AIR FORCE MIL-DTL-83197 B-1996 LINER ANTI-EXPOSURE FLYING COVERALLS CWU-23 P《CWU-23 P飞行反曝光工作服衬垫》.pdf

1、MIL-DTL-83197B W 999990b 20LY233 OOT MIGDTL83197B 12 February 1996 SUPERSEDING MILG83197A(USAF) 6 December 1968 DETAIL SPECIFICATION LINER, ANTI-EXPOSURE, FLYING COVERALLS CWU-23/P 1. SCOPE 1.1 Scope. This specification establishes the requirements for one type of CWU-23P anti-exposure flying covera

2、lls liner. I .2 Classification. The liner shall be rnished in the following sizes, as specified (see 6.2): Size 1 (32-36) Size 2 (32-36) Size 3 (32-36) Size 4 (37-40) Size 5 (37-40) Size 6 (37-40) Size 7 (41-44) Size 8 (4 1-44) Size 9 (4 1-44) Size 10 (45-47) Size 11 (45-47) Size 12 (45-47) 2. APPLI

3、CABLE DOCUMENTS 2.1 General. The documents listed in this section are specified in sections 3 and 4 of this specification. This section does not include documents cited in other sections of this specification or recommended for additional information or as examples. While every effort has been made

4、to ensure the completeness of this list, document users are cautioned that they must meet all specified requirements documents cited in sections 3 and 4 of this specification, weather or not they are listed. 2.2 Government documents. 2.2.1 Specifications. standards. and handbooks. The following spec

5、ifications, standards, and handbooks form a part of this document to the extent specified herein. Unless otherwise specified, the issues of these documents are those listed in the issue of the Department of Defense Index of Specifications and Standards (DoDISS) and supplement thereto, cited in the s

6、olicitation (see 6.2). Beneficial comments (recommendations, additions, deletions) and any pertinent data which may be of use in improving this document should be addressed to: San Antonio AFMClILDD, 306 Tinker Drive BLDG 207, Kelly AFB, TX 7824 1-5916 by using the self-addressed Standardization Doc

7、ument Improvement Proposal (DD Form 1426) appearing at the end of this document or by letter. AMSC NIA FSC 8475 DISTRIBUTION STATEMENT A. Approved for public release; distribution is unlimited. Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-SPECIFIC

8、ATIONS FEDERAL V-F- 106 V-T-295 DDD-B- 1 199 DDD-L-20 MILITARY MIL-C-18387 MIL-C-8 1393 STANDARDS FEDERAL FED-STD- 19 1 FED-STD-60 1 FED-STD-75 1 - Fastener, Slide, Interlocking - Thread, Nylon - Binding Textile, Cotton, Bias-Cut - Label: for Clothing, Equipage, and Tentase, (General Use) - Cloth, T

9、will, Cotton, Fire Retardant Treated Cloth, Knitted, Polyamide, High Temperature Resistant, Simplex, Jersey - Textile Test Methods - Rubber: Sampling and Testing - Stitches, Seams, and Stitchings (Unless otherwise indicated, copies of the above specifications, standards, and handbooks are available

10、from the Standardization Documents Order Desk, 700 Robbins Avenue, Building 4D. Philadelphia, PA 19 1 1 1-5094.) 2.2.2 Other Government documents. drawings, and publications. The following other Government documents, drawings, and publications form a part of this document to the extent specified her

11、ein. Unless otherwise specified, the issues are those cited in the solicitation. DRAWINGS AIR FORCE 68J240-Patterns, Liner, Anti-Exposure, Flying Coveralls CWU-23P, Size I 685241-Patterns, Liner, Anti-Exposure, Flying Coveralls CWU-23P, Size 2 68J242-Pattems, Liner, Anti-Exposure, Flying Coveralls C

12、WU-23P. Size 3 68J243-Pattems, Liner, Anti-Exposure, Flying Coveralls CWU-23/P, Size 4 68J244-Patterns, Liner, Anti-Exposure, Flying Coveralls CW-23/P, Size 5 68J245-Patterns, Liner, Anti-Exposure, Flying Coveralls CWU-23/P, Size 6 68J246-Pattems, Liner, Anti-Exposure, Flying Coveralls CWU-23/P, Siz

13、e 7 68J247-Patterns, Liner, Anti-Exposure, Flying Coveralls CWU-23fP. Size 8 68J248-Pattems, Liner, Anti-Exposure, Flying Coveralls CW-23/P, Size 9 68J249-Pattems, Liner, Anti-Exposure, Flying Coveralls CWU-23/P, Size 1 O 68J250-Patterns, Liner, Anti-Exposure, Flying Coveralls CWU-23/P, Size 1 1 68J

14、25 1-Patterns, Liner, Anti-Exposure, Flying Coveralls CWU-23P, Size 12 (Application for copies of the above listed drawings should be addressed to: San Antonio AFMCnILDD, 306 Tinker Drive BLDG 207, Kelly AFB TX 78241 -59 16.) 2 Provided by IHSNot for ResaleNo reproduction or networking permitted wit

