AIR FORCE A-A-58061-1996 SOLDERING - DESOLDERING STATION《电动吸锡焊接枪》.pdf

1、 A-A-58061 9999974 017L829 434 = INCH-POUND A-A-58061 July 29,1996 COMMERCIAL ITEM DESCRIPTION SOLDERING - DESOLDERING STATION The General Services Administration has authorized the useof this commercial item description, for ail federal agencies. 1. SCOPE. 1.1 Generd. This Commercial Item Descripti

2、on (CID), describes a repair station for circuit boards. The equipment shall be of one type and style, used to repair a wide variety of electronic boards and components and is suited for depot or on-site repair operations. This CID is meant as a minimum requirement for the repair station in which on

3、ly those manufacturers that meet or surpass the following requirements are qualified per this CID. 2. SALIENT CHARACTERISTICS. 2.1 Design. The soldering-desoldering station shall be a compact, bench mounted, capable of all types of component installationhemoval, circuit board preparation and repair

4、into one self- contained workstation. The station shall be new (not a prototype) and one of the manufacturers current models capable of the requirements herein. The station shall include all components, parts, and features necessary to meet the performance requirements specified herein. All parts su

5、bject to wear, breakage, or distortion shall be accessible for adjustment, replacement and repair. 2.2 Console and power supply. Unless otherwise specified (see 6.2), each soldering-desoldering station shall have a console and power supply with zero power switching for desoldering static/voltage sen

6、sitive mos-type devices. The console and power supply shall be housed in a container no larger than 14 inches long x 7 inches high x 1 O inches wide, and shall not exceed 30 Beneficial comments, recommendations, additions, deletions, clarifications, etc. and any data which may improve this document

7、should be sent to: Logistics Services Division, SA- ALCTILDD, Bldg 207, Kelly AFB TX 7824 1, buy using the self addressed Standardization Document Improvement Proposal (DD Form 1426) appearing at the end of this document or by letter. AMSC N/A FSC 3439 DISTRIBUTIO N STATEMENT A. Approved for public

8、release; distribution is unlimited. Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-A-A-58061 m 9999974 0171830 L5b m A-A-58061 pounds in weight. The power source shall contain multiple channels on the front panel and shall be capable of supplying an

9、d controlling multiple sensor-driven hand pieces up to 75 watts with no more than 24 VAC to each handpiece channel. The power unit has a total power consumption of 25 watts. The console shall have a temperature display that indicates temperatures in Fahrenheit and Centigrade scale with a resolution

10、of 1 degree. The power source shall be capable of setting back temperatures of inactive hand pieces automatically or on user demand to 350 degrees F (1 80 degrees C). Temperature outputs shall be shut down after 90 minutes minimum of inactivity. A multiple LED Digital Display temperature control ran

11、ge from 100 degrees F (38 degrees C) to 900 degrees F (482 degrees C) shall be capable of recalibrating its temperature measurement circuitry for all channels while in operation and shall monitor both of status and error codes. The power source shall provide a quick rise vacuum for the desoldering h

12、andpiece and shall be capable of bringing vacuum to 10 inches of Hg in 150 mS or less when measured at the end of the extractor tip. Vacuum level shall be fixed. Supply user adjustable air flow for the hot air handpiece. Use quick connect Ciction fittings for all handpieces using air flow or vacuum.

13、 The power source shall be provided with power cords and wrist strap foot pedals as standard equipment to activate accessories. 2.3 Beso Id-p iecg. One each, desoldering handpiece with visifilter filtration shall be provided. The potential between ground and the tip of the extractor shall be less th

14、an or equal to 2mV AC RMS and the resistance, shall be equal to 2mV AC RMS and the resistance, tip of the desoldering handpiece to ground, shall be less than or equal to 2.0 ohms as measured from the tip of hot soldering irons and from the carrier of any soldering or cleaning equipment. 2.4 Conducti

15、ve tweezer. One each, conductive tweezer to provide localized heating for surface mount removal and heating for multi layer boards. 2.5 Thermal wire stripper. One each, thermal wire stripper for removal of insulation from conductors. 2.6 Resistance tweezer. One each, resistance tweezer for localized

16、 soldering or desoldering. 2.7 Thermal partindiap reflow solderinp unit. One each, thermal partingAap reflow soldering unit for installation of surface mounted devices and thermal removal of conformal coating. 2.8 Machiem t . One each, miniature machining system for milling, drilling, grinding, and

17、abrasive cleaning of components. The variable speed shall be developed over a range of 2500 to 10,000 RPM and the speed shall be capable of being maintained within 10% over a load range of 2 in-oz. The stall torque shall be a minimum of 2.5 in-oz. The handpiece shall be grounded dynamically and main

18、tain a resistance to ground not greater than 2 ohms when the unit is in operation. Braking of the hand piece shall permit drilling and machining of circuit card assemblies and shall be capable of stopping within 75 mS. The handpiece shall accommodate either a 0.09 inch collet system or a 5/32 inch c

