AIR FORCE MIL-C-4294 A-1979 CLOTH TWILL NYLON《尼龙斜纹布》.pdf

1、b .( t ! MIL-C-4294AIUSAF) 24 September 1979 SUPERSEDIN MIL-C-4294(USAF) 3 April 1952 . MILITARY SPECIF.ICATION CLOTH, TWILL, NYLON This specification is approved for use by the Air Force Materials Laboratory, Department of the Air Force, and is available for use-by. all Departments and Agencies of

2、the Department of Defense. . I. SCOPE 1.1 Scope. This specification covers continous filament nylon fabric of several weights for use in aviation ground clothing. 1.2 Classification. The cloth covered by this specification shall be of the following types and classes as specified see.6.2): . Type I -

3、 3.30 ounce8 per square yard, nominal weight. Class A - Finished natural. Class B - Water resistant treatment. Type II - 5.40 ounces per square yard, nominal weight, Class A - Finished natural. Class B - Water resistant treatment. Class C - Finished natural - heavily calendered. Class D - Water resi

4、stant treatment - heavily calendered. I ! f Beneficial comments (reoomendations, additions, deletion81 and any pertinent data which may be of use in improving this document should be addressed to: Air Force Materials Laboratory, WPAFB, OH 45433 by using the self-addressed.Standardization Document Im

5、provement Proposal DD Form 1426) appearing at the end of this document or by letter. FSC 8305 . THIS DOCUMENT CONTAINS / PAGES. . , , 1 - - _ - - -, Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-flIL-C-Lt27qA 83 7777906 03750Lt2 T I Y 6 ! i I I I I

6、 1 I I i i I I I 1 i I I ! ! i l j , i 1 i ! i j I MIL-C-4294A(USAF) 2. APPLICABLE DOCUMENTS 2.1 Issue8 of documente. The following documents of the issue in effect on date of invitation for bid8 or requsaet for proporal form a part of this dpecifiaation to the extent specified hepein. SPECIFICATION

7、S FEDERAL PPP-P-1133 -Packing and Packing of Synthetic Fiber Fabrics STANDARDS FEDERAL FED- STD- 4 -Qiosaary of Fabric Imperfections FED-STD-191 -Textile Test Methode. MI LI TARY MIL-STD-105 ! -Sampling Procedures and Tables for Inspection by Attri.butes (Copies of specifications, standarda, drawing

8、s, and publications required by contractors in connection with specific procurement functions should be obtained from the procuring activity or as directed by the contracting officer. 1 2.2 Other Dublications. The following documents form a part of this specification to the extent specified herein.

9、Unless otherwise indicated, the issue in effect on the dato of invitation for bids or request for proposal shall apply. Textile Fiber Products Act (Copies may be obatained from the Federal Trade Commission, Washington, D.C. 20580.) 3. REQUIREMENTS 3.1 Standard samDla. The finished aloth shall match

10、the standard sample for shade and shall be equal to or better than the standard samples with respect to all characteristics for which the standard sample is referenced (see 6.3). 2 Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-c - 3.2 First article

11、. When specified (see 6.21, the supplier shall furnish a sample for first article inspection and approval. 3.3 Material. 3.3.1 Nylon yarn. prepared fPom hexamethylene diamine and adipic acid or its derivatives. It shall have a minimum melting point of 244C (471F). both types shall be 70 denier. Type

12、 1 and 200 denier for Type II. The nylon yarn shall be a bright luster polyamide The warp yarn for The filling yarn shall be 100 denier for 3.4 Physical reauirements. The finished cloth shall conform to the physical requirements of Table I when tested as specified in 4.5. 3.5 Finish. 3.5.1 TYDe I. T

13、ype I cloth shall be finished to meet the requirements as stated: Class A - Finished smooth and free from wrinkles. Class B - Finished smooth and free from wrinkles and given a durable water repellent treatment to give an original Spray Rating of 100 and a Spray Rating of at least 70 after three lau

14、nderings or three dry cleanings, when tested in accordance with 4.5. 3.5.2 Type II. Type II cloth shall be finished to meet the requirements as stated: Class A - Finished smooth and free from wrinkles. Class B - Finished smooth and free from wrinkles and given a durable water repellent treatment to

15、give an original Spray Rating of 100 and a Spray Rating of at least 70 after three . launderings or three dry cleanings, when tested in accordance with. 4.5. Class C - Finished smooth and free from wrinkles and heavily caIendered. Class D - Finished smooth and free from wrinkles, heavily calendered

16、. and given a durable water aepellent treatment to give an original Spray Rating of 100 and a Spray Rating of at least 70 after three launderings or three dry cleaningg, when tested in accordance with 4.5. 3 Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IH

