API TR 1PER15K-1-2013 Protocol for Verification and Validation of High-pressure High-temperature Equipment (First Edition)《高温高压设备的检验和确认协定.第1版》.pdf

1、Protocol for Verification and Validation of High-pressure High-temperature EquipmentAPI TECHNICAL REPORT 1PER15K-1FIRST EDITION, MARCH 2013Special NotesAPI publications necessarily address problems of a general nature. With respect to particular circumstances, local,state, and federal laws and regul

2、ations should be reviewed.Neither API nor any of APIs employees, subcontractors, consultants, committees, or other assignees make anywarranty or representation, either express or implied, with respect to the accuracy, completeness, or usefulness of theinformation contained herein, or assume any liab

3、ility or responsibility for any use, or the results of such use, of anyinformation or process disclosed in this publication. Neither API nor any of APIs employees, subcontractors,consultants, or other assignees represent that use of this publication would not infringe upon privately owned rights.API

4、 publications may be used by anyone desiring to do so. Every effort has been made by the Institute to assure theaccuracy and reliability of the data contained in them; however, the Institute makes no representation, warranty, orguarantee in connection with this publication and hereby expressly discl

5、aims any liability or responsibility for loss ordamage resulting from its use or for the violation of any authorities having jurisdiction with which this publication mayconflict.API publications are published to facilitate the broad availability of proven, sound engineering and operatingpractices. T

6、hese publications are not intended to obviate the need for applying sound engineering judgmentregarding when and where these publications should be utilized. The formulation and publication of API publicationsis not intended in any way to inhibit anyone from using any other practices.Any manufacture

7、r marking equipment or materials in conformance with the marking requirements of an API standardis solely responsible for complying with all the applicable requirements of that standard. API does not represent,warrant, or guarantee that such products do in fact conform to the applicable API standard

8、.Users of this Technical Report should not rely exclusively on the information contained in this document. Sound busi-ness, scientific, engineering, and safety judgment should be used in employing the information contained herein.All rights reserved. No part of this work may be reproduced, translate

9、d, stored in a retrieval system, or transmitted by any means, electronic, mechanical, photocopying, recording, or otherwise, without prior written permission from the publisher. Contact the Publisher, API Publishing Services, 1220 L Street, NW, Washington, DC 20005.Copyright 2013 American Petroleum

10、InstituteForewordNothing contained in any API publication is to be construed as granting any right, by implication or otherwise, for themanufacture, sale, or use of any method, apparatus, or product covered by letters patent. Neither should anythingcontained in the publication be construed as insuri

11、ng anyone against liability for infringement of letters patent.This document was produced under API standardization procedures that ensure appropriate notification andparticipation in the developmental process and is designated as an API standard. Questions concerning theinterpretation of the conten

12、t of this publication or comments and questions concerning the procedures under whichthis publication was developed should be directed in writing to the Director of Standards, American PetroleumInstitute, 1220 L Street, NW, Washington, DC 20005. Requests for permission to reproduce or translate all

13、or any partof the material published herein should also be addressed to the director.Generally, API standards are reviewed and revised, reaffirmed, or withdrawn at least every five years. A one-timeextension of up to two years may be added to this review cycle. Status of the publication can be ascer

14、tained from theAPI Standards Department, telephone (202) 682-8000. A catalog of API publications and materials is publishedannually by API, 1220 L Street, NW, Washington, DC 20005.Standards referenced herein may be replaced by other international or national standards that can be shown to meetor exc

15、eed the requirements of the referenced standard.Suggested revisions are invited and should be submitted to the Standards Department, API, 1220 L Street, NW,Washington, DC 20005, standardsapi.org.iiiContentsPage1 Scope . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .

16、. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 11.1 Purpose. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 11.2 Existing Designs and In-service Equipme

17、nt . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 21.3 Applicability . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 22 Terms and Definitions

18、. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 23 Abbreviations and Symbols. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 63.1 A

19、bbreviations. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 63.2 Symbols . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .

20、 . . . . . . . . . . . . . . . . . . 74 Functional Specification. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 74.1 Responsibility . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .

21、. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 74.2 Environmental Conditions . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 84.3 Specified Loads and Characteristics . . . . . . . . . . . . . . . .

22、 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 84.4 Life Cycle Loading. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 134.5 Applicable Industry Standards and/or Regulatory

23、Requirements. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 135 Technical Specifications. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 165.1 General . . . . . . . . . . . . . . . . . . . . . . . . .

24、. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 165.2 Responsibilities . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 165.3 Personnel Requi

25、rements . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 165.4 Documentation. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .

26、 . . 165.5 Response to Functional Specifications . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 175.6 Fit-for-service Basis . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .

