ANSI AAMI 14408-2005 Tracheal tubes designed for laser surgery-Requirements for marking and accompanying information.pdf

1、ANSI/AAMI/ISO 14408: 2005Tracheal tubes designed for laser surgeryRequirements for marking and accompanying informationAmerican National StandardThis document was approved and published when the U.S. TAG for TC 121 was held by ASTM, but it is now an AAMI standard. The original formatting has been ma

2、intained, so there are some variations from the typical AAMI style. Published by Association for the Advancement of Medical Instrumentation 4301 N. Fairfax Drive, Suite 301 Arlington, VA 22203-1633 www.aami.org 2014 by the Association for the Advancement of Medical Instrumentation All Rights Reserve

3、d This publication is subject to copyright claims of ISO, and AAMI. No part of this publication may be reproduced or distributed in any form, including an electronic retrieval system, without the prior written permission of AAMI. All requests pertaining to this document should be submitted to AAMI.

4、It is illegal under federal law (17 U.S.C. 101, et seq.) to make copies of all or any part of this document (whether internally or externally) without the prior written permission of the Association for the Advancement of Medical Instrumentation. Violators risk legal action, including civil and crim

5、inal penalties, and damages of $100,000 per offense. For permission regarding the use of all or any part of this document, complete the reprint request form at www.aami.org or contact AAMI, 4301 N. Fairfax Drive, Suite 301, Arlington, VA 22203-1633. Phone: 703-525-4890; Fax: 703-525-1067. Printed in

6、 the United States of America ISBN 1570205310 Approved as an American National Standard by ASTM International ASTM InternationalINTERNATIONALSTANDARDANSI/ISO14408Second edition2005-06-01Tracheal tubes designed for laser surgery Requirements for marking and accompanying information Tubes trachaux des

7、tins aux oprations laser Exigences relatives au marquage et aux informations daccompagnement ANSI/ISO 14408:2005(E) Approved as an American National Standard with deviations by ASTM International ASTM InternationalThese materials are subject to copyright claims of ASTM International. Not for resale

8、without the prior written permission of ASTM International. No part of this publication may be reproduced in any form, including an electronic retrieval system, without the prior written permission of ASTM International. ii ASTM International ANSI/ISO 14408:2005(E) Approved as an American National S

9、tandard with deviations by ASTM International ASTM International iiiForeword ISO (the International Organization for Standardization) is a worldwide federation of national standards bodies (ISO member bodies). The work of preparing International Standards is normally carried out through ISO technica

10、l committees. Each member body interested in a subject for which a technical committee has been established has the right to be represented on that committee. International organizations, governmental and non-governmental, in liaison with ISO, also take part in the work. ISO collaborates closely wit

11、h the International Electrotechnical Commission (IEC) on all matters of electrotechnical standardization. International Standards are drafted in accordance with the rules given in the ISO/IEC Directives, Part 2. The main task of technical committees is to prepare International Standards. Draft Inter

12、national Standards adopted by the technical committees are circulated to the member bodies for voting. Publication as an International Standard requires approval by at least 75 % of the member bodies casting a vote. Attention is drawn to the possibility that some of the elements of this document may

13、 be the subject of patent rights. ISO shall not be held responsible for identifying any or all such patent rights. ISO 14408 was prepared by Technical Committee ISO/TC 121, Anaesthetic and respiratory equipment,Subcommittee SC 2, Tracheal tubes and other equipment.This second edition cancels and rep

14、laces the first edition (ISO 14408:1998), Clauses 4 and 5 and Figure 1 of which have been technically revised. For the purposes of this International Standard, the CEN annex regarding fulfilment of European Council Directives has been removed. ANSI/ISO 14408:2005(E) Approved as an American National

15、Standard with deviations by ASTM International ivASTM InternationalIntroductionThis International Standard is intended to provide requirements for marking, labelling and information supplied for tracheal tubes which are designed for resistance to ignition by a laser and which have been tested for la

16、ser resistance in accordance with ISO 11990 including a standard format for reporting results obtained when tested in accordance with ISO 11990. It is intended that, by limiting the requirements to disclosure of information determined in accordance with standard test methods, the manufacturer will b

17、e allowed maximum use of alternatives in design and materials. INTERNATIONAL STANDARD ANSI/ISO 14408:2005(E)Approved as an American National Standard with deviations by ASTM International ASTM International 1Tracheal tubes designed for laser surgery Requirements for marking and accompanying informat

