AIR FORCE A-A-58080 B-2009 TRUCK LIFT FORK DIESEL ENGINE-DRIVEN PNEUMATIC-TIRES 4 000 POUND CAPACITY AT 24 INCH LOAD CENTER《在24英寸的负荷中心处的额定载重为4000磅的柴油机驱动的轮胎式气动叉车》.pdf

1、 FSC 3930 INCH-POUND A-A-58080B 29 December 2009 SUPERSEDING A-A-58080A 25 December 2004 COMMERCIAL ITEM DESCRIPTION TRUCK, LIFT, FORK, DIESEL ENGINE-DRIVEN, PNEUMATIC-TIRES 4,000 POUND CAPACITY AT 24 INCH LOAD CENTER The General Services Administration has authorized the use of this Commercial Item

2、 Description (CID) for all federal agencies. 1. SCOPE. 1.1 Scope. This commercial item description covers the general requirements for a diesel engine-driven, front wheel-drive, rear wheel steer, pneumatic-tired, 4,000 pound at 24 inch load-center capacity, forklift truck. It will be used for handli

3、ng cargo in and around warehouses, loading platforms, and docks on paved or other hard surfaces. 2. CLASSIFICATION. 2.1 Classification. The operator driven vehicle covered by this CID shall be commercially available and may be modified to the extent necessary to meet this description. 3. SALIENT CHA

4、RACTERISTICS. 3.1 Safety. The operator driven vehicle shall be capable of operation within the accuracies, limits, and specifications herein. The forklift shall comply with ANSI/ITSDF B56.1 and OSHA standards in effect at the time of manufacture. A seatbelt conforming to SAE J386, and restraint devi

5、ces designed to ensure the operators upper body remains entirely within the protection of the overhead guard in the event of tip-over shall be provided. Unless otherwise specified in the contract, the final colder shall be yellow for safe operation in an indoor environment. Beneficial comments, reco

6、mmendations, additions, deletions, clarifications, etc. and any other data that may improve this document should be sent to 642 CBSG/GBEC, 460 Richard Ray Blvd, Suite 200, Robins AFB, GA 31098-1813. Since contact information can change, you may want to verify the currency of this address information

7、 using the ASSIST Online database at http:/assist.daps.dla.mil . Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-A-A-58080B 2 3.2 Environmental requirements. The engine shall start without preheating within 5 minutes, and the truck shall operate as s

8、pecified herein within 15 minutes after engine start; in any ambient temperature from 0 to 120 degrees F. The forklift shall be capable of continuous operation as specified herein at any ambient temperature up to 120 degrees F. The truck, with type C winterization, shall be capable of operating in t

9、emperatures ranging from -25 degrees F to + 125 degrees F. 3.3 Engine. A diesel fueled engine, or when specified (see 7.3), a liquid petroleum gas (LPG) fueled engine shall be provided. 3.3.1 Emissions. The vehicle emissions shall comply with the EPA regulations in effect at the time of vehicle manu

10、facture. When there is a change in EPA regulations during a contract, EPA provisions shall be consulted to determine which regulations apply (e.g. TIER 1 or TIER 2 or TIER 3). The vehicle shall comply with the emissions requirements of the destination state at the time of vehicle manufacture. 3.4 Fu

11、el System. The following shall apply: (1) When a diesel engine is furnished, all necessary filters, water separators, and other components required for diesel fuel operation shall be provided. It shall have a fuel tank of sufficient capacity to allow at least 8 hours of continuous operation. (2) Whe

12、n a LPG fuel system is provided, all necessary filters and components required for LPG operation shall be provided. It shall be of sufficient capacity to provide at least 6 hours of continuous operation. A means shall be provided to prevent fuel flow when the engine run control (ignition switch) is

13、off, or if the engine should stop running. 3.5 Starting System. The engine starter motor shall not be capable of energizing while the engine is running, or while the transmission is in a forward or reverse gear. 3.6 Transmission. A torque converter and a power-shift type of transmission shall be fur

14、nished. The transmission shall provide for positive inching control, or declutch control, that permits lifting of rated load at maximum lifting speed while the transmission control is in either forward or reverse direction, without vehicle movement. This control shall also apply the service brakes.

