AIR FORCE A-A-59757 REV B-2010 CRANE TRUCK WAREHOUSE PNEUMATIC RUBBER TIRES [Replaced NAVY MIL-C-3998 E CANC NOTICE 1 NAVY MIL-C-3998 E NAVY MIL-C-3998 D NAVY MIL-C-3998 C INT AMD .pdf

1、FSC 3950 A-A-59757B 10 February 2010 SUPERSEDING A-A-59757A 17 December 2009 COMMERCIAL ITEM DESCRIPTION CRANE TRUCK, WAREHOUSE, PNEUMATIC RUBBER TIRES The General Services Administration has authorized the use of this commercial item description as a replacement for Class A of MIL-C-3998 for all fe

2、deral agencies. 1. SCOPE 1.1 Scope. This Commercial Item Description (CID) covers the requirements for a commercial, wheel-mounted, self-propelled, rotating and telescoping boom, warehouse and industrial handling crane. 2. CLASSIFICATION. 2.1 Classification. The trucks covered by this CID shall be l

3、isted by type as shown below. The type to be furnished shall be as specified (see 3.4). Type I - Diesel powered Type II - Duel Fuel (LPG/Gas) powered 2.2 Part or Identification Number (PIN). The following PIN procedure is for government purposes and does not constitute a requirement for the contract

4、or. AA - 59757 - 1 Type: 1- Type I Diesel powered 2- Type II Duel Fuel (LPG/Gas) powered CID number AA prefix INCH-POUND Beneficial comments, recommendations, additions, deletions, clarifications, etc. and any other data that may improve this document should be sent to 642 CBSG/GBEC, 460 Richard Ray

5、 Blvd, Suite 200, Robins AFB, GA 31098-1813. Since contact information can change, you may want to verify the currency of this address information using the ASSIST Online database at http:/assist.daps.dla.mil . Provided by IHSNot for ResaleNo reproduction or networking permitted without license from

6、 IHS-,-,-A-A-59757B 2 3. SALIENT CHARACTERISTICS 3.1 Safety. The truck shall comply with UL 558, OSHA, and ASME B30.5 specifications in effect at the time of manufacture. An operators seatbelt conforming to SAE J 386, and restraint devices designed to ensure the operators upper body remains entirely

7、 within the protection of the overhead guard in the event of tip over shall be provided. 3.2 Operating temperature. The truck shall be capable of operating in temperatures ranging from -25 F to +125 F. The power source shall start within 5 minutes in any ambient temperature and with the truck stabil

8、ized at ambient temperature. 3.3 Materials. Materials shall be as specified herein. Materials not specified shall be selected by the contractor and shall be subject to all provisions of this specification. Unless otherwise specified herein, all equipment, material, and articles incorporated in the w

9、ork covered by this specification are to be new. 3.3.1 Recovered materials. The components, pieces and parts incorporated in the trucks may be newly fabricated from recovered materials to the maximum extent practicable, provided the trucks produced meet all other requirements of this specification.

10、Used, rebuilt or remanufactured components, pieces and parts shall not be incorporated in the truck. 3.3.2 Dissimilar metals. Unless suitably protected against galvanic corrosion, dissimilar metals shall not be in intimate contact with each other. 3.3.3 Drain holes. Structures shall be designed to e

11、liminate pockets where debris and water might accumulate. All structural configurations shall allow water run-off, or shall have adequate sized and placed drain holes. 3.4 Power source. 3.4.1 Diesel (Type I). The truck shall be powered by a standard, commercial, diesel engine. The engine shall opera

12、te on diesel fuel in accordance with A-A-52557 without detrimental effects on the engine, or its performance. 3.4.2 Duel Fuel (Type II). When specified (see 7.2), the truck shall be powered by a standard, commercial, duel fuel (Liquefied Petroleum Gas/Gasoline) engine. 3.5 Fuel system. The truck sha

13、ll have all necessary filters, water separators, and components required for operation. The truck shall have a fuel tank of sufficient capacity to allow at least eight hours of continuous operation. 3.6 Starting system. The starter switch shall not activate the engine starter while the engine is run

14、ning, nor when the engine is not running and the transmission is in any forward or reverse gear. The starter switch shall only operate when the transmission is in the “neutral” or “park” positions. Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-A-A-

15、59757B 3 3.7 Transmission. A torque converter and a powershift type of transmission shall be furnished, with at least three speeds forward and one speed reverse. 3.8 Hydraulic system. A pressure relief protection device is required along with pump(s), cylinders, control valves, filter(s), reservoir,