18、ion 1 Scope This International Standard specifies marking, labelling and information to be supplied by the manufacturer for cuffed and uncuffed tracheal tubes and related materials designed to resist ignition by a laser. 2 Normative references The following referenced documents are indispensable for

19、 the application of this document. For dated references, only the edition cited applies. For undated references, the latest edition of the referenced document (including any amendments) applies. ISO 11990, Optics and optical instruments Lasers and laser-related equipment Determination of laser resis

20、tance of tracheal tube shafts3 Terms and definitions For the purposes of this document, the following terms and definitions apply. 3.1 tracheal tube tube designed for insertion through the larynx into the trachea to convey gases and vapours to and from the trachea ISO 4135:2001 3.2 cuff inflatable b

21、alloon permanently attached around the tracheal tube near the patient end to provide an effective seal between the tube and the trachea NOTE Adapted from ISO 4135:2001. 3.3 laser-resistant tracheal tube tracheal tube specifically designed by the manufacturer for use during laser surgery of the airwa

22、y NOTE This includes devices sold preassembled or in kit form. 3.4 laser-resistant tracheal tube treatment covering and/or surface treatment that adapts or modifies non-laser-resistant tracheal tubes for use in laser surgery of the airway ANSI/ISO 14408:2005(E) Approved as an American National Stand

23、ard with deviations by ASTM International 2ASTM International3.5 upper anatomical airway upper airway airway above the laryngotracheal junction 3.6 laser-resistant portion that portion of the tracheal tube intended by the manufacturer to be laser-resistant 4 Marking and labelling 4.1 Use of symbols

24、The requirements given in 4.2, 4.3, and 4.4 may be met by the use of the appropriate symbols in accordance with ISO 7000 or EN 980. 4.2 Marking 4.2.1 Marking of tracheal tubes, connectors, packages, inserts and information to be supplied by the manufacturer should comply with EN 1041. 4.2.2 The foll

25、owing shall be permanently marked on or affixed to the tracheal tube or tracheal tube treatment: a) the name and/or trademark of the manufacturer or supplier; b) the nominal inside diameter in millimetres designated by the manufacturer for the tracheal tube; c) model identification, if necessary to

26、distinguish between similar products from the same manufacturer; d) for cuffed tracheal tubes, a reference to any preparation designated by the manufacturer as essential for protection of the cuff from ignition (e.g. “inflate the cuff with saline or water before use”). 4.2.3 Additional marks may be

27、provided (optional) to assist in positioning the tracheal tube within the trachea. 4.2.4 Any component of a laser-resistant tracheal tube treatment that is affixed to, or protects the treatment covering or material until it is applied to the tracheal tube, shall be marked with a reference to any pre

28、paratory steps designated by the manufacturer as essential to the laser resistance of the tube (e.g. “saturate covering with saline solution”). 4.2.5 If the laser-resistant portion is not visually obvious, this shall be marked. 4.2.6 If any marks are applied to the laser-resistant area of the trache

29、al tube, the test to determine laser-resistance values required for the graph in 5.4 shall be carried out directly upon these markings. 4.2.7 All markings shall be of sufficient size and contrast to be legible. 4.2.8 All markings shall be non-toxic and tissue-compatible. Marking materials should res

30、ist deterioration by anaesthetic agents. The markings should be durable and remain legible during use of the tube. If the tracheal tube is intended for reuse, the materials should resist deterioration by the recommended agents and procedures used to clean and disinfect or sterilize the device. ANSI/

31、ISO 14408:2005(E) Approved as an American National Standard with deviations by ASTM International ASTM International 34.3 Labelling of packs The following information shall be on the laser-resistant tracheal tube or laser-resistant tracheal tube treatment pack: a) a description of contents, includin

32、g wording to indicate that the tracheal tube is intended for use in laser surgery; b) the name and/or trademark of the manufacturer or supplier; c) the product code or catalogue number; d) the largest outside diameter after preparations for use; e) the nominal internal diameter in millimetres design

33、ated by the manufacturer for the tracheal tube; f) the means to ensure traceability such as type, batch or serial number or year of manufacturer; g) the word “STERILE” or “NON-STERILE”, as appropriate; h) for tracheal tubes not intended for reuse, the words “SINGLE USE” or equivalent; i) for cuffed