19、huck and be provided with an assortment of 3/32 inch shank diameter ball mills, drill bits, mandrels, bristle brushes, abrasive wheels and bullet e 2 Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-A-A-58061 abrasives. Stands for the mills, drill bit

20、s, mandrels, brushes and bits shall. be provided for easy access. 2.9 Holder. One each, cubby holder shall be provided with the cleaning unit assembly for soldering and desoldering irons. 2.1 O m. One each, circuit kit repair and replacement system for use on pads, traces, and other conductors on pr

21、inted circuit assemblies unless otherwise specified (see 6.2). 2.1 1 Solderin? iron. One each, desoldering iron with pencil grip and a short tip to grip distance. A 3/16 inch shank quick change soldering tip shall be supplied with the soldering iron. 2.12 Electric power cord. A three conductor power

22、 cord not less than 7 feet or maximum of 8 feet in length shall be provided. The power cord may be permanently attached to the station or may be connected by a receptacle and plug. O 2.13 Electrical system. The electrical system shall conform to the requirements of NFPA 79. The station shall be desi

23、gned to operate from a 97-127 volts AC, 50/60 Hz, single phrase power source. 2.14 Nameplate. A nameplate shall be securely attached to each machine. Unless otherwise specified (see 6.2), the nameplate shall contain the information listed below. a. b. d. e. f. g. h. C. Nomenclature Manufacturer?s na

24、me Machine model designator Power input (volts, total amps, phase, frequency, hertz) Short circuillover current rating Contract number National stock number (NSN) Date of manufacture 3. REGULATORY REQUIREMENTS. 3.1 The offeror/contractor is encouraged to use recovered materials to the maximum extent

25、 practical, in accordanc%with paragraph 23.403 of the Federal Acquisition Regulation (FAR 4. QUALITY ASSURANCE PROVISIONS. 4.1 Product Conformance. The soldering- desoldering station provided shall meet the salient characteristics of this commercial item description, conform to the producer?s own dr

26、awings, specifications, standards, and quality assurance practices, and be the same product offered for 3 Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-A-A-5 806 1 sale in the commercial market. The government reserves the right to require proof of

27、 such conformance. 4.2 Descriptive literature. The offeror shall submit descriptive literature to evaluate the offerors product. Descriptive literature shall consist of the following: a. Proof of market acceptability (MA). The item offered must have been sold to the Government or commercial market.

28、b. Literature th% describes the work station and certificates of performance (brochures and specification sheets) showing that the unit meets the requirements of the CID. c. Complete set of drawings that includes drawings for the components. d. Copies of purchase orders, shipping documents concernin

29、g the same/similar item that has been sold to the Department of Defense. e. Commercial quality program. f. Copy of warranty which will be provided. 4.3 Bid samples. If the literature submitted is determined to be inadequate for approval, a bid sample shall be submitted to the Government for testing.

30、 A 14 to 30 day evaluation will be conducted at SA-ALCRIELQ, 508 Shop Lane, Kelly AFB, San Antonio, Texas 7824106432. The contractor shall furnish continuous maintenance support (parts and labor) during the evaluation. Bid sample shall consist of examination and testing of the unit in detail to conr

31、m adherence with the specified requirements of the CID. 5. PACKAGING. 5.1 Preservation. packaging. packing. labelin? and & . The preservation, packaging, packing, labeling, and marking shall be as specified in the contract or order. 6. NOTES. 6.1 Addresses for obtainin? copies of referenced d ocwnen

32、b. 6.1.1 Industry/commercial documents. NFPA 79-87 Electrical Standard for Industrial Machinery (Application for copies should be addressed to the National Fire Protection Association, Batterymarch Park, Quincy, MA 02269-91 O 1 .) 4 Provided by IHSNot for ResaleNo reproduction or networking permitte

33、d without license from IHS-,-,-A-A-5 806 1 6.2 Orderinp data. a. Title, number and date of this commercial item description. b. Standard equipment, if different (see 2.2) c. SpeciQ and fully describe optional equipment, if required (see 2.10 d. Electrical requirements if different, (see 2.13). e. Na

34、meplate, if different (see 2.14). f. Packaging, if different (see 5.1). 6.3 National Stock Numbers (NS Ns). The following list of NSNs assigned correspond to this CID. The list may not be indicative of all possible NSNs associated with the CID. 3439-01 -269-5494 3439-01-362-7399 343 9-0 1 -4 1 3 -89

35、55 6.4 Subject term !keyword) listing. Soldering and Desoldering Work Station Handpiece Tweezer Iron Console MILITARY INTERESTS: Custodian: Air Force - 99 Review Activity: Air Force - 84 CIVIL AGENCY COORDINATING ACTIVITIES: GSA-FSS Preparing Activity: Air Force - 82 (Project 3439-F786) 5 Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-