AIR FORCE MIL-C-83856 (5)-1986 COMPUTER ATTACK TYPE CPU-73 A P《CPU-73 A P型进攻电脑》.pdf

1、15 September 1986 SUPERSEDING Beneficial comments (recommendations, additions, deletions) and any pertinent data which may be of use in improving this document should be addressed to: -City Air Logistics Center/MMEDO, Tinker AFB“0K 73145-5990 by using the self-addressed Standardization Document: Imp

2、rovement Proposal (DD Form 1426) appearing at the end of this document or by letter. Oklahoma - AMENDMENT 4 30 APRIL 1980 MILITARY SPECIFICATION COMPUTER, ATTACK TYPE CPU-73 A/P This amendment forms a part of MIL-C-83856(USAF), dated 2 MAY 1969, and is approved for use within the Department of the A

3、ir Force and is available for use by all Departments and Agencies of the Department of Defense. PAGE 1 * Delete “2.1“ and add: “2.1 Government documents .I * Add: “2.1.1 Specifications, standards, and handbooks. The following specifications, standards, and handbooks form a part of this specification

4、 to the extent specified herein. Unless otherwise specified, the issues of these documents shall be those listed in the issue of the Department of Defense Index of Specifications and Standards (DODISS) and supplement thereto, cited in the solicitation,“ * Under SPECIFICATIONS, Federal, add: “PPP-B-6

5、01 Boxes, Wood, Cleated Plywood“ and “PPP-B-636 Box, Shipping, Fiberboard“. * Under STANDARDS, Military, delete “MIL-STD-831“; “MS63033“ and substitute: “MIL-E-20652/1 Eyelet, Metallic, Rolled Flange Type, and Eyelet Washer“. Add boxed paragraph at bottom center of page. * Add: “2.2 Other publicatio

6、ns. specification to the extent specified herein. Unless otherwise specified, the issues of the documents which are DOD adopted shall be those listed in the issue of the DODISS specified in the solicitation. issues of documents not listed in the DODISS shall be the issues of the nongovernment docume

7、nts which is current oc the date of the solicitation. The following document(s) form a part of this Unless otherwise specified, the ASTM D3951 Packaging, Commercial (Application for copies should be addressed to: PA 19103.) ASTM, 1916 Race St, Philadelphia AMSC N/A FSC 6605 1 of 5 DISTRIBUTION STATE

8、MENT A. Approved for public release; distribution is unlimited. Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,- NIL-C-83856 (5) bb = 77777Ob 0442470 O = o J MIL-C-83856(USAF) AMENDMENT 5 (Nongovernment standards and other publications are normally a

9、vailable from the organizations which prepare or which distribute the documents. These documents also may be available in or through libraries or other informational services.)“ 3.3.1 Delete and substitute: “3.3.1 Discs. accordance with the Composition B, Type II, Class 3 of L-P-535. The material sh

10、all be flat, homogenous, and resistant to water and warpage. discs shall be .O40 inch thick. The center disc shall be .O60 inch thick.“ The computer discs shall be constructed of vinyl chloride in The front and rear * Add: “3.3.1.1 Recovered materials. Recovered materials shall be used to the maximu

11、m extent possible without jeopardizing the end use of the item.“ 3.3.2 Line 2 delete “MS63033“ and add: “MIL-E-20652/1“. PAGE 3 3.3.5 Delete and substitute the following: “3.3.5 Operational manual. One copy of the current operational manual, technical order 5N5-14-14-1, shall be packed in the pocket

12、 of the case (reference paragraph 3.3.4). The contractor must request the government to supply current printed copies for backup. 3.4.2.1 Line 7, change “like“ to “line“. PAGE 4 3.4.2.3 Last line, change “Grade C“ to “Class 3“. PAGE 38 3.4.3.1.3.4 In line 3 change “0.0005“ to “0.005“. In line 7 chan

13、ge “clockwise“ to “counterclockwise“. PAGE 62 * Add: “4.1.1 Responsibility for compliance. sections 3 and 5. The inspection set forth in this specification shall become a part of the contractors overall inspection system or quality program. absence of any inspection requirements in the specification

14、 shall not relieve the contractor of the responsibility of assuring that all products or supplies submitted to the Government for acceptance comply with all requirements of the contract. Sampling in quality conformance does not authorize submission of known defective material, either indicated or ac

15、tual, nor does it commit the Government to acceptance of defective material.“ All items must meet all requirements of The PAGE 64 4.4.3 Delete and substitute the following: “4.4.3 First article tests. 4.5.1 and all of the functional accuracy tests specified in 4.4.4.1 through 4.4.4.8 . “ The first a

16、rticle test shall consist of.tests of 2 Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-MIL-C-83856(USAF) AMENDMENT 5 * Delete “4.4.2, a, b, c. PAGE 66 TABLE XXXI, first column, last line: Change “75.00“ to “70.00“. PAGE 67 TABLE XXXIV: Change TARGET

