API STD 609-2016 Butterfly Valves Double-flanged Lug- and Wafer-type (EIGHTH EDITION ERTA April 13 2017).pdf

1、Butterfly Valves: Double-flanged, Lug-and Wafer-typeAPI STANDARD 609 EIGHTH EDITION, FEBRUARY 2016API MONOGRAM PROGRAM EFFECTIVE DATE: AUGUST 1, 2016Special NotesAPI publications necessarily address problems of a general nature. With respect to particular circumstances, local, state, and federal law

2、s and regulations should be reviewed.Neither API nor any of APIs employees, subcontractors, consultants, committees, or other assignees make any warranty or representation, either express or implied, with respect to the accuracy, completeness, or usefulness of the information contained herein, or as

3、sume any liability or responsibility for any use, or the results of such use, of any information or process disclosed in this publication. Neither API nor any of APIs employees, subcontractors, consultants, or other assignees represent that use of this publication would not infringe upon privately o

4、wned rights.API publications may be used by anyone desiring to do so. Every effort has been made by the Institute to assure the accuracy and reliability of the data contained in them; however, the Institute makes no representation, warranty, or guarantee in connection with this publication and hereb

5、y expressly disclaims any liability or responsibility for loss or damage resulting from its use or for the violation of any authorities having jurisdiction with which this publication may conflict.API publications are published to facilitate the broad availability of proven, sound engineering and op

6、erating practices. These publications are not intended to obviate the need for applying sound engineering judgment regarding when and where these publications should be utilized. The formulation and publication of API publications is not intended in any way to inhibit anyone from using any other pra

7、ctices.Any manufacturer marking equipment or materials in conformance with the marking requirements of an API standard is solely responsible for complying with all the applicable requirements of that standard. API does not represent, warrant, or guarantee that such products do in fact conform to the

8、 applicable API standard.Users of this Standard should not rely exclusively on the information contained in this document. Sound business, scientific, engineering, and safety judgment should be used in employing the information contained herein.All rights reserved. No part of this work may be reprod

9、uced, translated, stored in a retrieval system, or transmitted by any means, electronic, mechanical, photocopying, recording, or otherwise, without prior written permission from the publisher. Contact the Publisher, API Publishing Services, 1220 L Street, NW, Washington, DC 20005.Copyright 2015 Amer

10、ican Petroleum InstituteForewordThis standard is a purchase specification for butterfly valves designed for installation between flanges specified in ASME B16.1, ASME B16.5, ASME B16.24, and ASME B16.42, Classes 125-600; MSS SP-44, Class 150; and ASME B16.47, Series A (was MSS SP-44 except for certa

11、in materials) or Series B (was API 605), Class 150 for the NPS sizes defined herein.This standard requires the purchaser to specify certain details and features. Although it is recognized that the purchaser may desire to modify, delete, or amplify sections of this standard, it is strongly recommende

12、d that such modifications, deletions, and amplifications be made by supplementing this standard, rather than by rewriting or incorporating sections thereof into another complete standard.API standards are published as an aid to procurement of standardized equipment and materials. These standards are

13、 not intended to inhibit purchasers or producers from purchasing or producing products made to specifications other than those of API. Nothing contained in any API publication is to be construed as granting any right, by implication or otherwise, for the manufacture, sale, or use of any method, appa

14、ratus, or product covered by letters patent. Neither should anything contained in the publication be construed as insuring anyone against liability for infringement of letters patent.Shall: As used in a standard, “shall” denotes a minimum requirement in order to conform to the specification.Should:

15、As used in a standard, “should” denotes a recommendation or that which is advised but not required in order to conform to the specification. This document was produced under API standardization procedures that ensure appropriate notification and participation in the developmental process and is desi

16、gnated as an API standard. Questions concerning the interpretation of the content of this publication or comments and questions concerning the procedures under which this publication was developed should be directed in writing to the Director of Standards, American Petroleum Institute, 1220 L Street

17、, NW, Washington, DC 20005. Requests for permission to reproduce or translate all or any part of the material published herein should also be addressed to the director.Generally, API standards are reviewed and revised, reaffirmed, or withdrawn at least every five years. A one-time extension of up to

18、 two years may be added to this review cycle. Status of the publication can be ascertained from the API Standards Department, telephone (202) 682-8000. A catalog of API publications and materials is published annually by API, 1220 L Street, NW, Washington, DC 20005.Suggested revisions are invited an

19、d should be submitted to the Standards Department, API, 1220 L Street, NW, Washington, DC 20005, standardsapi.org.iiiContentsPage1 Scope . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .

