP,免费下载
 

温馨提示:由于个人手机设置不同,如果发现不能下载,请复制以下地址【http://www.mydoc123.com/d-426960.html】到电脑端继续下载(重复下载不扣费)。

已注册用户请登录:
账号:
密码:
验证码:   换一换
  忘记密码?
三方登录: 微信登录  

下载须知

1: 本站所有资源如无特殊说明,都需要本地电脑安装OFFICE2007和PDF阅读器。
2: 试题试卷类文档,如果标题没有明确说明有答案则都视为没有答案,请知晓。
3: 文件的所有权益归上传用户所有。
4. 未经权益所有人同意不得将文件中的内容挪作商业或盈利用途。
5. 本站仅提供交流平台,并不能对任何下载内容负责。
6. 下载文件中如有侵权或不适当内容,请与我们联系,我们立即纠正。
7. 本站不保证下载资源的准确性、安全性和完整性, 同时也不承担用户因使用这些下载资源对自己和他人造成任何形式的伤害或损失。

版权提示 | 免责声明

本文(AIR FORCE A-A-58049 B-2008 MAGNETIC PARTICLE INSPECTION UNITS 52 INCH& 100 INCH《磁粉检验单元 52英寸&100英寸》.pdf)为本站会员(proposalcash356)主动上传,麦多课文库仅提供信息存储空间,仅对用户上传内容的表现方式做保护处理,对上载内容本身不做任何修改或编辑。 若此文所含内容侵犯了您的版权或隐私,请立即通知麦多课文库(发送邮件至master@mydoc123.com或直接QQ联系客服),我们立即给予删除!

AIR FORCE A-A-58049 B-2008 MAGNETIC PARTICLE INSPECTION UNITS 52 INCH& 100 INCH《磁粉检验单元 52英寸&100英寸》.pdf

1、 A-A-58049B INCH POUND04 Apr 2008 SUPERSEDING A-A-58049A 14 Jan 1998 COMMERCIAL ITEM DESCRIPTION MAGNETIC PARTICLE INSPECTION UNITS, 52 INCH & 100 INCH The General Services Administration has authorized the use of this Commercial Item Description (CID) for all federal agencies. 1. SCOPE. This Commer

2、cial Item Description (CID) covers 52 inch and 100 inch wet horizontal magnetic particle inspection unit which will be capable of performing conventional magnetization of ferromagnetic parts. 2. CLASSIFICATION. The magnetic particle inspection units shall be of the following sizes: Size I: 52 inch S

3、ize II: 100 inch 3. SALIENT CHARACTERISTICS. 3.1 General. It shall provide alternating current (AC) and full wave rectified direct current (DC) from a three-phase AC power supply. 3.1.1 The input power 200-240 VAC with 230 VAC nominal or 400-480 VAC with 460 VAC nominal, 50-60 Hertz, 3 phase. The un

4、it shall have a press-to-test system indicating that the proper electricity connections have been made. 3.1.2 The rated maximum output shall be at least DC 6000 amperes with not more than 6% ripple, and for AC is 5000 amperes. 3.1.3 The unit shall be self-contained requiring only connections for ele

5、ctrical and compressed air supply for operation. Beneficial comments, recommendations, additions, deletions, clarifications, etc., and any data which may improve this document should be sent to: WR-ALC/GBZO-ENV, 380 Richard Ray Blvd Ste 104, Robins AFB GA 31098-1640AMSC/NA FSC 6635 Provided by IHSNo

6、t for ResaleNo reproduction or networking permitted without license from IHS-,-,-A-A-58049B 3.2 The unit shall be capable of performing magnetic particle inspection processes as described ASTM E1444. 3.3 The unit shall be capable of magnetizing a work piece in the longitudinal and circular direction

7、s. 3.4 The maximum contact head: Size I 52 + 2 inches Size II 100 + 2 inches 3.5 The overall length of the unit shall be as follows: Size I no greater than 73 inches Size II no greater than 124 inches 3.6. Instruments for inspection shall be conveniently located to permit the operator manipulation a

8、nd viewing from the inspection station. 3.6.1 Digital ammeter shall display AC root mean square (RMS) amperes or DC amperes at the coil or contact. The meter shall incorporate a sample and hold the display that will be reset after magnetizing or demagnetizing current push button is depressed. 3.6.2

9、The current control shall be continuously variable. 3.6.3 The magnetization activation switch shall be of a type that can be activated by a knee push bar. 3.6.4 The magnetization time shall be variable from 0.20 to 2.0 seconds. 3.6.5 The headstock pressurization shall be foot switch activated 3.6.6

10、The coil shall be rail mounted, have an inside diameter of 16 inches, and be capable of producing 15,000 Ampere-turns AC and DC. 3.7 The unit shall be capable of demagnetizing any work piece previously magnetized by the same unit to less than three gausses in any directions. Both reversing DC and AC