16、 hoses, and all other components necessary to make a complete hydraulic system. In the event of hydraulic system damage or failure, a means to prevent the boom from automatically lowering/retracting/tilting shall be provided. The hydraulic system shall prevent the load from falling more than 0.5 inc

17、hes after system failure. A manual override system shall be provided to allow for safe load removal. 3.9 Visibility. Truck manufacture shall have a side-view of the truck showing sight lines for a 95th percentile male and a 5th percentile female. The visibility shall conform to the standard visibili

18、ty available in the industry. 3.10 Steering. Power steering, with emergency steering in the event of power failure, shall be furnished. 3.11 Service brakes. The service braking system shall the commercially available system provided by the manufacturer. The service brakes shall be capable of bringin

19、g the crane to a complete safe stop in accordance ASME B30.5. Not more than 80 pounds of force on the brake pedal shall be required to meet the requirements of ASME B30.5. 3.12 Parking brake. Parking brake(s) shall hold, but not necessarily stop the truck without rated load when the truck is stopped

20、 on a 15 percent grade in both the ascending and descending position. The parking brakes shall be operated by hand or foot controls and is located within reach of the seated operator. The brake shall have a locking device. The force required to pull the hand lever when setting the brake shall not ex

21、ceed 35 pounds. The parking brake shall be independent from the service brakes. 3.13 Electrical system. A 12 or 24 volt direct current (VDC) electrical system shall be furnished. The electrical system shall consist of all electrical components necessary for operation of the truck. The truck shall ha

22、ve sufficient electrical grounding to prevent static discharge. 3.14 Backup alarm. An audible backup alarm shall be furnished. The alarm shall automatically activate when the transmission selector is placed in reverse. 3.15 Instruments and controls. In addition to the instruments supplied on the sta

23、ndard commercial truck, an hour meter shall be installed in the instrument panel. Except the hour meter, all instruments shall illuminate. All load motion controls shall be right hand operation controls and of the self-centering type, i.e., controls shall return to the neutral position when released

24、. All controls shall be located within easy reach of the operator in the operators cab. All controls shall be clearly marked as to their use and function. 3.16 Lighting. A minimum of (2) headlights, (1) boom-mounted light, a variable light to illuminate the working area, and 4-way hazard warning lig

25、hts shall be furnished. Tail light(s) Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-A-A-59757B 4 and brake stop light(s) shall be installed. Individual operator controlled switches shall be provided. 3.17 Horn. An electric or air horn shall be prov

26、ided. The horn may be hand or foot actuated. 3.18 Operators overhead guard. An overhead guard shall be provided to protect the operator from falling objects. 3.19 Cab. The truck shall be equipped with an enclosed cab and shall have a door with at least one window, which can be opened for ventilation

27、. The door shall be provided with hinges that can be serviced without door removal. In addition to the door window, the cab shall be furnished with a front windshield, rear window, and side windows. The windshield and all windows shall be safety glass. Dual rear view mirrors shall be provided. The c

28、ab interior shall be furnished with water-resistant non-absorbent thermal insulation. A commercial fire extinguisher shall be mounted on the truck in an easily accessible location. The fire extinguisher shall be a minimum 2-1/2 pound capacity ABC type, or equivalent. The fire extinguisher shall be U

29、L listed. 3.20 Windshield wipers. There shall be at one wiper on the front window and one wiper on the rear window. 3.21 Winterization. At a minimum, the following items shall be provided. 3.21.1 Engine coolant heater. An engine coolant heater shall be installed in the engine block or lower coolant

30、inlet hose. A coolant-circulating pump, driven by a 110 volt or 220 volt alternating current motor, shall be provided when a coolant inlet hose heater is furnished. The heater shall have adequate capacity to maintain engine coolant at a temperature of +10 F in an ambient temperature of -25 F. It sha

31、ll be controlled to limit engine coolant to not more than 150 F. 3.21.2 Engine oil heater. An engine oil heater with adequate capacity to maintain engine oil at a temperature of at least +10 degrees F in an ambient temperature of -25 F shall be furnished. It shall be controlled to limit engine oil t

32、emperature to not more than 150 F. 3.21.3 Battery heater. A battery heater shall be provided. It shall have adequate capacity to maintain battery electrolyte at a temperature of at least +10 F in an ambient temperature of - 25F, and shall have a thermostat to limit temperature of the electrolyte to

