AIR FORCE MIL-C-6590 C-1985 CLOTH PILE (SYNTHETIC MOUTON KNITTED)《(合成羊皮针织)绒面布》.pdf

1、MIL-C-6590C 83 m 9999906 0425185 9 m MI L-C-6590C (USAF) MIL-C-6590B( USAF) . 22 Jan 85 13 November -1968. MI LITARY SPEC I FICA-TI ON CLOTH, PILE (SYNTHETIC MOUTON, KNITTED) This specification is approved for use by all Departments and Agencies of the Department of Defense. 1. SCOPE * 1.1 Scope. Th

2、is specification covers the requirements for a simulated furli ke garment material of knitted mouton. 1.2 Classification. The cloth shall be of the following types as specified by the procuring activity: Type Type II - 100 percent acrylonitrile copolymer vinyl chloride, pile I - 100 percent acrylic,

3、 pile fiber. fiber. 2. APPLICABLE DOCUMENTS * 2.1 Government documents. * 2.1.1 Specifications and standards. Unless otherwise specified, the following specifications and standards of the issue listed in that issue of the Department of Defense Index of Specifications and Standards (DoDISS) specified

4、 in the solicitation form a part of this specification to the extent specified herein. SPECIFICATIONS FEDERAL PPP-P-1133 Packaging and Packing of Synthetic Fiber Fabrics STANDARDS MI L ITARY MIL-STD-105 MIL-STD-129 MIL-STD-147 Sampling Procedures and Table for Inspection by At tri butes Marking for

5、Shipment and Storage Pal letized and Containerized Unit Leads 40 Inch X 48 Inch Pallets, Skids, Runners or Pallet Type Base Beneficial comnents (recomendati ons, addi ti ons , deletions) and any perti nent data which may be of use in improving this document should be addressed to: the Engineering Di

6、vision, San Antonio Air Logistics Center/MMEDO, Kelly AFB, TX 78241 by using the self-addressed Standardization Document Improvement Proposal (DD Form 1426) appearing at the end of this document or by letter. FSC 8305 Provided by IHSNot for ResaleNo reproduction or networking permitted without licen

7、se from IHS-,-,-MfL-C-654C 83 H 949990b OYi51i8b O H MICC-65(H)C( USAF) MIL-STO-1491 Glossary of Knitting Imperfections FEDERAL FED-STD-191 Textile Test Methds (Copies f specifications, standards, handbooks, drawings, and publications required by manufacturers in connection with specific acquisition

8、 functions should be obtained from the contracting activity or as directed by the con- tracting officer.) * 2.2 Other publications The folloiuing document (s) form a part of this specification to the extent specified herein, The issues of the documents which are indicated as DoD adopted shall be the

9、 issue listed in the current DoDISS and the supplement thereto, if applicable. Rules and Regulations Under the Textile Fi ber Products Identification Act (Copies may be obtained free of charge from the Federal Trade Commission, Was hing ton I 0 . C . 20580) . * 2.2,l Order of precedence. In the even

10、t of a conflict between the text of this specification and the references cited herein, the text of this specification shall take precedence, 3, REQUIREMENTS 3,l Standard, sample. Unless otherwise specified, the cloth shall be equal to, or better than the standard sample with respect to all characte

11、r- istics for which the standard is referenced (see 6.3), * 3,2 Material. * 3.2.1 Backing, The backing shall be made from undyed spun fibrillated filamented polypropylene yarn or filamented polypropylene/cotton blend yarn. * 3,2.1,1 Cotton. The cotton yarn shall be thoroughly cleaned, well carded, d

12、rawn and evenly spun into a suitable yarn site for the backing. * 3.2.2 m. The plle fiber shall be carded and drawn to form a smooth even roving, inserted into the material as shown on figure 1. The pile fibers shall be 11 ounces per square yard minimum of the total cloth weight when tested as speci

13、fied in Table Y. * 3.2.3 Eacking_mwound. The backing compound shall consist of a vinyl acetate resn or acrylic resin suitably compounded to form a flexible backing with good resistance to dry cleaning solvents. When tested as specified in Table Y (footnote i/), 3.3 Ground fabric. The ground fabric s

14、haT1 be made of cotton yarn. * 3.4 Physical requiremen.ts, The material shall confom to the properties specified in Table I when tested as specified in 4.3. r b I f 2. Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-MIL-C-b570C 83 MIL-C-6590C(USAF) m

