AIR FORCE MIL-STD-1766 B-1994 NUCLEAR HARDNESS AND SURVIVABILITY PROGRAM REQUIREMENTS FOR ICBM WEAPON SYSTEMS《洲际弹道导弹武器系统的核硬度和生存能力计划要求》.pdf

1、II NOT MEASUREMENT SENSITIVE il MIL-STD-17666 (USAF) O9 SEPT 1994 Superseding O1 DECEMBER 1986 DOD-STD-1766A MILITARY STANDARD NUCLEAR HARDNESS AND SURVIVABILITY PROGRAM REQUIREMENTS FOR ICBM WEAPON SYSTEMS AMSC F3998 AREA ENVR DISTRIBUTION STATEMENT A: Approved for Public Release: Distribution is U

2、nlimited. Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-t 1. This military standard is approved for use by all Departments and Agencies of the Department of Defense. 2, Beneficial comments (recommendations, additions, deletions) and any pertinent d

3、ata that may be of use in improving this document should be addressed to: Space and Missile Systems Center, AFMC SMC/SDFC, 160 Skynet Street, Suite 231 51 Los Angeles AFB, CA 90245.4683, by using the self- addressed Standardization Document Improvement Proposal (DD Form 1426) appearing at the end of

4、 this document, or by letter. 3. This revision of MIL-STD-1766 contains a significant expansion and a complete reorganization of the 1 December 1986 version. It includes much new and revised text, as well as the incorporation of lessons learned during the application of MIL-STD-1766A to intercontine

5、ntal ballistic missile (ICBM) procurements. The key features of the revision are summarized below. 4 SAMSO STD 77-6 ( System Requirements Analysis Program for the MX Weapon System) is an essential companion document to MIL-STD-17668. 5. The scope and content of the document has been expanded in the

6、following ways: a All phases of the system life cycle are included and a more complete and balanced treatment of each phase is given. In contrast, MIL-STD-1766A focused primarily on the engineering and manufacturing development (EMD) phase and did not address the operations and support phase. b. Nuc

7、lear hardness and survivability (NH ( 2 ) guidance to SPO personnel on the generation of NH and ( 3 ) guidance on hardness critical item (HCI) identification and documentation. h. The data item descriptions (DIDs) referenced in MIL-STD-I766A, except for the test plan and test report DIDs, have been

8、revised or rewritten to reflect both lessons learned and the expanded scope and content of this revision. 6. A complete reorganization of the text has been implemented that provides greater clarity and insight into the various program elements and tasks that constitute a comprehensive NH b. treatmen

9、t of system elements in addition to CIS; c. clarification of life cycle hardness (LCH) requirements; and d. modification of contractor data requirements to enhance program efficiency and cost-effectiveness over the system life cycle; among these are: ( 1 ) a new requirement for an HCI list drawing;

10、this requirement is detailed in appendix C; ( 2 ) a new requirement for a system hardness analysis report (SHAR) to document the results of the system level hardness evaluation activity; ( 3 ) a new requirement for an NH and ( 4 ) the integration of the existing DlDs for the hardness assurance plan

11、(DI-ENVR-80263), hardness maintenance plan (DI- ENVR-80264), and hardness surveillance plan (DI-ENVR- 80265) with the DID for the NH the title of the hardness maintenance plan has been changed to “hardness maintenance preparation support plan“ to more precisely identify the documents program purpose

12、. 8 Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-. . MIL-STD-17bbB 94999L1 0478723 T23 I- MIL-STD-17668 (USAF) PARAGRAPH 1 . ScOpE 1 1 . 1 Purpose 1 1 . 2 Application . 1 1.2.1 Tailoring . 1 2 . APPLICABLE DOCUMENTS . 2 2.1 Government documents .

13、2 2.2 Order of precedence 2 3 . DEFINITIONS . 3 3.1 Definittons 3 4 . GENERAL REQUIREMENTS . 4 4.1 NH b. the particular system life cycle phase(+ under contract; and c. the particular categories of hardware utilized. Table 5-1 identifies the NH 5 Provided by IHSNot for ResaleNo reproduction or netwo

14、rking permitted without license from IHS-,-,-MIL-STD-1766B m 9999911 0478732 T36 m MIL-STD-17668 (USAF) I . . . . . . . . . . . . . . . . 5) . . . . . . . . . . . . ._L . . . . . . . . . . . . . . . +:.: X :.:.:. . . . . . . . . . . . iY “ ,. ?: “ . 1.1.1-1 iii O c E c (D O v- - E E 2 n U 3 r 2 3 L