33、not more than +80F. 3.21.4 Cab. The cab shall meet the requirements of 3.19, and shall also contain thermal insulation, if necessary, to meet the heating requirements of 3.21.5. 3.21.5 Heater and defroster. The heater shall be of sufficient capacity to maintain a temperature of +40 F at cab floor le

34、vel in an ambient temperature of -25 F. 3.21.6 Cold starting aid. A cold starting aid such as glow plugs shall be furnished. 3.21.7 Antifreeze. Engine coolant shall be protected to -25 F. Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-A-A-59757B 5 3

35、.22 Performance. 3.22.1 Minimum lifting capacities. The boom lengths referenced below are measured from the centerline of rotation to the centerline of the load. Also, the load capacities referenced below should remain constant throughout 360 degrees of boom rotation. 3.22.1.1 With outriggers extend

36、ed. The crane shall be capable of lifting 10,000 pounds with the boom retracted to 8 feet. The crane shall be capable of lifting 4,000 pounds with the boom extended to 18 feet. 3.22.1.2 Without outriggers extended (on rubber). The crane shall be capable of lifting 5,000 pounds with the boom retracte

37、d to 8 feet. The crane shall be capable of lifting 1,000 pounds with the boom extended to 18 feet. 3.22.2 Travel speed. The crane without load shall be capable of attaining and maintaining a travel speed on level, paved roads of not less than 15 mph. 3.22.3 Gradeability. The crane without load shall

38、 be capable of ascending a 15 percent grade on hard packed surfaces, without engine stall, in forward gear at a speed of not less than 2 mph. 3.22.4 Noise limits. Maximum allowable noise level shall not exceed 84dB(A) at the operators ear. If the noise level at the operators ear exceeds 84 dB (A) (8

39、5 to 92 dB (A), a permanent warning decal or placard shall be installed inside the cab clearly visible to the operator. Noise level limits that exceed 92dB(A) are not acceptable. 3.22.5 Electromagnetic interference (EMI). The truck shall comply with EMI requirements of SAE J551-1, CISPR 12 minimum l

40、ug opening diameter shall be three inches. Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-A-A-59757B 8 4. REGULATORY REQUIREMENTS 4.1 Recycled, recovered, or environmentally preferable materials. Recycled, recovered, or environmentally preferable ma

41、terials should be used to the maximum extent possible provided that the material meets or exceeds the operational and maintenance requirements, and promotes economically advantageous life cycle costs. The offeror/contractor is encouraged to use recovered materials to the maximum extent practicable,

42、in accordance with paragraph 23.403 of the Federal Acquisition Regulation (FAR). 4.2 Green Procurement Program. Green Procurement Program (GPP) is a mandatory federal acquisition program that focuses on the purchase and use of environmentally preferable products and services. GPP requirements apply

43、to all acquisitions using appropriated funds, including services and new requirements. FAR 23.404(b) applies and states the GPP requires 100% of EPA designated product purchase that are included in the Comprehensive Procurement Guidelines list that contains recovered materials, unless the item canno

44、t be acquired: a) competitively within a reasonable timeframe; b) meet appropriate performance standards, or c) subcontractors comply with this requirement. 5. PRODUCT CONFORMANCE PROVISIONS 5.1 Product Conformance. The products provided shall meet the salient characteristics of this commercial item

45、 description, conform to the producers own drawings, specifications, standards, and quality assurance practices, and be the same product offered for sale in the commercial marketplace. The government reserves the right to require proof of such conformance. 5.1.1 The contractor shall conduct a user d

46、emonstration of the first unit produced under the contract. This demonstration shall include operation of the vehicle and all supporting data required to meet compliance with this specification. 5.2 The contracting officer has the option of accepting or rejecting the product. 6. PACKAGING 6.1 Preser

47、vation, Packaging, Labeling and Marking. Unless otherwise specified (see 7.2), the preservation, packaging, and packing shall be to a degree of protection to preclude damage to containers and/or contents thereof under normal shipping conditions, handling, etc. This involves shipment from the supply

48、source to the receiving activity, and reshipment from the receiving activity. The preservation, packaging, and packing shall conform to applicable carriers rules and regulations. Intermediate and exterior package quantities, labeling and marking shall be as specified in the contract and/or order. 7.

49、 NOTES. 7.1 Sources of documents. Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-A-A-59757B 9 7.1.1 Military Specifications, Standards, and Handbooks referenced herein may be obtained at http:/assist.daps.dla.mil or available from the Standardization Documents Order Desk, 700 Robbins Ave, Bldg 4, Section D, Philadelphia, PA 19111-5094. 7.1.2 Am