17、 TAS INDICATION for PRESSURE ALTITUDES of 15 and 30 as shown. TARGET TAS INDICATION PRESSURE ALTITUDE MINIMUM 15 30 13.29 18.32 MAXIMUM 13.33 18.38 PAGE 68 4.4.4.3.4 Line 1: Change -15 to +15O. PAGE 70 Delete existing Table XXXVI and add: amendment . New Table XXXVI shown as page 4 of this PAGE 71 A

18、dd the following new paragraph: - 4.4.4.8 factors table on the front disc shall be visually inspected to verify that this DT + factors table data inspection. The data contained within the DT + data is in accordance with Table XXVIII. PAGE 73 TABLE XXXVII, first column, first line change: “O on Press

19、ure“ to read “0 on Pressure Altitude Scale Center Disc“. PAGE 76 * Delete Section 5 in its entirety and add: “5 PACKAGING 5.1 Preservation-packaging. Preservation-packaging shall be level A, C, or Industrial, as specified (see 6,2). 5.1.1 Level A. 5.1.1.1 Cleaning. Computer shall be cleaned in accor

20、dance with process C-1 of MIL-P-116. 3 Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-w MIL-C-83B56 (5) bb 77777Ob 0442472 4 1 MIL-C-83856(USAF) AMENDMENT 5 J 5.1.1.2 Drying. MIL-P-116. Computer shall be dried in accordance with process D-4 of 5.1.1

21、.3 Preservation application. Not applicable. 5.1.1.4 Unit packaging. Unless otherwise specified by the contracting activity, each computer shall be packaged in quantity unit packs of one each in accordance with Method 1C1 of MIL-P-116. Overbox completed pack in PPP-B-636 container. TABLE XXXVI LEAD

22、DISTANCE WINDOW LEAD DISTANCE SCALE ACCURACY TEST Lead Distance Scale I Graduation Mark 90 HCA Single Turn 22 33 44 55 66 90 HCA D.T.F. 10 25 40 55 70 90 HCA FINAL LEAD-40 Turn 110 HCA Single Turn 22 34 46 58 70 18 26 35 43 52 110 HCA D.T.F. 10 25 40 55 70 18 I 26 110 HCA FINAL LEAD-30 Turn 35 1 43

23、Targer TAS Indication Minimum Maximum 1.2290 1.232 1.369 1.372 1 545 1.555 1.813 1.818 2.276 2.284 .O16150 .O 162 50 .O06690 .O067 10 .O04160 .O04 17 3 .O02846 .O02854 .O01947 . O0 1953 .2560 .2568 .2709 .2717 .2910 .2918 .3220 .3230 .3855 .3865 .904 .906 1.028 1.030 1.220 1.224 1.482 1.486 2.025 2.

24、035 ,012450 .O12350 .O04990 .O05030 .O03036 .O03046 .O02014 .o02020 . O0 13 14 . 001318 .1706 .17 14 .1880 .1888 .2146 .2154 .2510 .2518 . 3266 .3276 4 Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-MIL-C-83856(USkP) AMENDMENT 5 Apply sufficient cus

25、hioning material between bag and unit container of a type, density, and thickness to insure shock transmission does not exceed peak values in Gs established for the computer when completed packs are subjected to the rough handling drop tests of MIL-P-116. 5.1.2 Level C. Each computer shall be clean,

26、 dry, and individually packaged in a manner that will afford adequate protection against corrosion, deterioration, and physical damage during shipment from supply source to the first receiving activity . 5.1.3 Industrial. The Industrial preservation of computer shall be in accordance With ASTM D3951

27、. 5.2 Packing. Packing shall be level A, B, C, or Industrial as specified (see 6.2). 5.2.1 Level A. shipping containers conforming to PPP-B-601, Styles A or B, Class overseas, unless otherwise specified by the contracting activity. shipping container shall be of uniform shape size, minimum tare and

28、cube consistant with the protection required. Computer packaged as specified in 51.1 shall be packed ia Insofar as practical, exterior 5.2.2 Level B. shipping containers conforming to PPP-B-636, class weather-resistant, unless otherwise specified by the contracting activity. Other requirements as sp

29、ecified in 5.2.1 apply. Computer packaged as specified in 5.1.1 shall be packed in 5.2.3 Level C. domestic shipment from the supply source to the first receiving activity for immediate use. regulations. Packing shall be applied which affords adequate protection during This level shall conform to app

30、licable carrier rules and 5.2.4 Industrial. D395 1. The packaged computer shall be packed in accordance with ASTM 5.3 Marking. (see 6.2), interior and exterior containers shall be marked in accordance with MIL-STD-129. “ In addition to any other markings required by the contract or order The margins

31、 of this amendment are marked with an asterisk to indicate where changes (addtions, modifications, corrections, deletions) from the previous amendment were made. assumes no liability whatsoever for any inaccuracies in these notations. Bidders and contractors are cautioned to evaluate the requirement

32、s of this document based on the entire content irrespective of the marginal notations and relationship to the last previous amendment. This was done as a convenience only and the Government Custodian: AIR FORCE - 99 Preparing Activity: AIR FORCE - 71 Project Number : 6605 - F358 *V.S. GOVERNMENT PRINTING OFFICE: 198 - 606-036/44922 5 Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-