ANSI American Society of Sanitary Engineering 1037-2015 Performance Requirements for Pressurized Flushing Devices for Plumbing Fixtures (First Edition Update No 1 September 2017).pdf

1、Performance Requirements for Pressurized Flushing Devices for Plumbing FixturesASSE 1037-2015/ASME A112.1037-2015/CSA B125.37-15ANSI Approved: January 2015An American National StandardASSE 1037-2015/ASME A112.1037-2015/CSA B125.37-15Performance requirements for pressurized flushing devices for plumb

2、ing fixturesLegal Notice for Harmonized StandardJointly Developed by ASME, ASSE, and CSAIntellectual property rights and ownershipAs between The American Society of Mechanical Engineers (ASME), ASSE International Chapter of IAPMO, nullCnull(nullSSEnull, annullCananullan Stannullrnull Association (CS

3、Anullnull (collectinullly nullnullSME, ASSE, annullCSA) annullthe nullers of this nullcnullent (whether it be in printenullor electronic form), ASME, ASSE, annullCSA are the nullint owners of all wornull containenullherein that are protectenullby copyright, all tranullnullarnull (enullept as otherwi

4、se notenull to the contrary), annull all innullntions annull tranull secrets that may be containenull in this nullcnullent, whether or not snullh innullntions annulltranull secrets are protectenullby patents annullapplications for patentsnullThe nullanullhorinullnullnulle, monullfication, copying, o

5、r nullsclosnulle of this nullcnullent may nullolate laws that protect the intellectnulll property of ASME, ASSE, annullCSA annullmay ginull rise to a right in ASME, ASSE, annullCSA to seenulllegal renulless for snullh nulle, monullfication, copying, or nullsclosnullenullASME, ASSE, annullCSA resernu

6、ll all intellectnulll property rights in this nullcnullentnullDisclaimer and exclusion of liabilityThis nullcnullent is pronullnullnullwithonull any representations, warranties, or connulltions of any nullnnull enullress or implienull inclnulling, withonull limitation, implienullwarranties or connul

7、ltions concerning this nullcnullents fitness for a particnullar pnullpose or nulle, its merchantability, or its nonnullnfringement of any thirnull partys intellectnulll property rightsnull ASME, ASSE, annull CSA null not warrant the accnullacy, completeness, or cnullrency of any of the information p

8、nulllishenullin this nullcnullentnullASME, ASSE, annullCSA manull no representations or warranties regarnullng this nullcnullents compliance with any applicable statnulle, rnulle, or regnullationnullInull null Enullnull Snullnull ASME, ASSE, annull CSA, TnullInull nullSPECTInull nullnullnullEEnull,

9、MEMnullnull, SnullSInullAnullES, Onull AnullInullATEnull COMPAnullES, Onull TnullInull EMPnullnullES, nullnullCTOnull, Onull OnullICEnull, null nullAnullE nullnull Anull nullnullCT, InullInullCT, Onull InullInullnullAnull nullMAnullS, Inullnullnull, nullSS, COSTS, Onull EnullEnullES, nullnullOEnulln

10、ull CAnullEnull Inullnullnullnull nullT nullT nullMITEnull TO SPECIAnull Onull COnullEnullEnullIAnull nullMAnullS, nullST nullnullnullE, nullSInullSS InullEnullnullTIOnull nullST Onull nullMAnullnull nullTA, Onull Anull OTnullnull COMMEnullIAnull Onull ECOnullMIC nullSS, nullETnullnull nullSEnull In

11、ull COnullnullCT, TOnull (Inullnullnullnull nullnullInullnullE), Onull Anull OTnullnullTnullOnull OnullnullAnullnullTnull, AnullSInull Onull OnullOnullnullSnullTInull nullOM ACCESS TO OnullPOSSESSIOnullOnullnullE OnullTnullS nullCnullEnull, EnullnullInullASME OnullCSA nullnull nullEnullAnullISEnullO

12、nullTnull POSSInullnullTnullOnullSnullnullnullMAnullS, Inullnullnull, nullSS, COSTS, OnullEnullEnullESnullIn pnulllishing annullmanullng this nullcnullent anullilable, ASME, ASSE, annullCSA are not nullnullrtanullng to rennullr professional or other sernullces for or on behalf of any person or entit

13、y or to perform any nullty owenullby any person or entity to another person or entitynullThe information in this nullcnullent is nullrectenullto those who hanull the appropriate nullgree of enullerience to nulle annullapply its contents, annullASME, ASSE, annullCSA accept no responsibility whatsoenu

14、llr arising in any way from any annullall nulle of or reliance on the information containenullin this nullcnullentnullASME, ASSE, annullCSA hanull no power, nor null they nullnullrtanull, to enforce compliance with the contents of the stannullrnull or other nullcnullents they nullintly pnulllishnull

15、Authorized use of this documentThis nullcnullent is being pronullnullnull by ASME, ASSE, annull CSA for informational annull nonnullommercial nulle onlynull The nuller of this nullcnullent is anullhorinullnullto null only the followingnullIf this nullcnullent is in electronic formnullnullloanullthis