27、 . . . . . . . . . . 195.7 Aftermarket Activities . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 196 Best Practices and Guidance. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .

28、 . . . . . . . . . . . . . . . . . . . . 206.1 Materials . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 206.2 Design Verification . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .

29、 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 396.3 Design Validation Testing. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 456.4 Manufacturing Process Specification (MPS) . . . . .

30、. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 516.5 Aftermarket Activities . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 53Annex A (informative) Material Properties . .

31、 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 54Annex B (informative) Metallurgical-related Failures. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 67Annex C (informative) Failure Modes and

32、 Effects Analysis (FMEA) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 70Annex D (informative) Technical Considerations on the Selection of Castings and Forgings . . . . . . . . . . . . . 81Annex E (informative) Quality Management System Guidelines . . . . . . . . . . . . . .

33、 . . . . . . . . . . . . . . . . . . . . . . . . 82Bibliography . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 84Figures1 System Analysis Specification Breaks (Completion) . . . . . . . .

34、 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 112 System Analysis Specification Breaks (Drilling) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 123 Performance Envelope Example . . . . . . . . . . . . . . . . . . . . . . . . . . .

35、. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 144 Combined Loading Capacity Chart from API 6AF1 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 145 Example of True Stress for 2 1/4Cr-1Mo True Strain Curve. . . . . . . . . . . . . . . . . . .

36、. . . . . . . . . . . . . . . . . . . 336 Validation Process. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 48A.1 Example of Effect of Temperature on Thermophysical Properties of 4130 and 4340 (MMPDS) . . .

37、 . . . . 55vContentsPageA.2 Example of Effect of Temperature on the Tensile Ultimate Strength (Ftu) and Tensile Yield Strength (Fty) of AISI Low-alloy Steels (All Products) (MMPDS) . . . . . . . . . . . . . . . . . . . . . . . . . . . . 56A.3 Example of Compendium of Cyclic Curves for Carbon Steel a

38、nd 2 1/4Cr-1Mo . . . . . . . . . . . . . . . . . . . . . 58A.4 Example of Effect of Temperature on Tensile Properties of Alloy N08535 in 125 ksi Minimum Yield Strength Grade . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 59A.5

39、Example of Effect of Temperature on Strength of Alloy 25CrW (UNS S39274) . . . . . . . . . . . . . . . . . . . . . 60A.6 Example of Effect of Temperature on the Thermophysical Properties on UNS N07718 (MMPDS) . . . . . 62C.1 FMEA Process . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .

40、. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 71C.2 General Validation FMEA Workflow . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 72C.3 Detailed Validation FMEA Workflow . . . . . . . . . . . .

41、 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 72C.4 Modified Choke . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 77Tables1 API References for Equipment. . .

42、. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 32 Material Properties Cited by Design Standards. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 223 Typical Carbon and Low-alloy Steels

43、for HPHT Use (T 350 F or P 15,000 psi) . . . . . . . . . . . . . . . . . . 234 Stainless Steel and Corrosion Resistant Alloys for HPHT Use (T 350 F or P 15,000 psi). . . . . . . . . . 245 List of Typical Materials . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .

44、. . . . . . . . . . . . . . . . . . . . . . . 266 Typical Protocols for Property Determination . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 357 Summary of Test Protocols for Nonmetallic Materials in M-710 . . . . . . . . . . . . . . . . . . . . . .

45、. . . . . . . . . . . 388 Cross References of Industry Standards . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 389 Reference Industry Standards for Design Verification . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .

46、. . . . 4110 Reference Industry Standards for Validation . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 46A.1 Example of Thermal Decay of API 5CT Casing . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 54

47、A.2 Recommended Yield Strength Reduction Ratios in Percent by Temperature for Low-alloy Steels . . . . 55A.3 Example of Composition of 4130M7 Tubing. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 56A.4 Example of Hot Tensile Testing of 4130M7 Tubin

48、g . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 57A.5 Recommended Yield Strength Reduction Ratios in Percent by Temperature for Stainless Steels and CRA Steels . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .

49、. . . . . . . . . . . . . . . . . . 58A.6 Example of Mechanical Properties of Alloy 825 (Cold Worked) from 4 in. Diameter Tube. . . . . . . . . . . . 61A.7 Example of Chemical Composition of Heats Tested . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 63A.8 Example of Tensile Properties as a Function of Temperature for INCONELAlloy 725. . . . . . . . . . . . . . 63A.9 Example of Composition of Alloy Tested in the Accompanying Tensile Data . . . . . . . . . . . . . . . . . . . . . . 66A.10 Example of Tensile Properties of Titanium 6-2-4-6 (UNS R5626