AIR FORCE A-A-58085-1996 TRUCK LIFT FORK ELECTRIC WALKIE REACH 3000 POUND CAPACITY 150 INCH MINIMUM LIFT [Superseded AIR FORCE MIL-T-83816 CANC NOTICE 1 AIR FORCE MIL-T-83816]《24英寸.pdf

1、A-A-5O5 9999974 OL73000 T4b Beneficial comments, recommendations, additions, deletions, clarifications, etc., and any data which may improve this document should be sent to: WR-ALCLVRE, 225 Ocmulgee Court, Robins AFB GA 3 108 8- 1647 L INCH-POUND A-A-58085 29 Nov 96 SUPERSEDING 3 1 July 1990 MIL-T-8

2、38 16 COMMERCIAL ITEM DESCRIPTION TRUCK, LIFT, FORK, ELECTRIC, WALKIE REACH, 3000 POUND CAPACITY, 150 INCH MINIMUM LIFT The General Services Administration has authorized the use of this commercial item description as replacement for MIL-T-838 16. 1. SCOPE. This commercial item description covers th

3、e general requirements for a battery powered, industrial type, walking operator forklift truck. 2. SALIENT CHARACTERISTICS. 2.1 Safety. The forklift shall comply with ANSI B56.1 , OSHA, and all other applicable standards in effect at the time of manufacture. Unless otherwise specified in the contrac

4、t, the final color shall be yellow for safe operation in an indoor environment. 2.2 Environmental requirements. The forklift shall be capable of continuous operation as specified herein at any ambient temperature fiom O degrees F to 120 degrees F. 2.3 Maintainabilitv. All maintenance and servicing f

5、unctions shall be capable of being performed using common hand tools. 2.4 Lubrication. Lubrication means shall be provided for all moving parts that require periodic lubrication. The types of lubricants shall be selected from and in accordance with SAE 5754. Grease lubrication fittings shall conform

6、 to SAE J534. 2.5 Fluid level indicator. All fluid level indicators shall be located where they are accessible without danger of bums or injury to the operator. The indicators shall be in an open area, or covered by a hinged panel that can be opened and closed without the need for tools. 2.6 Hvdrau

7、lic svstem. A pressure relief protection device is required along with pump(s), cylinders, control valves, filter(s), reservoir, hoses, and all other components necessary to make a complete hydraulic system(s). 2.7 Electric motors. Motors shall be industrial type. The insulation for motors shall be

8、class By F, or H as defined in NEMA standards. AMSC N/A FSC 3930 Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-A-A-58085 9999974 0173001 982 A-A-58085 2.8 Battery. The battery shall have adequate capacity to provide not less than 8.0 hours of conti

9、nuous operation under normal industrial use. The battery mounted half connector shall be the “SB” type. 2.9 Forks. The fork and fork carrier shall conform to ANSI B56.1. Fork dimensions shall be 2.5 inches maximum thickness, 5 inches maximum width, and 35 to 42 inches in length. Fork thickness shall

10、 not exceed 0.5 inch at the tip, and there shall be a tapex on the underside of the forks not less than 14 inches long. 2.10 Fork positioner. The forks shall be capable of being laterally positioned manually without the need of tools. With the forks at their widest spacing, they shall spread at leas

11、t 27 inches, measured from the outside of the forks. With the forks at their narrowest spacing, they shall measure no more than 16 inches from outside to outside of the forks. 2.1 1 Load backrest. A metal backrest, or backrest with extension, shall be provided. There shall be no protruding bolts or

12、appendages beyond the side plane of the load backrest. The load backrest, in conjunction with fork and hanger design, shall provide a vertical rear guard at least 48 inches high measured from the load carrying surfaces of the forks. 2.12 Fork extension: Forks and load backrest shall be able to exten

13、d forward at least 24 inches from the rearmost position. 2.13 Service brakes. Service brakes conforming to ASMEIANSI B56.1 shail be hished. 2.14 Parking brake. Parking brake shall conform to ASME/ANSI B56.1. 2.15 Speed and direction controls. Speed and direction controls shall be in accordance with

