AIR FORCE MIL-S-27447 A-1976 SURVIVAL KIT PARACHUTE PACK SRU-16 P《SRU-16 P型降落伞包生存资料袋》.pdf

1、MIL-S-27447A( USAF) 17 FEB 1976 SUPERSEDING MIL-S-27447 (USAF) 4 April 1961 MILITARY SPECIFICATION SURVIVAL KIT, PARACHUTE PACK SRU-lG/P This specification is approved for use by all Depart- ments and Agencies of the Department of! Defense. 1. SCOPE 1.1 2. APPLICABLE DOCUMENTS This specification cov

2、ers one type of survival kit, designated SRU-l6/P, * 2.1 The following documents of the issue in effect on date of invitation for bids or request for proposal form a part of the specification to the extent specified herein. SPECIFICATIONS Federal V-T-276 V-T-285 EE-M-101 FF-N-180 PPP-B- 5 6 6 PPP-B-

3、636 PPP-T-60 Military MIL-P- MIL-A-148 MIL- C- 5 57 MIL-E-5272 MIL-C-6235 MIL-S-13175 STANDARDS Federal FED-STD-751 Thread, Cotton Thread, Polyester Match, Safety: And Match, Nonsafety (Strike - Anywhere) Needles , Except Surgical , Hand Boxes, Folding, Paperboard Boxes, Shipping, Fiberboard Tape: P

4、ackaging, Waterproof Preservation-Packaging , Methods Of r Aluminum Foil Cloth, Wind Resistant Sateen, Cotton Environmental Testing, Aeronautical And Associated Equipment, General Specification For Compass , Magnetic, Unmounted, Pocket , Survival Starter, Fire, NP3, M2 Stitches , Seams , And Stitchi

5、ngs Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-MIL-S-27qq7A Y2 W 9997906 0233276 5 I MIL-S-S7b47A(USAF) MIL-STD-129 MIL-STD-130 MIL-STD-831 MIL-STD-1458 Marking For Shipment And Storage Identification Marking Of US Military Property Test Reports

6、, Preparation Of Radioactive Materials : Harking Atid Labeling Of Items, Packages And Shipping Containers For Identification In Use, Storage And Transportation DRAWING Air Force 44A8838 Tab - Fire Starting Kit (Copies of specifications, standards, drawings, and publications required by suppliers in

7、connection with specific procureEent functions should be obtained from the procuring activity or as directed by the contracting officer.) it 2.2 Other wblications. The following documente form a part of this specifi- cation to the extent specified herein. Unless otherwise indicated, the issue in eff

8、ect on date of invitation for bids or request for proposal shall apply. Packing and Handling of Dangerow Materials for Transportation by Military Aircraft (Copies may be obtained from the procuring activity or as directed by the contracting officer. ) NATIOIIAL MOTOR FREIGHT TRAFFIC ASSOCIATION , IN

9、C e , AGENT Nat ional Mot or Freight Clae si f i cat ion (Application for copies should be addressed to the American Trucking Associa- tion, Inc., Tariff Order Section. 1616 P Street, N.W., Washington DC 20036.) UNIFORI4 CLASSIFICATION COMMITTEE AGENT Uniform Freight Clas si Picat ion (Application f

10、or copies should be addressed to the Uniform Classification Coamiittee, Room 1106, 222 South Riverside Plaza, Chicago IL 60606.) 3 REQUIREMENTS 3.1 Prenroduction. This specification makes provisions for preproduction testing, 3.2 Components. specified in Table I, The complete survival kit shall cons

11、ist of the items 2 Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-VIEW BEFORE TURNING STITCH AFTER INSERTING INNER CONTAINER STITCH TYPE 501, PER FED-S

12、TO-751 VIEW AFTER TURNING SECTION AIA DIMENSIONS IN INCHES SRUbIG/P SURVIVAL KIT CONTAINER JRE I OUTEF FIG 4 Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS

13、-,-,-MIL-S-27447A(USAF) 3.2.13 Instructions and contents sheet. The instruction and contents sheet shall be provided in the inner container. parchment paper* The sheet shall be made with One side of the sheet shall contain the following information. CONTEXTS Mat Che s Fire Starters Striker Strip Kni

14、fe Needles (10) Steel Wire (20 ft) Compass (1) Fish Hooks (3) (4) (2 1 (1) Water Bag (1) (2) The other side of the shee shall contain the following: INSTRUCTIONS 1. 2. Gave the parachute and cords. The matches must be ignited by striking along the striker strips. The fire starting pads can be ignite

15、d by striking along the striker strips or they can be lit with a match. 3. 4. The matches are not water resistant. Keep them dry. 5. Thread for needles can be obtained from inner cord of parachute suspension line. 3.3 Preparation for assembly. The contents of the survival kit shall be prepared for a

16、ssembly as described in 3.3.1 through 3.3.4. 3.3.1 Fish hooks. The fish hooks, needles and wire shall be attached to a base in the inner container in such a manner as to render them incapable of harming any other components, yet neatly accessible. 3.3.2 Matches. in aluminum foil conforming to MIL-A-

17、148 with a thickness of ,005 inch I.OOO5 inches. ends of the package. of the foil covers ail portions of the five matches. Five matches and one striker strip shall be packed together The heads of adjoining matches shall be placed at opposite Each package shall Be wrapped so that two thicknesses 3.3.

