AIR FORCE MIL-C-18387 F (2)-1988 CLOTH TWILL COTTON FIRE RETARDANT TREATED《防火阻燃处理棉斜纹布》.pdf

1、MIL-C-18 38 7F AMENDMENT 2 10 November 1988 SUPERSEDING AMENDMENT 1 28 September 1978 h4lLlTARY SPECIFICATION CLOTH, TWILL, COTTON, FIRE RETARDANT TREATED This amendment forms a part of MIL-C-l8387F, dated 26 July 1968, and is approved for use by all Departments and Agencies of the Department of Def

2、ense. PAGE 1 SECTION 2, APPLICAT3L.E DOCUMENTS, delete and substitute: * “2. APPLICABLE DOCUMENTS “2.1 Government documents “2.1.1 Specifications, standards. The following specifications, standards form a part of this document to the extent specified herein. Unless otherwise specified, the issues of

3、 these documents are those listed in the issue of the Department of Defense Index of Specifications and Standards (DODISS) and supplement thereto, in the solicitation (see 2.4.1 and 6.2). SPECIFICATIONS FEDERAL, V-T-276 Thread, Cotton PPP-P-1134 Packaging and Packing of Cotton and Cotton-Synthetic F

4、iber Blend Fabrics (Excluding Duck Fabrics) STANDARDS FEDERAL FED-STD-4 Glossary of Fabric Imperfections FED-STD-191 Textile Test Methods FSC 8305 AMSC NIA 1 of 5 DISTRIBUTION STATEMENT A. Approved for public release; distribution is unlimited. . Provided by IHSNot for ResaleNo reproduction or netwo

5、rking permitted without license from IHS-,-,-MIL-C-L37F (2) 3 7777706 03L251 5 MIL-C-1838 7F Ah4ENDMENT 2 PAGE 1 “2.2 Non-government publications. The following documents form a part of this document to the extent Specified herein. Unless otherwise specified, the issues of the documents which are Do

6、D adopted are those listed in the issue of the DODISS speci- fied in the solicitation. Unless otherwise specified, the issues of documents not listed in the DODISS are the issues of the non-government documents which are current on the date of the solicitation (see 2.4.2 and 6.2). FEDERAL TRADE COMM

7、ISSION Rules and Regulations Under the Textile Fiber Products Identification Act “2.3 Order of precedence. In the event of a conflict between the text of this docu- ment and the references cited herein, the text of this document takes precedence. Nothing in this document, however, supersedes applica

8、ble laws and regulations unless a specified exemption has been obtained. “2.4 Sources of documents “2.4.1 Government specifications. and standards. Copies of the referenced federal fense Single Stock Point, Commanding Officer, Naval Publications and Forms Center, 5801 Tabor Avenue, Philadelphia, PA

9、19120-5099. For specific acquisition functions, these documents should be obtained from the contracting activity or as directed by the contracting activity. “2.4.2 Non-eovernment publications. Non-government documents are generally avail- able for reference from libraries and technical groups. The d

10、ocuments listed may be obtained as follows: (Application for copies should be addressed to the Federal Trade Commission, Washington, D.C. 20580.)” and military specifications, and standards are available from the Department of De- f. i i i 2 Provided by IHSNot for ResaleNo reproduction or networking

11、 permitted without license from IHS-,-,-MIL-C-38387F (2) 83 9799906 0383252 7 I MIL-C-18387F AMENDMENT 2 ( PAGE 2 3.2, delete and substitute: “3.2 First article inspection. When specified (see 6.2), before production is com- menced, 1 yard of the desized, mercerized dyed cloth and 5 continuous yards

12、 full width of the finished (fire retardant) cloth shall be submitted or made ready for the contracting officer or his authorized representative for inspection. The (fire retardant) treatment used for the finished cloth shall be identified in sufficient detail for recogni- tion as an approved type.

13、The first article sample shall be manufactured by the sup- plier in the same facilities to be used for the manufacture of the production items. The approval of the first article samples authorized the commencement of production but does not relieve the supplier of responsibility for compliance with

14、all applicable provisions of this specification.” PAGE 3 * TABLE I, “Requirement” column: Line 3: Delete “18 minimum to” Lines 13 and l4: Delete “6.0” and substitute “4.0”. PAGE 5 4.1 and 4.1.1, delete and substitute: chase order, the contractor is responsible for the performance of all inspection r

15、equire- ments as specified herein. Except as otherwise specified in the contract or purchase order, the contractor may use their own or any other facilities suitable for the perform- ance of the inspection requirements specified herein, unless disapproved by the Gov- ernment. The Government reserves

16、 the right to perform any of the inspections set forth in the specification where such inspections are deemed necessary to assure sup- plies and services conform to prescribed requirements. * “4.1 Responsibilitv for inspection. Unless otherwise specified in the contract or pur- * “4.1.1 Remonsibilit

17、v for compliance. All items shall meet all requirements of sec- tions 3 and 5. The inspection set forth in this specification shall become a part of the contractors overall inspection system or quality program. The absence of any inspec- tion requirements in the specification shall not relieve the c

18、ontractor of the responsibil- ity of ensuring that all products or supplies submitted to the Government for accep- tance comply with all requirements of the contract. Sampling in quality conformance does not authorize submission of known defective material, either indicated or actual, nor does it co

19、mmit the Government to acceptance of defective material.” 3 Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,- NIL-C-L387F (2) 3 777770b O383253 7 111 MIL-(2-1838 7F AMENDMENT 2 PAGE 5 4.2, delete and substitute: * “4.2 Classification of inspections. T

20、he inspection requirements specified herein are classified as follows: a. First article inspection (4.2.1) b. Quality conformance inspection. (4.2.2) .” 4.2.1 and 4.2.2, delete and substitute: * “4.2.1 First article inspection. The sample of finished cloth submitted in accordance with 3.2 shall be v

21、isually examined for appearance, color and finish, and shall be tested for applicable physical and chemical properties. Tests shall be in accordance with methods specified in 4.5. “4.2.2 uality conformance inspection. The examinations and test comprising quality conformance inspection shall be as sp

22、ecified in 4.3, 4.4 and 4.5.” PAGE 7 * “4.5, line 2: Delete ”CCC-T-191” and substitute “FED-STD-191”. PAGE 8 TABL;E II, “Test Method” column, lines 17 and 18: Delete “5132” and substitute “ 5 1 34” . 4 Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-

23、MIL-C-18 387F AMENDMENT 2 (- PAGE 11 6.5, add: 6.5 Changes from previous amendment. The margins of this amendment are marked with an asterisk or vertical lines to indicate where changes (additions, modifications, corrections, deletions) from the previous amendment were made. This was done as a conve

24、nience only and the Government assumes no liability whatsoever for any inaccu- racies in these notations. Bidders and contractors are cautioned to evaluate the re- quirements of this document based on the entire content irrespective of the marginal notations and relationship to the last previous ame

25、ndment. Custodians: Air Force - 11 Army - GL Navy - AS Review activities: Air Force - 82, 99 Navy - NU I(- Preparing activity: Air Force - 11 Project No. 8305-0242 User activities: Air Force - 45 Navy - MC 5 Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-