14、ASME/ANSI B56.1. All load motion controls shall be self centering, that is they shall return to the neutral position when released. 2.16 m. A horn shall be furnished, with the horn actuator located within reach of the operator. 2.17 Contro 1s and insrumentation markings, All controls and instrumenta

15、tion shall be provided with position markings conforming to ASME/ANSI B56.11.3. 2.18 Indicators. The truck shall be equipped with a battery discharge indicator and an hour meter, both visible to the operator. 2.19 External lights. There shall be at least one sealed beam, 25 watts minimum, floodlight

16、 facing forward. 2.20 Painting. The forklift shall be primed and painted using standard commercial practices. The final color shall be yellow, unless otherwise specified. 2.21 Walkwav coating. Floor plates and step surfaces shall be coated with a non-slip coating compound or be furnished with a non-

17、slip metal surface in accordance with ASME/ANSI B56.1. 2.22 Electroma-etic interference (EM11 suppression. The truck shall control EM1 to meet the requirements of SAE J55 1. 2 Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-I A-A-58085 9999974 037300

18、2 819 A-A-58085 2.23 Informational aids. All stencils, decals, plates, or other similar items, that are provided on the manufacturers standard product shall be included on the forklift. This shall include, but not be limited to: rated capacity, all cautions and warnings, and all references to safety

19、 related items. 2.24 Slinginp rovisions. Slinging devices that provide a means of attaching a shackle or ring to the forklift for safe lifting shall be furnished to allow the truck to be lifted by a crane in its normal operating position. Each device shall be not more than 1.0 inch thick. The openin

20、g in the device shall be at least 3.0 inches in diameter. Each slinging device, when loaded as the truck will be picked up, shall withstand a load of 2.3 times the static load on each device. The words “LIFT HERE“ shall be stenciled near each slinging device. If possible, the slinging devices may al

21、so be used as the tiedown devices. 2.25 Tiedown provisions. Tiedown devices shall be hished that withstand the following loads: 3.0 times the unloaded truck weight in the forward and aft directions, 2.0 times the unloaded truck weight in the downward direction, and 1.5 times the unloaded truck weigh

22、t in both lateral directions. Each device shall withstand at least 1.5 times the loads in the previous sentence without breaking or rupturing. The devices shall be not more than 1 .O inch thick, and the opening in the device shall be at least 3.0 inches in diameter. The word “TIEDOWN“ shall be stenc

23、iled near each tiedown device. If possible, the tiedown devices may also be used as the slinging devices. 2.26 Identification plate. A corrosion resistant identification plate shall be permanently installed at an easily accessible location. It shall contain the following information: NOMENCLATURE: M

24、ANUFACTURERS NAME: MANUFACTURERS ADDRESS: MANUFACTURERS SERVICE PHONE NUMBER MANUFACTURERS MODEL NUMBER: MANUFACTURERS SERIAL NUMBER DATE OF MANUFACTLJRE: CONTRACT NUMBER: NATIONAL STOCK NUMBER: REGISTRATION NUMBER 2.27 Performance. The truck shall be capable of meeting the following performance req

25、uirements: (1) Rated Load: Capability to safely handle the rated load, which is defmed as a 3,000 pound, 48 inch per side cube with the center of gravity at the center of the cube. The truck shall be able to handle this load at all lift heights that it is capable of attaining. (2) Load lifting swed

26、At least 12 feet per minute with rated load on forks. (3) Load lowering speed: With rated load on forks, not more than 60 feet per minute. With unloaded (4) Right angle stacking: The truck with rated load shall be capable of right angle stacking in an aisle (5) Travel speed: Shall be capable of trav

27、eling at least two miles per hour, in both forward and (6) Brake: The brake shall be capable of holding the truck with rated load on a 15 percent grade in (7) Slope ascension: With rated load on the forks it shall be able to accelerate up a 15 percent slope (8) Upright tilt: With no load on the fork