15、n - - 3 I - * :i_ i , . I. . I ,.i I . ,.v , ,/ ,.“ , . , . -: ,. /v . ;:.: . . . . . “. . . “_ . “ i al U D L en - r 4 r! r) I I . a . - 3 al E L F3 .- a 3 22 z e v) E m v) 2 E W- O c, E W - O Q) El O c, 5 CT er v) 3 L c, O V c, c f! s I . a a - v) E O c, m V O m .- - - _ *._._. * . : . . i 4 - + (

16、r C ; .- - - 9 e C (I: (I: c C c c Lu E $i 3 E W- 4- c a P al O al - n c c 4 x I - ._ . “. 6 Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-“ . ,: .“. .“. ;X.! .:.:.:.: i ,i?a . i . 10 - E O o % e al v) al v) E r (CI Lu e I . . . . O - c O o c m 3 V

17、 - H c Io E u e I . . . . . (I - c O (CI o .c .- CI .- 5 v) v) al E m c al al e - - E E en ? s 2 I 7 Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-.:.:.:.; ., _, ., _. . ( _l .x+ .x.:.: . ._. _. _. _. . . ., ._ _. . _. . . , _, ._. ., ,. :.:. “ :.-

18、 L ., (3 . . . . . . . . . . . . . : . A: i.*. :.;. : , , . “. . io :c j *g B; U ej Q) mi= =;a DIU W. 51 pis/ a: ; a. I !. . . . a . a - , . . “,. - il i .: il :I il il : .- I . . . a . a - cn 5 F 5 ji C( D =! I “.) ; . . ). - :. I . a . . a - c O .- W E n h 5 E (D Q) 03 c U +.r O E gi n n v) 3 II/

19、Z! I . . . . a I c O CI (D Q .- E E n a E3 E 5 8 n n v) 3 3; Zi I . . . . . O - E O .- W i? e! n a Y E g; m m. O CI n CI 3 v)! ni z; I . ( . . .“(. - ., a . a c O .- CI E n e! D F CI O (D n E g n 3 n v) z ,. . . a I c O .- CI E m m a3 a L 5 s a E ? D c, O n P v) 3 I/) z ? 2; ejj a Provided by IHSNot

20、 for ResaleNo reproduction or networking permitted without license from IHS-,-,-MIL-STD-L?bbB 999991L 0478735 745 MIL-STD-17668 (USAF) 9- O cq4 22 (ION) SW311 lVlN3Wd013NONON E o Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-MIL-STD-17666 (USAF) MI

21、L-STD-17bbB 99999L1 01)7873b b8L q h x s Z 9- O cqaj 22 s z s z aa 10 Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-MIL-STD-17668 (USAF) b. technical and economic objectives are sound, needed, reasonable, and well defined; c. major uncertainties ar

22、e identified for further investigation during the demonstration and validation phase; and d. preliminary cost and schedule estimates are based upon sound analyses. 5.1 .I .2 Svstem support/intearation (SS b. develop concept designs to the extent that configuration item (Cl) selection can be evaluate

23、d in terms of hardness allocation strategies and hardness interface requirements with other AVE/SE contractors; and c. Formally present the results of these tasks at a system design review (SDR). 5.1.2.3 SS and b. system level test planning and conduct to support development of a concept design and

24、weapon system requirements; and 11 Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-MIL-STD-37bbB m 9999933 0478738 454 m MIL-STD-1766B (USAF) c. the inclusion of hardness requirements in the facilities design criteria in a manner that is compatible w

25、ith all other facility/hardware interfacing requirements. 5.1.2.4 Facilities architectural and enaineerina (A develop concept designs to the extent that configuration item (Cl) selection can be evaluated in terms of hardness allocation strategies and hardness interface requirements with other AVE/SE

26、 contractors; develop the AVE/SE hardness requirements; accomplish the design, evaluation, verification, and qualification of CIS that satisfy these hardness requirements; accomplish the planning, preparation, and implementation of activities required in support of life cycle hardness; support to th

27、e system level hardness evaluation activity; and support to the SPOs system level assessment activity. The contractor shall also support the development of facility and assembly and checkout (A b. support the SPOs system level assessment activity; c. develop facility and RPlE hardness requirements f

28、or incorporation in the facilities design criteria; and d. accomplish the correct incorporation of these facility and RPlE hardness Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-“ _ _ MIL-STD-L7bbB a 9999933 0478739 390 . “ MIL-STD-1766B (USAF) req

29、uirements in the facility design drawings. 5.1.3.4 Facilities A and b. the SPOs system level assessment activity. Any design changes implemented during the production and deployment phase that may affect system level hardness shall undergo appropriate system level hardness evaluation update to verif