17、S-,-,-MIL-C-4274A 3 U 777770b 0375044 3 I MITr C-4 294A (USAF ) n U ai a m t-. ri N U r c1 c: U c CI ul 0 E 03 (LE - -6.4 L no al t- a I ci cn .A A -in U C 3 O icF Y c E 3 a -6.4 e c? Kc: .d L 6.4 ax ill I- - ul c 4 3 e 4 ul -c cim C !4 .r( .r( U pi u, n -CI O C - w I- CI z Provided by IHSNot for Re

18、saleNo reproduction or networking permitted without license from IHS-,-,-i -c 3.6 Residual shrinkage. The residual shrinkage of the cloth, when tested in accordance with 4.5, shall not be more than 2 percent in the warp direction and shall not be more than 1-1/2 percent in the filling direction. 3.7

19、 -fibrous materials. percent of oils, sizing and non-fibrous matter when extracted with chloroform in accordance with 4.5. The cloth shall not contain more than 3 3.7.1 pB. The cloth shall be so that the pH of the water extract shall be not lower than 6.8 nor higher than 8.0 when tested in accordanc

20、e with 4.5. 3.8 Weave. The cloth shall be woven as a 2 up 2 down right hand twill, except that at the contractors option, the weave of Type II cloth may be a 2 up 1 down right hand twill. 3.9 Width. The width, unless otherwise specified, shall be minimum of 40 inches inclusive of selvages. 3.10 Colo

21、r. Unless otherwise specified by the contract or purchase order (see 6.21, the cloth shall be furnished in Sage Qreen, Shade No. 1511. 3.10.1 Matchinq. viewed under artificial daylight having a color temperature of 7500 degrees Kelvin and shall be a good approximation to the standard shade under The

22、 color shall match the approved standard shade when * incandescent lamplight at 2800 degrees Kelvin. 3.10.2 Colorfastness, The finished cloth shall shown fastness to laundering, light, dry cleaning, and perspiration equal to or better than the standard sample. show a minimum of good for each charact

23、eristic. . When a standard is not available, the cloth shall 3.11 Fiber identification. Each roll of cloth shall be labeled OP ticketed for fiber content in accordance with the Textile Fiber Products . Identification Act. 3.12 Workmanship. The finished cloth shall conform to the quality established

24、by this specification. The demerit points per 100 square yards, when calculated as. specified in Section 4, shall not exceed the established maximum point value. 4. QUALITY ASSURANCE PROVISIONS 5 Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,- MIL-C

25、-4299A 83 7979706 0375096 7 I .r * MIL-C-4294A(USAF) 4.1 Responsibility for inspection. Unless otherwise specified in the contract, the contractor is responsible for the performance of all inspection requirements as specified herein. fied in the contract, the contractor may use his own or any other

26、facilities suitable for the performance of the inspection requirements specified herein, unless disapproved by the Qovernment. The Government reserves the right to perform any of the inspections set forth in the specification where such inspections are deemed necessary to assure supplies and service

27、s conform to prescribed requirements. Except as otherwise speci- 4.2 Preacceptance inspection. (When applicable.) 4.3 Inspection for acceptance. InEpection shall be in accordance with the provisions of MIL-STD-165, except where otherwise indicated. 4.3.1 Examination of end item. Defects found during

28、 the examination shall be clasified in accGrtxnce with 4.3.1.1, 4.3.1.2, and 4.3.1.3. 4.3.1.1 Yard-by-yard examination. Each roll in the sample shall be examined on the face side only. When the total yardage in the roll does not exceed 100 yards, the entire yardage in the roll shall be examined. Whe

29、n the total yardage in the roll exceeds 100 yards, only 100 yards shall be examined. All defects as defined in Section III of FED-STD-4, which are clearly noticeable at normal inspection distance (3 feet), shall be 8cored and agsigned demerit points as listed in 4.3.1.1.1, except that only those slu

30、bs and knots which exceed the maximum limit shown in Figure 3 of FED-STD-4 shall be scored. No linear yard (increments of 1 yard on the measuring device on the inspection machine) from any one roll within the sample shall be penalized more than 4 points. The sample size shall be 20 rolls selected fr

31、om 20 containers. The lot shall be unacceptable if the points per 100 square yards of the total yardage examined exceeds 30.0 points. The lot shall be unacceptable if the points per 100 square yards of two or more individual rolls exceed 40.0 points. exceeds 30.0 points per 100 square yards, a secon

32、d sample of 20 rolls ahall. be examined only or individual roll quality examination. shall be unacceptable if one or more rolls in the second sample exceeds 30.0 points per 100 yards. roll quality shall be as follows: If one roll The lot Point computation for lot quality and individual Total points