15、 qwwob 02517 2 = 4 1. Shows position of backing yarns in relation to pile yarns in knitted cloth. 2. Shows pile yarn of synthetic mouton after being sheared and in relation to backing yarn. 3. Indicates formation of wales and courses in backing material. 4. Indicates interlacing of pile yarn into ba

16、cking yarns. FIGURE 1. Pile and backing construction. c 3 Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,- flIL-C-aS40C 83 7443406 OYZ5388 Y W MIL-C-6590C (USAF) * 3.4.1 Resi-. The backing material shall show no signs of blocking when tested as speci

17、fied in Table V. * 3.4.2 Flexibility, The backing material shall not crack or break when I= teated as specified in Table V (footnote A/) 3 e 5 Dimensions. 3.5.3 w. ing activity (sea 6.2). The width of the cloth shall be as specified by the procur- 3.5.2 Length of piece, Length shall be not less than

18、 30 continuous yards. Lengths lese than 30, but not less than 10 continuous yards may be accepted by the procuring activity under limitations and conditions set forth in the invitation for bids (see 6.2), * 3.5.3 Length o . Rolls shall contain one continuous piece, free from splices, except where sh

19、ort lengths are permitted, two or more short lengths may bo put up in one roll, provided there is no splice and provided the roll complies with the applicable weight limitations o PPP-P-1153. 3*4, Coloyl Except when otherwise specified, the color shall be sage green, Air Horca shade 1.538, to match

20、the standard sample (see 6.3). 3.U.l Matching, The color shall match the standard sample when viewed The from a poiition normal- totliecloth surface and under natural (north sky) day- light or artificial light having a color temperature of 7500“ Kelvin. 60105: shall be a good approximation to the st

21、andard sample under incandescent lamplight at 2880“ Kelvin. the aampl-e Es be compzred shall be brushed and viewed in the same direction relative to construction and angle of lighting. * 3.6.2 Co1orfastnes.s. The finished cloth shall show colorfastness to dry cleaning ah wet and dry crocking equal t

22、o or better than the standard sample. I.Jiien no standard sample is available, the finished cloth shall show good fast- Because o directional effects, the standard and ,neas ta dry cleaning and wet and dry crocking when tested as specified in Tble IV. 3.7 Fiber identificationl Each rol1 shall be lab

23、eled, ticketed, or in- voiced for fiber content in accordance with the Rules and Regulations Under the Textile Fiber Products Identification Act. 3.8 ?orkmansh Original no load thickness - Thickness under 10 Ibs pressure * 5. PACKAGING * 5.1 Put-up requirements. These requirements shall be in accord

24、ance with Level A (3.2.1) of specification PPP-P-1133, except that the fabric shall be put-up on a suitable reel in which the layers of fabric shall be separated from the next succeeding layer to prevent crushing of the pile. * 5.2 Packaging requirements. The fabric shall be packaged on a suitable r

25、eel in which the layers of the fabric shall be separated frcm the next Succeeding layer to prevent crushing of the pile. * 5.3 Packing. Packing shall be Level A, B, or Commercial as specified (see 6.2). The reel in 5.1 shall be suspended in the container so that it will in no position exert pressure

26、 on any layer of the cloth. * 5.3.1 Levels A, B, or Commercial. The cloth shall be packed in accordance with the applicable requirements of PPP-P-1133. 5.4 Marking. Interior packages and exterior shipping containers shall be marked in accordance with PPP-P-1133. When bar codes are specified in the a

27、cquisition document they shall be applied in accordance with MIL-STD-129. The nomenclature shall be as follows: Cloth, pile (synthetic mouton, knitted) *Type *Length *Width Specification MIL-C-6590C(USAF) “Applicable data to be entered by the supplier. * 5.5 Palletization. When specified (see 6.2) f

28、abric packed as specified in 5.3, shall be palletized in accordance with load type I of MIL-STD-147. Each prepared load shall be bonded with primary and secondary straps in accordance with the bonding means K and L. the appendix of MIL-STD-147. reversing the pattern of each course. does not conform

29、to any of the patterns specified in MIL-STD-147, the pallet pattern used shall first be approved by the contracting officer. Pallet patterns shall be in accordance with Interlocking of loads shall be effected by If the container is of a size which 6. NOTES 6.1 Intended use. The cloth covered by this