15、hout license from IHS-,-,-MIL-DTL-83 197B 2.3 Non-Government publications. The following documents form a part of this document to the extent specified herein. Unless otherwise specified, the issues of the documents which are DoD adopted are those listed in the issue of the DoDISS cited in the solic

16、itation. Unless otherwise specified, the issues of documents not listed in the DoDISS are those of the documents cited in the solicitation (see 6.2). AMERICAN SOCIETY FOR QUALITY CONTROL (ASQC) ANSYASQC 21.4 - Sampling Procedures and Tables for Inspection by Attributes (Application for copies should

17、 be addressed to American Society for Quality Control, 61 1 East Wisconsin Avenue, Milwaukee WI 53202-4606). 2.4 Order of precedence. In the event of conflict between the text of this document and the references cited herein, The text of this document takes precedence. Nothing in this document, howe

18、ver, supersedes applicable laws and regulations unless a specific exemption has been obtained. 3. REQUIREMENTS 3.1 Preproduction. When required (see 4.2 and 6.2), this specification makes provisions for preproduction testing. 3.2 Materials and components. Materials and components that are not covere

19、d by specifications and drawings or are not specifically described herein shall be of the best quality, as lightweight as practicable, and entirely suitable for the purpose intended. 3.2.1 Outer shell. The fabric for the outer shell of the liner shall be rache1 knit polypropylene netting conforming

20、to Style 8846 (manufactured by the Fablock Mills, Incorporated, 140 Spring Street, Murray Hill, New Jersey), or equal. The color shall be natural or white. 3.2.2 Interlining. The fabric for the interlining of the liner shall conform to MIL-C-18387 and shaii be sage green, USAF color shade No. 1509 (

21、see 6.5). 3.2.3 Wrist stretch inserts. The fabric for the wrist inserts shall conform to MIL-C-81393 and shall be sage green, USAF color shade No. 1509 (see 6.5). 3.2.4 Binding tape. The tape for binding the sleeve ends, leg ends, and neck opening shall be either 1-3/8 inches or 1-1/4 inches wide an

22、d shall conform to type II, class 2 of DDD-B-1199. The color of the binding tape shall be sage green, USAF color shade No. 1509 (see 6.5). 3.2.5 Thread. The thread for assembling the liner and overedging shall conform to type I, class A, letter size B of V-T-295. The color of the thread shall be sag

23、e green, USAF color shade No 1509 (see 6.5). The thread shall have good colorfastness to laundering. 3.2.6 Slide fastener. The slide fastener for the front closure shall conform to type I, size LM or M, style 15, open top stop, bridge bottom stop, two sliders (mouth to mouth), brass chain, and with

24、short tab pulls of V-F-106. The tapes shall be cotton and shall be USAF color shade No. 1509 (see 6.5). The length of the slide fastener for each Size liner shall be determined 6om the patterns for each size liner. The bottom stop of the slide fastener, when installed in the liner, shall be 3/4 inch

25、 (plus or minus 1/8 inch) from the crotch seam, and the top stop shall be not more than 112 inch (plus or minus 1/8 inch) from the finished edge of the neck opening. 3 Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-MIL-DTL-3 I978 3.3 Design. The lin

26、er shall be a one piece garment fabricated from two plies of different fabrics, single-row stitched together at the edges and equipped with stretch inserts at the wrists The liner shall have a slide-fastener closure, at the front, extending from the crotch to the neckline. 3.4 Construction. The line

27、r shall be constructed in accordance with table II using stitched seams The manufacturer is not required to follow the exact sequence of operations as listed in table i 3.4.1 Stitches. seams. and stitching. The stitches, seams, and stitchings specified in table II shall be in accordance with FED-STD

28、-75 1. Stitches per inch shall be as specified in table I Each row of seain stitching shall be straight and parallel to the seam. Unless otherwise specified, a tolerance of plus or ininus 1/32 inch will be allowed in the nomina distance of stitches from the edge on the joining seams of the liner The

29、 thread tension shall be adjusted and maintained so that there shall be no loose stitching and the thread lock is imbedded in the center of the materials being sewn together. Thread breaks, skips, and runoffs shall be overstitched not less than 1/2 inch The ends of stitchings not caught in other sea

30、ms or stitchings shall be backstitched not less than 1/2 inch 3.5 Patterns. The liner shall conform to the patterns referenced on Drawing 68J240, 083242, 685242, 685243, 685244,685245,68J246,685247,683248,685249,68J250, or 68J25 I, as applicable The patterns furnished shall be used as a guide for pr

31、ocessing the manufacturers working patterns. The patterns shall not be altered without prior approval of the procuring activity 3.6 Identification of product. The liner shall have an identification label conforming to type I, classes 1 and 2 of DDD-L-20. The size of the label shall be approximately