33、scored in sample X 3600 = Points per 160 Contracted width of cloth (inches) x total yards inspected square yards 4,3.1.1.1 Demerit points. Demerit points shall be assigned as follows: For defects 3 inches or less in any dimension - one point Far defects exceeding 3 inches, but no exceeding 6 For def

34、ects exceeding 6 inches, but no exceeding 9 For defects exceeding 9 inches in any dimension - four points inches in any dimension - two points inches in any dimension - three points 6 Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-i + NOTE: The foll

35、owing defects when present shall be scored four points for each yard in which they occur, Baggy, ridgy or wavy cloth Width less than specified Purr dye penetration, mottled, streaky, or cloudy Holes, cuts, tears, open places. 4.3.1.2 Examination for shade. During the yard-by-yard examination, each r

36、oll in the sample shall be examined for shade. Any roll in the sample off-shade, shaded side to side, side to center or end to end shall be cause for rejection of the entire lot represented by the sample. 4.3.1.3 Examination for compliance with the rules and regulations under yard-by-yard examinatio

37、n, each roll in the sample shall be examined for conformance to the Rules and Regulations under the Textile Fiber Product Identification Act. Each roll not labeled or ticketed in accordance with this act shall be a defect, The lot shall be unacceptable if two or more of these defects occur. the Text

38、ile Fiber Products Identification Act. During the 4.4 Examination of preparation for delivery requirements. An examination shall be made in accordance with the provisions of PPP-P-1133 to determine the packaging, packing and marking comply with the Section 5 requirements of this specification. 4.5 T

39、esting of the end item. The methods of testing specified in FED-STD-191, wherever applicable, and as listed in Table II shall be followed. The physical and chemical values specified in Section 3, except where otherwise specifie, apply to the average of the determinations made on sanple unit for test

40、 purposes as specified in the applicable test method. The sample unit shall be four continuous yards, full width of the finished cloth. All test reports contain the individual values utilized in expressing the final results. The sample size shall be as shown in the list below. The lot size shall be

41、expressed in units of one yard. The lot shall be unacceptable if one or more sample units fail to meet any requirement specified. 0 Lot Size (Yards) Sample Size a00 or less 801 up to and 22,001 and over including 22,080 2 3 5 7 Provided by IHSNot for ResaleNo reproduction or networking permitted wit

42、hout license from IHS-,-,-MIL-C-qZYqA 83 777770b 0375048 O W F h!IL-C-4204A(USAF) 4.6 water resistance. The spray rating tests shall be conducted upon cloth of Type I, Class B and Type II, Clasees B and D, in accordance with Method No. 5526 of FED-STD-191. After determination of original spray ratin

43、gs, the same apecimens, prepared by cutting 8 by 8 inch squares of the cloth, are tested for #pray rating after being subjected to three dry cleanings, conducted in accordance with Method No. 5508, and also tested for spray rating after being subjected to three launderings conducted in accordance wi

44、th Method No. 5614, except that the color transfer cloth of 4.5 of Method No. 5614 shall be omitted. 4.7 Shrinkage-boil test. After conditioning for not legs than four hours, an 18-inch square shall be marked on a 20-inch square specimen by neans of a template, using indelible ink. A metal tub of ad

45、equate size to accommodate the specimen prepared as described below shall be filled to within three inches of the top with water which shall then be heated to a boil. The sample for the Boil Test shall be prepared by joining the two sides cut filling-wise so as to form a loop which is threaded over

46、a glass rod or tube 1/4 inqh in diameter by 21 inches long, A hold down weight formed of a 1/4 inch diameter glass tube or rod approximately 21 inches in length and having a weight of 50 grams plus or minus 5 gram shall be introduced into the cloth loop. A glass rod or tube resting across the tub to

47、p shall support the cloth loop entirely below the surface of the water by wires connecting to the ends of the upper 21 inch tube or rod. The sample shall be supported so that the slight tension of the hold-down weight shall apply in the warp direction, and the cloth loop shall hang freely in the bat

48、h. The sample shall then be subjected to the action of the boiling water bath for a period of 15 minutes. It shall then be removed from the tub and allowed to drain for a few minutes, opened out and then placed flat on a horizontal screen to dry. After the specimen ia thoroughly dry, it shall be exp

49、osed for at least four hours to the standard atmosphere and then be measured in three places in the warp direction and three places in the filling direction, and the amount of shrinkage recorded. 5. PACKAGIN 5.1 Put-up and packaging,. Packaging shall be Level A or C (see 6.2). 5.1.1 Levels A anc C. The cloth, put up as specified, shall be packaged in accordance with the applicable requirements of PPP-P-1133. 5