15、3.7 Hydraulic System. A pressure relief protection device is required along with pump(s), cylinders, control valves, filter(s), reservoir, hoses, and all other components necessary to make a complete hydraulic system. 3.8 Uprights and carriage. With no load on the forks, the seated operator shall be

16、 able to see at least one fork tip at all lift heights and fork positions. 3.9 Forks. Fork dimensions shall be 1.86 inches maximum thickness, 5.06 inch maximum width, and 42.0 ( 0.5 inch) long. Fork thickness at the tip shall be not more than 0.5 inch, and there shall be a taper on the underside of

17、the forks of not less than 14 inches. Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-A-A-58080B 3 3.10 Fork Positioner. Manually (operator) adjusted fork positioning shall be furnished. The forks shall have spacing of 12.0 inches (or less) when in m

18、ost closed position, and 32.0 inches (or more) when in most spread position. These dimensions shall be measured to the outside edges of the forks. 3.11 Side shift. Hydraulically powered side shifting shall be furnished. It shall be controlled by seated operator, with at least 4.0 inches side shift e

19、ach side of center (8.0 inches minimum total travel) with rated load on the forks. 3.12 Load Backrest. The load backrest, in conjunction with the forks and carriage, shall provide a vertical rear load guard of at least 48 inches high, measured from the load horizontally carrying surfaces of the fork

20、s. 3.13 Steering. Power steering shall be furnished. 3.14 Service Brakes. Service brakes shall be furnished. They shall conform to ANSI/ITSDF B56.1, except the maximum brake pedal force during stopping distance and drawbar drag tests shall be not more than 80 pounds. 3.15 Parking Brake. Parking brak

21、e shall conform to ANSI/ITSDF B56.1. 3.16 Electrical System. All components necessary to make a complete electrical system shall be furnished. 3.17 Instruments. The instruments, gauges, or warning indicator lights that are on the manufacturers standard commercial model shall be furnished. In additio

22、n, an unlighted hour meter capable of totaling at least 9999 hours shall be included. 3.18 External Lights. Minimum of three floodlights shall be furnished. Two in front, mounted on the upright, facing forward, and one mounted in the rear, facing rearward. 3.19 Taillight. One combination stoplight a

23、nd taillight shall be provided. 3.20 Horn. A horn shall be furnished, with the horn actuator located in the center of the steering wheel. 3.21. Operators overheard guard. The guard shall be in accordance with ANSI/ITSDF B56.1 including inside clearances. It shall also be a falling-object-protective-

24、structure (FOPS) conforming to ANSI/ITSDF B56.1. The height from the ground to the top of the overhead guard shall be not more than 86.5 inches. Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-A-A-58080B 4 3.22 Cab. When specified (see 7.3), a cab sh

25、all be furnished. It shall have FOPS capability in accordance with ANSI/ITSDF B56.1, and shall have two opening doors, and at least one fan for ventilation. There shall be sufficient window area to permit at least 250 degrees of horizontal visibility by the seated operator. The height, from the grou

26、nd to the top of the cab shall be not more than 86.5 inches. A heater and defroster with fan shall be provided. There shall be at least three wipers, one on the front windshield, one on the rear window, and one on the roof window. A commercial fire extinguisher shall be mounted on the truck in an ea

27、sily accessible location. The fire extinguisher shall be a minimum 2-1/2 pound capacity ABC type, or equivalent. The fire extinguisher shall be UL listed. 3.23 Painting. The forklift shall be primed and painted using standard commercial practices. Unless otherwise specified (see 7.3), the final colo

28、r shall be yellow. 3.24 Walkway Coating. Step surfaces shall be made of, or covered with, a non-slip material. 3.25 Lifting and Tie-down Provisions. There shall be permanently installed slinging devices that enable the truck to be lifted in its normal travel position, and tie-down devices that enabl

29、e the truck to be tied-down to the floor of the transportation media. All devices shall be capable of accepting a chain and hook with an outside diameter of 3.0 inches and shall have a structural safety factor of at least 2.0 to 1, based on static load. The notation “LIFT HERE” or “TIE DOWN” shall b

30、e stenciled, in black letters, near each lifting and tie-down device. 3.26 Identification Plate. A corrosion resistant identification plate shall be permanently installed at an easily accessible place on the truck. It shall contain the following: NOMENCLATURE: MANUFACTURES NAME: MANUFACTURERS ADDRES

31、S: MANUFACTURERS SERVICE PHONE NUMBER: MANUFACTURERS MODEL NUMBER: MANUFACTURERS SERIAL NUMBER: DATE OF MANUFACTURER: CONTRACT NUMBER: NATIONAL STOCK NUMBER: REGISTRATION NUMBER: 3.27 Performance. The truck shall be capable of meeting the following performance requirements: (1) Capability to safely