11、 ramp demagnetization capabilities shall be built into the unit. 3.8 The operating air pressure range shall be at least 60 to 110 PSI. 2 Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-A-A-58049B 3.9 The equipment shall be capable of operating at the

12、 following duty cycles indefinitely without damage to any components 3.10 Electrical systems components, devices, wiring and insulation shall be suitable for voltages, current and duty characteristics of the circuits in which they are used shall meet the applicable requirements of the National Elect

13、rical Manufactures Association (NEMA) standards. 3.11 Accessories. The following accessories shall be included: 3.11.1 A copper rod one inch in diameter by eighteen inches in length that will provide a low resistance path for determining magnetizing current through the contact heads. 3.11.2 Four aux

14、iliary cables consisting of two No. 4/0 extra flexible insulated conductors with each cable being 15 feet in length, and two No. 2/0 extra flexible insulated cable conductors with each being 10 feet in length. Each conductor shall have a 4/0 connector on each end and shall have a suitable heavy duty

15、, oil-resisting insulation. 3.11.3 A 100 Watt black light for reviewing fluorescent magnetic particle indications shall be provided. 3.11.3.1 The black light shall have an intensity of at least 1000 microwatts per square centimeter at 15 inches, and shall have a peak transmission wavelength of 365 n

16、anometers + 1.0%. 3.11.3.2 The lamp shall be mounted on swivel bracket which shall permit the lights to be directed at the parts under inspection. 3.11.4 A hood suitable for fluorescent inspections including flame retardant curtains, a white light source and ventilation fan shall be provided. 3.11.4

17、.1 The hood shall allow not more than 2 foot-candles (20 lux) of ambient light into the inspection area. 3.11.5 A set of replaceable copper braid pads for the headstock and tailstock contact plates. 3.11.6 The unit shall have a tank suitable for holding the suspension and particles, it shall include

18、 a hose long enough to reach the entire inspection area, and a nonmagnetic low pressure spray nozzle. 3.11.7 The units shall have an agitation system capable of maintaining magnetic particles in suspension. 3 Provided by IHSNot for ResaleNo reproduction or networking permitted without license from I

19、HS-,-,-A-A-58049B 3.11.8 The unit shall be delivered with all equipment necessary for immediate operation (e.g. circuit breaker box, air pressure regulator, air filter). 4. REGULATORY REQUIREMENTS. The offeror/contractor in encouraged to use recovered materials to the maximum extent practicable, in

20、accordance with paragraph 23.403 of the Federal acquisition regulation (FAR). 5. PRODUCT CONFORMANCE 5.1 Product conformance. The products provided shall meet the salient characteristics of this Commercial Item Description, conform to the producers own drawings, specifications, standards and quality

21、 assurance practices, and be the same product offered for sale in the commercial market. The government reserves the right to require proof of such conformance. 6. PACKAGING. Preservation, packing and marking shall be specified in the contract or order. 7. NOTES. 7.1 Part Identification Number (PIN)

22、. The following part identification numbering procedure is for government purposes and does not constitute a requirement for the contractor. Example of reference part number: A-A-58049-I or A-A-58049-II AA58049 - 1 Size: I 52 Inch II 100 Inch CID Document Number 7.2 Metric products. Products manufac

23、tured to metric dimensions will be considered on an equal basis with those manufactured using inch-pound units, provided they fall within the tolerances specified in conversion tables contained in the latest version of FED-STD-376 and all other requirements of this CID are met. If the manufacturer e

24、lects to use metric dimensions as the basis upon which to derive or base a mechanical feature, a request shall be made to the contracting officer to determine if the product is acceptable. The contracting officer has the option of accepting or rejecting the product. 7.3 Source of Documents. 7.3.1 AS

25、TM documents may be obtained at ASTM International - Standards Worldwideor from American Society for Testing and Materials, 100 Barr Harbor Drive, West Conshohocken, PA 19428-2959. 4 Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-A-A-58049B 7.3.2 NE

26、MA documents may be obtained at NEMA - National Electrical Manufacturers Association or from National Electrical Manufacturers Association, 1300 North 17th Street Suite 1752, Rosslyn, Virginia 22209 7.4 Ordering data. a) Title, number, and date of this CID. b) Specify special packaging requirements.

27、 c) Contracting officer may request proof of certification of commercial item prior to first contract delivery. 7.5 Subject term (key word) listing. 1. Ferromagnetic 2. Inspection Unit 3. Magnetic 4. Particle Custodians: Preparing Activity: Air Force - 99 Air Force - 84 Navy -AS DLA - GS Agent: Air

28、Force 99 (Project 6635-2008-005) NOTE: The activities listed above were interested in this document as of the date of this document. Since organizations and responsibilities can change, you should verify the currency of the information above using the ASSIST Online database at http:/assist.daps.dla.mil 5 Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-

copyright@ 2008-2019 麦多课文库(www.mydoc123.com)网站版权所有
备案/许可证编号:苏ICP备17064731号-1