32、1-314 by 2-3/4 inches The label shall have good colorfastness to laundering. The label shall contain the following information. Liner, Anti-Exposure, Flying Co.veralls CWU-23/P Pan or Identifying Number (PIN) J/ (see 6 3) Size No. J/ (see 1.2) Stock No. i/ Manufacturers Name i/ Contract No. I/ Date

33、of Manufacture 11 MIL-DTL-83 197B - I! The manufacture shall insert the applicable information. 3.7 Workmanship. The liners shall be uniform in quality and shall be free from irregularities or any defects that could adversely affect the performance, reliability, or durability of the liners. 4. VERIF

34、ICATION 4.1 Classification of insuection. The inspection requirements specified herein are classified as follows: a. Preproduction inspection b. Quality conformance inspection 4.2 Preproduction insiiection. The preproduction inspection shall consist of the visual examinations as specified in 4.3.2.1

35、 and tested as specified in 4.4. 4 I Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,- MIL-DTL-B3L%7B m 9999909 2alJ4237 755 m MIL-DTL-83 1978 4.2.1 Preproduction samples. The preproduction samples shall consist of three liners, each of a different si

36、ze, and shall be representative of the construction, workmanship, components, and materials to be used during production. Before production is commenced, the samples shall be submitted to the procuring activity for examination as specified in 4.3.2.1 to determine that the liners meet the requirement

37、s of this specification. When a contractor is in continuous production of items covered by this specification from contract to contract or within a 12-month period, submission of preproduction samples on the new contract may be waived at the discretion of the procuring activity (see 6.2). Approval o

38、f the preproduction samples or waiver of the preproduction samples shall not preclude the requirements for quality conformance inspection. 4.3 Oualitv conformance inspection. Unless otherwise specified, sampling for inspection shall be performed in accordance with ANSUASQC 21.4. 4.3.1 ComDonents and

39、 materials. Unless otherwise specified herein or in the applicable acquisition documents (see 6.2), components and materials shall be tested in accordance with all requirements of referenced specifications, drawings, and standards of this specification. 4.3.2 Examination of the end item. The end ite

40、m shall be visually examined for defects as specified in 4.3.2.1. The sample unit for the examination shall be one liner. The inspection level for the visual examination shall be II of ANSUASQC 21.4, and the acceptable quality level (AQL) shall be as specified in the contract or purchase order. 4.3.

41、2.1 Visual examination. The liners shall be visually examined for defects as specified in table II. 5. PACKAGING 5.1 Packagine. For acquisition purposes, the packacing requirements shall be as specified in the contract or order (see 6.2). When actual packaging of materiel is to be performed by DoD p

42、ersonnel, these personnel need to contact the responsible packaging activity to ascertain packaging requirements. Packaging requirements are maintained by the Inventory Control Points packaging activity within the Military Department or Defense Agency, or within the Military Department System Comman

43、d. Packaging data retrieval is available from the managing Military Department or Defense Agencys automated packaging files, CD-ROM products, or by contacting the responsible packaging activity. 6. NOTES (This section contains information of a general or explanatory nature which may be helpful, but

44、is not mandatory.) 6.1 Intended use. The liner covered by this specification is intended for continuous wear by aircrew members during overwater flights and is to be worn under the Coveralls, Flying, Anti-exposure CWU-21P and in conjunction with the Underwear, Double-knitted, Anti-exposure CWU-22P a

45、nd the Socks, Rubber SRC-25P. 6.2 Acauisition requirements. Acquisition documents must specie the following a. b. C. d. e. f Title, number, and date of the specification. Issue of DoDISS to be cited in the solicitation, and if required, the specific issue of individual documents referenced (see 2.2.

46、1, 2.2.2, and 2.3). Part or Identifiing Number (PIN) (see 6.3). Waiver of preproduction samples if applicable (see 3.1 and 4.2. i). Requirements for testing components and materials (see 4.3. i). Packaging requirements (see 5.1). 5 - Provided by IHSNot for ResaleNo reproduction or networking permitt

47、ed without license from IHS-,-,- MIL-DTL-83197B W 9799906 2014238 691 W MIL-DTL-83 197B 6.3 Pari or Identifiinp Number (PIN) The PIN format is as follows Sample PIN - M83 197/5 Construction of the PIN l SLASH BASIC NUMBER I 6.4 Subject term (key word) IistinS Aircrew Protective garment Fowl weather

48、Under garment Harsh environment 6.5 Color samples Color samples may be obtained froin the procuring activity or as directed by the contraction officer. 6.6 Fimire. Figure 4 shows general design of the liner and is furnished as information only. 6.7 Changes from Drevious issue. Marginal notations are

49、 not used in this revision to identifi changes with respect to the previous issue due to the extent of the changes. TABLE I. Sewing operations - No. 1 - 2 - Description of Operation _ The liner shall be fabricated from the interlining cotton fabric specified in 3.2.2 and the polypropylene netting specified in 3.2.1. The cotton fabric be used as a carrier for the netting. The combined netting and cotton shall be used for the body and the sleeves or the liner. The cotton