34、tracheal tubes, the cuff resting diameter, expressed in millimetres; j) any storage instructions, including a statement of known conditions of storage likely to result in rapid deterioration of the materials (e.g. high temperature, ultraviolet light or fluorescent lighting); k) the “use by” date exp

35、ressed as (YYYY-MM); l) an instruction to refer to information describing laser resistance, including type(s) and nominal wavelength(s), considered by the manufacturer as appropriate for use and contraindications. 4.4 Labelling of shelf or multi-unit containers The following information shall be on

36、shelf or multi-unit containers: a) the descriptive name of the device (trademark, etc.); b) the name and/or trademark of the manufacturer or supplier; c) the product code or catalogue number; d) the nominal outside diameter of the tube; e) the nominal inside diameter of the tube; f) the batch number

37、; g) the word(s) “STERILE” or “NON-STERILE”, as appropriate; h) for tracheal tubes not intended for reuse, the words “SINGLE USE” or equivalent; i) the “use by” date expressed as (YYYY-MM); j) the quantity of unit packages in the container; k) any storage instructions, including a statement of known

38、 conditions of storage likely to result in rapid deterioration of the materials (e.g. ultraviolet light or fluorescent lighting); ANSI/ISO 14408:2005(E) Approved as an American National Standard with deviations by ASTM International 4ASTM Internationall) an instruction to refer to information descri

39、bing laser resistance, including type(s) and nominal wavelength(s) considered by the manufacturer as appropriate for use and contraindications. 5 Information to be supplied by the manufacturer 5.1 Instructions for preparation and use of laser-resistant tracheal tube and tracheal tube treatments5.1.1

40、 For laser-resistant tracheal tube treatments that require set-up and maintenance steps to achieve the stated laser resistance, explicit information shall be provided, including applicable precautionary statements. 5.1.2 Unless the tracheal tube is intended and marked as being for single use, recomm

41、ended methods of cleaning and disinfection or sterilization shall be provided. 5.2 Indications for use Information on type(s) of laser and nominal wavelength(s) considered by the manufacturer to be appropriate for use with the laser-resistant tracheal tube and information on contraindications shall

42、be provided. 5.3 Warnings and precautions about the use of the tube Descriptions of damage to tubes and effects on tubes that may result from contact with lasers and which could result in harm to the patient or healthcare personnel shall be provided. These warnings shall include a description of eve

43、nts (other than ignition) reported during testing for laser resistance in accordance with ISO 11990. 5.4 Graph showing test results for laser resistance 5.4.1 For each type of laser considered by the manufacturer to be appropriate for use with the tracheal tube as determined in accordance with ISO 1

44、1990, a graphic presentation of the results shall be given. 5.4.2 The graph shall take the form shown in Figure 1 and shall comply with 5.4.2.1 to 5.4.2.6. 5.4.2.1 The title of the graph shall be “Maximum power settings at which ignition did not occur when tested using a spot size of 0,5 mm”. 5.4.2.

45、2 Power shall be plotted on the vertical axis from 0 W to 100 W. Power levels greater than 100 W may be shown if warranted by test results. 5.4.2.3 The duration of laser energy shall be plotted on the horizontal axis from 0 s to 10 s. The length of the horizontal axis shall be (160 r 10) % of the he

46、ight of the vertical axis at 100 W. 5.4.2.4 Data shall be provided for durations of 1 s and 10 s. Additional data shall be included to limit the change from adjacent data points to no more than 20 % of the larger value or 2 W, whichever is greater. No data shall be included for durations less than 1

47、 s or greater than 10 s. 5.4.2.5 Power/duration curves shall be shown using straight lines between data points. Laser types and nominal wavelengths shall be identified for each curve. 5.4.2.6 The following statements shall appear in proximity to the graph, and they shall indicate that the statements

48、 apply to the data presented in the graph: a) a statement that the data obtained apply only to the laser resistant portion of the tracheal tube shaft and that other components of the system, such as the inflation system and cuff, have not been tested; ANSI/ISO 14408:2005(E) Approved as an American N

49、ational Standard with deviations by ASTM International ASTM International 5b) a cautionary statement making clear that the clinical relevance of the tests has not been fully established; c) a cautionary statement that laser resistance under surgical conditions may differ from the values given, due to the presence of water, blood or body fluids. KeyX laser energy duration, s Y power, W 1 Nd:YAG laser (1,06 m) 2 CO2laser (10,6 m) 3 KTP laser (0,532 m) 4 argon laser (0,5 m) Figure