32、handle a 4,000 pound, 48 inch-per-side cube, with the center of gravity at the center of the cube. This shall be defined, and referred to in this document, as the rated load. The forklift shall be able to safely handle this rated load at all lift heights and fork side shift positions that it is capa

33、ble of attaining. Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-A-A-58080B 5 (2) Load lifting speed: Shall be capable of raising rated load at a speed of at least 55 feet per minute. (3) Load lowering speed: Not more than 80 feet per minute with ra

34、ted load on the forks and not less than 40 feet per minute with no load on the forks. (4) Right angle turn: With rated load on the forks and forklift located perpendicular to a wall, and with the front of the load against the wall, the truck shall be able to back up and make a complete right angle t

35、urn (ending up parallel to the wall) within 170 inches. (5) Travel speed: 10 miles per hour minimum, in both forward and reverse, while carrying rated load on the forks. (6) Slope ascension: With the truck facing up the slope and with rated load on the forks it shall be able to accelerate up a 20 pe

36、rcent (11 degree) slope from a dead stop. (7) Upright tilt: With no load on the truck the forks shall have at least 3.0 degrees forward tilt, and at least 6.0 degrees of rear tilt. (8) Lowest upright height (collapsed mast height): The dimension from ground to top surface of the uprights, with uprig

37、hts vertical, shall not exceed 86.5 inches maximum with no load on the forks. (9) Maximum fork lift height: At least 144.0 inches with rated load on forks and forks horizontal, when measured from ground to top surfaces of the forks. (10) Free lift height: The height that the forks can raise the rate

38、d load before the collapsed mast height is increased shall be at least 45.0 inches. (11) Drift of load: With hydraulic fluid at the ambient temperature, lift assembly shall hold rated load at maximum lift height for at least 10.0 minutes with not more than 1-3/4 inch of vertical drift, and not more

39、than 1.0 degree of rotational drift. (12) Stability: The forklift shall meet the ANSI/ITSDF B56.1 “forward stacking”, “forward travel”, “lateral stacking”, and “lateral travel” stability requirements. (13) Noise limits: The maximum allowable at the operators ear is 92 db(A). If the noise level at th

40、e operators ear exceeds 84 db(A) (85 to 92 db(A), a warning sign stating that operators hearing protection is required shall be installed at the operators station. The sign shall be as least 4 inches square, with a yellow background. (14) Electromagnetic interference (EMI): The forklift shall comply

41、 with the EMI requirements shown in Table I. Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-A-A-58080B 6 TABLE I. Electromagnetic interference (EMI) Name Description Parameters SAE J551-1 Compatibility N/A CISPR 12 b) meet appropriate performance st

42、andards, or c) subcontractors comply with this requirement. 5. PRODUCT CONFORMANCE PROVISIONS 5.1 Product conformance. The products provided shall conform to the producers own drawings, specifications, standards, and quality assurance practices and shall be the same product offered for sale in the c

43、ommercial market. The Government reserves the right to require proof of such conformance prior to first delivery and thereafter as may be otherwise provided for under the provisions of the contract. 5.2 Market Acceptability. The following market acceptability criteria are necessary to document the q

44、uality of the product to be provided under this CID. 5.2.1 Commercial. The vehicle furnished shall be, as of the date of award, the latest model (with minor modifications, as that term is defined in DoD FAR Supplement 252.211-7012, Paragraph K-85 of the solicitation) of an established product previo

45、usly produced and sold in substantial commercial quantities (exceeding the criteria at FAR 15.804-3(f)(2)(ii)(A) for at least three years. The vehicle furnished, or earlier models of it, absent minor modifications, shall have routinely been supported with spare/repair parts which were produced or so

46、ld in the normal course of business. At the time of delivery, the contractor shall furnish the Administrative Contracting Officer with verification of compliance with these requirements. Offers shall provide, as part of their proposals, the following information on the vehicle (or its earlier models

47、) being offered as a commercial item: (1) Total sales to the U.S. Government or to contractors for U.S. Government use during the three years. (2) Total sales of the item to the general public during the three years. (3) Length of time the item has been sold in the commercial market place. Provided

48、by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-A-A-58080B 8 6. PACKAGING 6.1 Packaging. Preservation, packing, and marking shall be as specified in the contract. Unless otherwise specified in the contract, the items shall be packaged according to normal comm

49、ercial practice and packed to assure acceptance by common carrier and provide product protection against loss and damage during multiple shipment, handling, and storage. Shipping containers shall be properly marked and in compliance with both national and uniform motor freight classifications. 7. NOTES 7.1 Intended use. The vehicle is intended for use in handling cargo in and around