30、y hardness adequacy. Any system level changes that have an LCH impact shall be fully included in LCH activities and documentation, as appropriate. 5.1.4.4 Facilities A and b. results in a deployed weapon system that satisfies all specified hardness requirements. 13 Provided by IHSNot for ResaleNo re

31、production or networking permitted without license from IHS-,-,-5.1.6 Operation and support phase. 5.1.6.1 Supportina command. The supporting command will: a implement a hardness maintenance program and a periodic hardness surveillance program throughout the weapon systems operational life; and b. p

32、erform system level assessments when requested by the operating command. 5.1.6.2 Hardness .surveillance support - contractor. The contractor shall perform the applicable 5.3 tasks necessary to support the hardness surveillance program implemented by the supporting command. 5.1.6.3 Operatina command.

33、 The operating command will update or initiate system level assessments as required. 5.2 Hardware cateaory NH under these circumstances, the design elements in the host system that provide the required protection shall be identified as hardness critical items (HCls), and the performance requirements

34、 associated with the modification shall be included in the applicable PIDS. b. the selection of alternative commercial items that meet the allocated hardness requirements without modification; or c. some combination of a. and b. such that the commercial item under consideration does not require modi

35、fication. If no modification is necessary, the requirements of 5.2.1.1.2.1 shall apply. If modification is necessary, the requirements of 5.2.1.1.2.2 shall apply. In all cases of the use of non developmental commercial items, whether unmodified or modified, the contractor shall be responsible for th

36、e full and satisfactory implementation of all applicable NH and b. appropriate, cost-effective test and inspection procedures that will ensure that future procurements of the item will exhibit at least the same level of hardness as the item evaluated. 5.2.1.1.2.2 Modified commercial NDI. If the hard

37、ware item under consideration is modified to meet its allocated hardness requirements, the contractor shall, based on the nature and extent of the modification under consideration, provide recommendations to the SPO, for SPO decision, as to whether: a the item should be treated fully as a developmen

38、tal item, per 5.2.1.1.1; or b. only those portions of the items design that are planned to undergo modification should be treated under the requirements of 5.2.1.1 .l, while the unmodified portions of the design are treated in accordance with the requirements of 5.2.1.1.2.1. The recommendations conc

39、erning this matter prepared by the contractor shall take LCH considerations fully into account, in addition to other relevant program concerns. 5.2.1.1.3 ND1 items/militarv. The contractor shall evaluate early in the preliminary design and hardness allocation activities whether any already existing

40、military item intended for use in the design of a CI will meet all applicable hardness requirements. If 15 Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-MIL-STD-17bbB = 9999911 0478742 985 MIL-STD-1766B (USAF) some modification to meet hardness req

41、uirements is found to be necessary, the contractor shall first consider: a. the utilization or alteration of design features of the host system to reduce military items hardness requirements to the extent that no modification is necessary; under these circumstances, the design elements in the host s

42、ystem that provide the required protection shall be identified as HCls, and the performance requirements associated with the modification shall be included in the applicable PIDS. b. the selection of alternative non developmental military items that meet the allocated hardness requirements without m

43、odification; or c. some combination of a. and b.- such that -the- non developmental military item under consideration does not require modification. If no modification is necessary, the requirements of 5.2.1.1.3.1 shall apply. If modification is necessary, even after careful consideration of the opt

44、ions identified above, and the proposed modification is permitted by interchangeability requirements, the requirements of 5.2.1.1.3.2 shall apply. In all cases of the use of non developmental military items, whether unmodified or modified, the contractor shall be responsible for the full and satisfa

45、ctory implementation of all applicable NH and b. it will be procured directly from the supplier that had originally designed it, or an approved second source, to the original specifications and drawings and the same manufacturing procedures. 5.2.1.1.3.2 Modified military NDI. If the hardware item un

46、der consideration is modified to meet its allocated hardness requirements, the contractor shall, based on the nature and extent of the modification under consideration, provide recommendations to the SPO, for SPO decision, as to whether: a the item should be treated fully as a developmental item, pe

47、r 5.2.1.1.1; or b. only those portions of the items design that are planned to undergo modification should be treated under the requirements of 5.2.1.1.1 , while the unmodified portions of the design are treated in accordance with the requirements of 5.2.1.1.3.1. The recommendations concerning this

48、matter prepared by the contractor shall take LCH considerations fully into account, in addition to other relevant program concerns. Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-5.2.1.2 Government furnished equipment (GFE). 5.2.1.2.1 GFE hardness requirements. The contractor shall use the hardness capability of the GFE (as previously established by requirements or test) to allocate hardness requirements to the WSE(s) under contract in the host system. If the resulting hardness allocations are imprac