30、 specification is intended for use in the manufacturing of clothing items. * 6.2 Ordering data. Acquisition documents should specify the following: 7 Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-MIL-C-6SSOC 3 9999306 OLi25i142 b W MI L-C-6590C( US

31、AF) a, Title, Numbar, and date of this specification. be Type required, C. Length of roll and quantfty des!red, d. Width of Cloth. e. Point of inspection. f. Selection of applicable levels of packaging and packing (5.1 and 5.2). g. Percent of short lengths and reduction from contract price as specif

32、ied. h. When palletiration is required (see 5.5)* 6.3 Standard sample. For access to standard sample, address the procuring 6.4 Local barber supply agencies may be sources for the clipper described. activity issuing the invitation for bids or request for proposal, The prime source is John Oster Manu

33、facturing Company, 5055 N. Lyde11 Street, Hilwaukee Wisconsin 53217 . * 6.5 Changes from previous issue, The margins of this specification are marked with asterisks to indicate where changes (additions, modifications, corrections, deletions) from the previous issue were made. This was done as a conv

34、enience only and the, Government assumes no liability whatsoever for any inaccuracies in these notations. Bidders and contractors are cautioned to evaluate the requirements of this document based on the entire content irrespective of the marginal notations and relationship to the last previous issue

35、. Custodian : Ar Force - 99 Navy - AS Review activities: DLA - CT Preparing Activity : Air Force - 82 (Project No 8305-F868) Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-* TABLE I. Construction. Type I 6 or 7 24?2 oz/sq yd 12 20 85.0 112 21 / 16 1

36、1.0 60 * Type II 2522 OZ/S yd 6 12 20 85.0 1/2?1/16 11.0 60 Characteristic Pile denier Weight, oz/sq yd, min Wales, per inch min Courses, per inch, min Bursting strength, lbs, min Pile, height, inch Pile, recovery % After 1 minute, min After 4 hours recovery, min Sample size in rolls (or containers)

37、 Lot size in yards up to 1200 i/ 3 1201 to 3200 5 3201 to 10,000 7 10,001 to 35,000 10 35,001 to up 15 Acceptance O O O 1 2 TABLE II. List of defects (napped side). Characteristic Material identification Backing compound Material identification Denier Bare spots or thin places (pile missing) Cut, ho

38、le or tear Any mends Spot, stain or streak clearly visible Broken or missing yarn resulting in insufficient or inadequately Embedded crease clearly visible Dropped stitch or run secured nap Requirement Reference 3.2. 3.3 Table I (type) Table I TABLE III. Sample size. TABLE IV. Component test. 9 Prov

39、ided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-MIL-C-b59OC 83 W 9999906 0425194 T MIJP C- 6 5 9 OC ( USAF) TABLE V. E Characteristic Weight, total - l/ Pile Wales per inch Coureee per inch Dursting strength Pile height Pile recovery Blocking - 2/ Flexib

40、ility - 3/ Colorfastness to: Dry cleaning 4J CsoekinL- Rqmt para Table I 3.2.2 Table I Table I Table Table I Table I 3.4.1 3.42 3.6.2 3.62 hod of testing. Test Method 5041 5041 and 4,312 5070 5070 5120 4.3.3 4.3.4 5872 5874 5620 5650 No. det. /sample 5 -5 3 Results re- ported as To the nearesi ounce

41、 per square yard To the nearest sxteenth inct To the nearest z 1/ Exeepc that the specimen size shall be not less than 4 inchessquare. 21 Two 4 x 4-inch samples shall be used for the test and placed back to bock only. for a period of 4 heurs. The samples shall be exposed EO a temperature of 170 22 F

42、 - 3/ Except: that: a, Paragraphs 3.2., 4.4, 4.5, 4.6.1, and 5.3 of method 5874 for hydrostatic resistance shall not: apply. Paragraph 4.1, method 5874* shall be changed to read -40 k3.6 F for 4 hours. b. e. Paragraphs 4.2, method 5874, delete sentences 7 and 8 and substi- tute: “The cloth ehall be

43、folded pile side out, in both the warp and filling directiona“. 4/ In addition to the colorfastness test, the backing compaund shallremain flexible and shall show no tackiness, cracking, or flaking (see 3.2.3). The test for colorfastness and blocking shall be run concurrently. Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-