18、3 Needles. The two needles shall be placed along the sides of the knife blades in such a manner that the points and heads do not protrude beyond the ends of the knife. A strip of tape confodng to PPP-T-60, type 3, class 2, shall be placed around each end of the knife in such a manner that the points

19、 and heads are covered and secured to the knife by the strip of tape. 3.3.4 Fire startinR nade. foil conforming to MIL-A-148 with a thickness of 0.0015 inches, plus or minus 0.0005 inch. cover ell portions ofthe pad. strip of tape conforming to PPP-T-60, type 3, class E. The pads shall be wrapped se

20、parately in aluminum Each pad shall be wrapped so that two thicknesses of the foil Each pad shall be sealed with an encircling 6 Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-MIL-S-27447A( USAF ) * 3.4 Assembly. The components listed in Table I sha

21、ll be assembled in the inner container in a manner permitting insertion of the completely assembled container into the outer container. the folded blades toward the center of the package. placed with the face of the compass towards the center of the package. to inserting the inner container in the o

22、uter container, the outer container shall be turned so the seams are on the inside. container, the flaps of the outer container shall be secured with a single row or stitch type 301 (see Figure i) approximately 6 stitches per inch to effect a secure closure but not exceed the pull test requirement (

23、see 3.5.4). thread shall conform to type 1, class 1, size B of V-T-285. The knife shall be placed on a side with Prior The compass shall be After inserting the inner The 3.5 Performance. * 3.5.1 Dimensional check - assembly, The completely assembled kit shall conform to the dimensiona1.requirements

24、specified on Figure 1, except in an area where the thickness may expand to a maximum of 3/4 inch. * 3.5.2 Altitue. There shall be no leakage of the kit upon submersion in water, after subjection to an altitude of 50,000 feet, when tested as specified in 4.4.3. * 3.5.3 Humidity. There shall be no lea

25、kage of the kit after subjection to the humidity test specified in 4.4.4. 3.5.4 Pull test - tabs. The pull tabs shall separate, permitting removal of the inner container, when a maximum pull of 40 pounds is applied, * 3.6 Weight. The weight of the completely assembled kit shall not exceed 3.3 ounces

26、. * 3.7 Identification of product. The inner and outer container shall be durable and legibly marked using waterproof ink with the words “SURVIVAL KIT“ in letters not less than 1/4 inch high and “PARACHUTE PACK SRU-lG/P“ and “4240-00-741-9713Ls“ the date of manufacture in letters not less thaii 1/8

27、inch high. The letters shall be centered on the survival kit and shall be oriented along the length of the kit. The outside of one flap shall be marked with the words “PULL TO OPEN“ in letters not less than 1/8 inch in height. 3.8 Workmanship. workmanlike manner. The finished survival kit shall be c

28、lean and free from any defect that might affect appearance, uniformity, or functionability. 4. QUALITY ASSURANCE PROVISIONS The information shall be in accordance with MIL-STD-130. The survival kits shall be constructed in a thoroughly * 4.1 Responsibility for inspection. Unless otherwise specified

29、in the contract or purchase order, the supplier is responsible for the performance of all inspection requirements as specified herein. Except as otherwise specified in the contract or order, the supplier may use his own or any other facilities suitable for the performance of the inspection requireme

30、nts specified herein, UnleSS disapproved by the Government. The Government reserves the right to perform any of the inspections set forth in the specification where such inspections axe deemed necessary to assure supplies and services conform to prescribed requirements. Provided by IHSNot for Resale

31、No reproduction or networking permitted without license from IHS-,-,-MIL-S-27447A 42 9999906 0233282 O W MfGS-2(447A( USAF) * 4.2 Classification of tests. The inspection and testing of survival kits shall be classified as follows: a. Quality conformance inspection See 4.3 b. Preproduction testing Se

32、e 4.5 4,3 guality conformance inspection. Quality conformance inspection shall consist of: a. Individual tests b. ampling plan and tests * 4.3.1 Individual tests. Each survival kit shall be subjected to the following tests : a. Examination of product See 4.4.1 b. Dimensional check-assembly See 4.4.2

33、 4.3.2 SamDlinR plan and tests. * 4.3.2.1 J. accordance with MIL-STD-129. Components assembled and sealed in the outer container as Packing shall be level A, B, or C as specified (see 6.2). Closing and Kits preserved and packaged as specified in 5.1 shall be Containers shall be of minimum weight Pac

34、king for level B shall be the same as specified in 5.2.1, Kits shall be packed in a manner which will insure arrival at Containers and packing shall comply with Uniform Freight Interior and exterior shipping containers shall be marked in 5.3.1 Additional markinq. or contract, the unit, Intermediate,

35、 and exterior shipping container shall be marked in accordance with MIL-STD-129, MIL-STD-1458, and paragraph 11-57 of Air Force Manual 71-4, as applicable to the mode(s) of transportation. 6. NEES 6.1 Intended user for use by personnel under emergency survival conditions. 6.2 Orelering data. Procure

36、ment documents should specie the following: In addition to any other markings required by order Survival kits covered by this specification are intended a, Title, number, and date of this specification. b. C. Preproduction requirements. (See 3.1) 6.3 The margins of this specification are marked with

37、 an asterisk to indicate where changes (additions, modifications, corrections, deletions previous issue were made. This was done as a convenience only and the Govern- ment assumes no liability whatsoever for any inaccuracies in these notations, Bidders and contractors are cautioned to evaluate the r

38、equirements of this docunent based on the entire content irrespective of the marginal notations and relationship to the last previous issue. Level of packaging and packing desired. (See 5.1 and 5.2) from the Custodian : Revew Activity: Air Force - 82 Air Force - 11 Preparing Activity: Project No. 4240-F653 Air Force - 82 (FCM-84) *US. GOVERNMENT PRINTING OFFICE: 1076-603-766/8177 1 10 m .- Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-