28、s, the mast shall have a minimum forward tilt of two forks, not less than 25 feet per minute. not more than 86 inches wide, into a 56 inch wide space for the load. reverse directions, while carrying rated load on the forks. both forward and reverse directions. from a dead stop in the forward directi

29、on. degrees and a minimum rearward tilt of four degrees. Positive means shall be furnished to prevent cavitation of the tilt cylinders. 3 Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,- A-A-58085 9999974 01i3003 755 4 c A-A-58085 (9) Collapsed mast

30、hei&: Lowest upright height shall be 95.0 inches maximum with no load on the (10) Lift hew: The minimum lift height, with truck bearing rated capacity load and the uprights (1 1) Free lift height: With no load on the forks and the mast vertical, the vertical distance from the forks. fully extended a

31、nd vertical, shall be 150 inches. ground to the horizontal load carrying surfaces of the forks, without increasing the specified collapsed mast height, shall be not less than 12 inches. (12) Drift of load. With hydraulic fluid at normal operating temperature, lift assembly shall hold rated load at m

32、aximum lift height for at least 10.0 minutes with not more than 1 .O0 inch of vertical drift. (13) Stabiliu. The forklift shall meet the ASMEIANSI B56.1 “forward stacking,“ “forward travel,“ “lateral stacking,“ and “lateral travel“ stability requirements. (14) Tire loading. Under all fork loading co

33、nditions, from empty forks up to rated load, the weight on any tire shall not exceed the maximum allowed by the Tire and Rim Association Yearbook. 3. REGULATORY REQUIREMENTS. 3.1 The offeror/contractor is encouraged to use recovered materials to the maximum extent practicable, in accordance with par

34、agraph 23.403 of the Federal Acquisition Regulation (FAR). However, used, rebuilt, or remanufactured components, pieces, and parts shall not be incorporated in the forklift. 4. QUALITY ASSURANCE PROVISIONS. 4.1 Product Conformance. The products provided shall conform to the producers own drawings, s

35、pecifications, standards, and quality assurance practices and be the same product offered for sale in the commercial market. The Government reserves the right to require proof of such conformance prior to first delivery and thereafter as may be otherwise provided for under the provisions of the cont

36、ract. 4.2 Market Accentability. The following market acceptability criteria are necessary to document the quality of the product to be provided under this CID. 4.2.1 The vehicle hished shall be, as of the date of award, the latest model (with minor modifications, as that tem is defined in DoD FAR Su

37、pplement 252.21 1-7012, Paragraph K-85 of the solicitation) of an established product previously produced and sold in substantial commercial quantities exceeding the criteria at FAR 15.804-3(f)(2)(ii)(A) for at least three years. The vehicle furnished, or earlier models of it, absent minor modificat

38、ions, shall have routinely been supported with spare/repair parts which were produced or sold in the normal course of business. At the time of delivery, the contractor shall furnish the Administrative Contracting Officer with verification of compliance with these requirements. Offers shall provide,

39、as part of their proposals, the following information on the vehicle (or its earlier models) being offered as a commercial item: (1) Total sales to the U.S. Government or to contractors for U.S. Government use during the three years. (2) Total sale of the item to the general public during the three

40、years. (3) Length of time the item has been sold in the commercial market place. 5. PACKAGING. Preservation, packing, and marking shall be specified in the contract or order. 4 Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-6. NOTES. 6.1 Source of D

41、ocuments. A-A-SO5 9 9999974 0173004 b91 6.1.1 ASME/ANSI documents may be obtained from - -merican Society of Mechanics East 47th St., New York NY 10017. A-A-58085 Engineers, 345 6.1.2 SAE documents may be obtained from Society of Automotive Engineers, Inc, 400 Commonwealth Drive, Wmendale PA 15096. MILITARY INTERESTS: CUSTODIANS: Air Force - 99 Navy-SA Army-AT CIVIL AGENCY COORDINATING ACTIVITY: PREPARING ACTIVITY: AirForce: 84 AGENT: AirForce: 99 GSA-FSS PROJECT NUMBER: 3930-F036 5 Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-