16、 nullcnullent onto a compnuller for the sole pnullpose of renullewing itnullnullsearch annullbrowse this nullcnullentnullannullnullprint this nullcnullent if it is in Pnull formatnullnullmitenullcopies of this nullcnullent in print or paper form may be nullstribnullenullonly to persons who are anull

17、horinullnullby ASME, ASSE, annull CSA to hanull snullh copies, annullonly if this nullgal nulltice appears on each snullh copynullIn anullition, nullers may not annullmay not permit others tonullalter this nullcnullent in any way or remonull this nullgal nulltice from the attachenullstannullrnullnul

18、lsell this nullcnullent withonull anullhorinulltion from ASME, ASSE, annullCSAnullornullmanull an electronic copy of this nullcnullentnullIf yonullnull not agree with any of the terms annullconnulltions containenullin this nullgal nulltice, yonullmay not loanullor nulle this nullcnullent or manull a

19、ny copies of the contents hereof, annullif yonullnull manull snullh copies, yonullare renullirenullto nullstroy them immenullatelynullnulle of this nullcnullent constitnulles yonull acceptance of the terms annullconnulltions of this nullgal nullticenullStandards Update ServiceASSE 1037-2015/ASME A11

20、2.1037-2015/CSA B125.37-15February 2015Title: Performance requirements for pressurized flushing devices for plumbing fixturesPagination: 23 pages (xii preliminary and 11 text), each dated February 2015To register for e-mail notification about any updates to this publication go to shop.csa.ca click o

21、n CSA Update ServiceThe List ID that you will need to register for updates to this publication is 2422076.If you require assistance, please e-mail techsupportcsagroup.org or call 416-747-2233.nullsit nullnullnull roupnull policy o n prinullacy at csagroup.org/legal to find out how we protect your pe

22、rsonal information.TMA trade-mark of the Canadian Standards Association, operating as “CSA Group”Published in February 2015 by CSA GroupA not-for-profit private sector organization178 Rexdale Blvd., Toronto, Ontario, Canada M9W 1R31-800-463-6727 416-747-4044Visit our Online Store at shop.csa.caASSE

23、1037-2015/ASME A112.1037-2015/CSA B125.37-15Performance requirements for pressurized flushing devices for plumbing fixturesPublished in February 2015 by ASSE International18927 Hickory Creek Drive, Suite 220, Mokena, Illinois 60447(708) 995-3019Visit us online at www.asse-plumbing.orgisit our websto

24、re at ASSE International18927 Hickory Creek Dr, Suite 220Mokena, IL 60448Tel: (708) 995-3019Fax: (708) 479-6139E-mail: general.infoasse-plumbing.org www.asse-plumbing.org ASSE International 2015Commitment for AmendmentsThis Standard is issued jointly by The American Society of Mechanical Engineers (

25、ASME), the ASSE International Chapter of IAPMO, LLC. (ASSE), and CSA Group. Amendments to this Standard will be made only after processing according to the Standards development procedures of ASME, ASSE, and CSA Group.The American Society of Mechanical Engineers (ASME) Two Park AvenueNew York, NY 10

26、016-5990USAwww.asme.orgISBN 978-0-7918-7012-9 2015The 2015 edition of this Standard is being issued with an automatic addenda subscription service. The use of addenda allows revisions made in response to public review comments or committee actions to be published as necessary.Published in February 2

27、015 by CSA GroupA not-for-profit private sector organization178 Rexdale BoulvardToronto, Ontario, CanadaM9W 1R31-800-463-6727 or 416-747-4044Visit the CSA Group Online Store at shop.csa.caISBN 978-1-77139-026-2 CSA Group 2015All rights reserved. No part of this publication may be reproduced in any f

28、orm whatsoever without the prior permission of the publisherFebruary 2015 iiiContents 2015 ASSE International 2015 American Society of Mechanical Engineers 2015 CSA GroupPerformance requirements for pressurizedflushing devices for plumbing fixturesASME A112 Standards Committee on Plumbing Materials

29、and Equipment vCSA Technical Committee on Plumbing Fittings viiASSE Product Standards Committee xASME/ASSE/CSA Harmonization Task Group on Plumbing Fittings xiPreface xiiSection I 11Scope 1Section II 12 Reference publications and definitions 12.1 Reference publications 12.2 Definitions 2Section III

30、33 Design and general requirements 33.1 Pressures 33.2 Temperatures 33.3 Backflow prevention 33.4 Accessible designs 33.5 Control stop 33.6 Connections to water supply and fixtures 33.6.1 Inlet connections 43.6.2 Outlet connections 43.7 Coatings 43.8 PFDs incorporating electrical features 43.8.1 Gen

31、eral 43.8.2 Testing 4Section IV 44 Performance requirements and test methods 44.1 General 44.1.1 Preconditioning 44.1.2 Installation for testing 44.1.3 Test conditions 44.1.4 Order of tests 44.2 Pressure test 44.2.1 Purpose 44.2.2 Procedure 54.2.3 Performance criteria 54.3 Back siphonage test Non-ta