20、 12 Normative References . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 13 Terms and Definitions. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .

21、 . . . . . . . . . . . 24 Pressure-temperature Ratings. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 24.1 Valve Rating . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .

22、. . . . . . . . . . . . . . . . . . . . . . . . . 24.2 Shell Rating . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 34.3 Seat Rating. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .

23、. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 34.4 Differential Pressure Rating . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 35 Design. . . . . . . . . . . . . . . . . .

24、 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 45.1 General . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .

25、. . 45.2 Body . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 45.3 Face-to-face Dimensions . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .

26、 . . . . . . . . . . . . . . . . . . . . 55.4 Disc Clearance . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 75.5 Shaft and Shaft Seals . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .

27、. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 85.6 Piping Connection External Bolt Holes . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 85.7 Valve Body Seat RetainerCategory B Valves Only . . . . . . . . . . . .

28、 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 85.8 Operating Mechanisms. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 95.9 Electrical Continuity . . . . . . . . . . . . . . . . . . . . . . . . .

29、 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 105.10 Packing Gland BoltingCategory B Valves Only . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 106 Materials . . . . . . . . . . . . . . . . . . . . . . . . . . . .

30、. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 116.1 Body . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 116.2 Process Wetted Pa

31、rts . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 116.3 Packing or Shaft Seal Materials. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 116

32、.4 Gland Bolting . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 116.5 Operating MechanismsCategory B Valves Only . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .

33、. . 117 Examination, Inspection and Testing . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 117.1 Examination Requirements. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .

34、. . . . . 117.2 Inspection by the Purchaser . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 117.3 Production Pressure Tests. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .

35、 . . . . . . . . . . . . . 117.4 De-rated Valve Type Testing. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 117.5 Electrical Continuity Valve Type Testing . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .

36、 . . . . . . . . . . . . . . . . . . 127.6 Repair of Defects . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 128 Markings . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .

37、. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 129 Packaging and Shipping. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 139.1 Coatings . . . . . . . . . . . . . . . . . . . . . . . . . .

38、 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 139.2 Shaft Packing. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 139.3 Packaging. . . . .

39、 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 139.4 Spare Parts. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .

40、. . . . . . . . . 1310 Purchase Order Information. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 14vPageAnnex A (informative) Use of API Monogram by Licensees . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .

41、 . . . . . . . . 15Annex B (informative) Information to be Specified by Purchaser . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 18Annex C (informative) Typical Butterfly Valve Construction and Nomenclature . . . . . . . . . . . . . . . . . . . . . . . 20Annex D (normative)

42、Disc-to-pipe Clearances . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 24Bibliography . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .

43、 . 28Figures1 External Bolting Options for Lug- and Wafer-type Valves . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 92 Limitations for Flange Face Interruptions that Fall Within the Gasket Seating Area(NPS 6 through NPS 48) 10C.1 Typical Concentric-type . . . . . . .

44、. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 20C.2 Typical Single Offset-type Construction (Category B) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 21C.3 Typical Double Offset-type Construc

45、tion (Category B) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 22C.4 Typical Triple Offset-type Construction (Category B) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 23D.1 Typical Concentric-type Construction (Category A) . . .

46、 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 25D.2 Typical Eccentric-type Construction (Category B) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 26Tables1 Minimum Seat Pressure-temperature Ratings for Category B Valves with

47、 PTFE or RPTFE Seats . . . . . 32 Face-to-face Dimensions for Category A Valves (Lug- and Wafer-type) . . . . . . . . . . . . . . . . . . . . . . . . . . . 53A Face-to-face Dimensions for Category B Valves, (Lug- and Wafer-type) . . . . . . . . . . . . . . . . . . . . . . . . . . 63B Face-to-face Di

48、mensions for Category B Valves, (Double-flanged Long Pattern) . . . . . . . . . . . . . . . . . . . 63C Face-to-face Dimensions for Category B Valves, (Double-flanged Short Pattern) . . . . . . . . . . . . . . . . . . . 7D.1 Nominal Radial Clearances . . . . . . . . . . . . . . . . . . . . . . . . .

49、 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 25D.2 Relationship of Unlined Steel Pipe Schedule to Valve Category, Size, and ASME Class . . . . . . . . . . . . 27vi1Butterfly Valves: Double-flanged, Lug-and Wafer-type1 Scope1.1 This standard covers design, materials, face-to-face dimensions, pressure-temperature ratings, and examination, inspection and test requirements for gray iron, ductile iron, bronze, steel, nickel-based alloy, or special alloy butterfly valves. 1.2 If product is supplied bearing the API Monogram and manufactured at a facility licens