32、nk type PFDs 54.3.1 Purpose 54.3.2 Procedure 5 2015 ASSE International 2015 American Society of Mechanical EngineersASSE 1037-2015/ASME A112.1037-2015/CSA B125.37-15 2015 CSA Groupiv February 20154.3.3 Performance criteria 54.4 Backflow test Tank type PFDs 54.4.1 Purpose 54.4.2 Procedure 54.4.3 Perf

33、ormance criteria 64.5 Hydraulic performance tests 64.5.1 Purpose 64.5.2 Procedure 64.5.3 Performance criteria 64.6 Operating requirements 64.6.1 Purpose 64.6.2 Procedure 74.6.3 Performance criteria 74.7 Life cycle test 74.7.1 Purpose 74.7.2 Procedure 74.7.3 Performance criteria 84.8 Integral control

34、 stop life cycle test 84.8.1 Purpose 84.8.2 Procedure 84.8.3 Performance criteria 84.9 Hydrostatic pressure test for non-tank type PFDs 94.9.1 Purpose 94.9.2 Procedure 94.9.3 Performance criteria 94.10 Hydrostatic pressure test for tank type PFDs 94.10.1 Purpose 94.10.2 Procedure 94.10.3 Performance

35、 criteria 9Section V 95 Markings, packaging, and installation instructions 95.1 Markings 95.2 Water consumption 105.3 Visibility of markings 105.4 Packaging 105.5 Installation instructions 10Tables1 Sequence for hydraulic performance tests 6Figures1 Backflow test set up for tank type PFDs 102 Swing

36、check 113 Poppet type check nozzle type body 114 Poppet type flat or level seat body 11Performance requirements for pressurizedflushing devices for plumbing fixturesFebruary 2015 v 2015 ASSE International 2015 American Society of Mechanical Engineers 2015 CSA GroupASME A112 Standards Committee on Pl

37、umbing Materials and EquipmentD.W. Viola IAPMO,Mokena, Illinois, USAChairS. Rawalpindiwala Kohler Co., Kohler, Wisconsin, USAVice-ChairR.K. Adler City of San Jose, San Jose, California, USAS.F. Aridi NSF International, Ann Arbor, Michigan, USAJ.A. Ballanco JB Engineering however, they should not con

38、tain proprietary names or information.ASME procedures provide for reconsideration of any interpretation when or if additional information that might affect an interpretation is available. Further, persons aggrieved by an interpretation may appeal to the cognizant ASME Committee.Interpretations are p

39、ublished on the ASME Web site under the Committee Pages at http:/cstools.asme.org/ as they are issued.CSA Notes:(1) Use of the singular does not exclude the plural (and vice versa) when the sense allows.(2) Although the intended primary application of this Standard is stated in its Scope, it is impo

40、rtant to note that it remains the responsibility of the users of the Standard to judge its suitability for their particular purpose.xiv February 2015 2015 ASSE International 2015 American Society of Mechanical EngineersASSE 1037-2015/ASME A112.1037-2015/CSA B125.37-15 2015 CSA Group(3) This Standard

41、 was developed by consensus, which is defined by CSA Policy governing standardization Code of good practice for standardization as “substantial agreement. Consensus implies much more than a simple majority, but not necessarily unanimity”. It is consistent with this definition that a member may be in

42、cluded in the Technical Committee list and yet not be in full agreement with all clauses of this Standard.(4) To submit a request for interpretation of this Standard, please send the following information to inquiriescsagroup.org and include “Request for interpretation” in the subject line:(a) defin

43、e the problem, making reference to the specific clause, and, where appropriate, include an illustrative sketch;(b) provide an explanation of circumstances surrounding the actual field condition; and(c) where possible, phrase the request in such a way that a specific “yes” or “no” answer will address

44、 the issue.Committee interpretations are processed in accordance with the CSA Directives and guidelines governing standardization and are available on the Current Standards Activities page at standardsactivities.csa.ca.(5) This Standard is subject to review five years from the date of publication. S

45、uggestions for its improvement will be referred to the appropriate committee. To submit a proposal for change, please send the following information to inquiriescsagroup.org and include “Proposal for change” in the subject line:(a) Standard designation (number);(b) relevant clause, table, and/or fig

46、ure number;(c) wording of the proposed change; and(d) rationale for the change.ASSE Notes:(1) Requests for interpretationRequests for interpretation may be sent to any of the (3) standards organizations. All interpretations are reviewed and agreed upon by the ASSE International, ASME, and CSA prior

47、to response. Requests for interpretations may be sent to:Staff Engineering GroupASSE International18927 Hickory Creek Drive, Suite 220Mokena, IL 60448-8399Requests must include:Name and contact information of the individual requesting the interpretation;Name of organization the individual represents

48、 (if any);Appropriate references to the standards clauses that have a bearing on the issue cited in the request;A concise explanation of the issue requiring a technical interpretation;Any supporting documentation that will assist in understanding or describing the issue;Any recommendations the reque

49、stor would like to make concerning a possible technical interpretation, along with appropriate justification or comments.Forms for requests or general guidance can be obtained by emailing staffengineerasse-plumbing.org.(2) Endorsement vs. ListingASSE International does not endorse any product, but rather lists products that have successfully been applied for and meet the given standard. In exchange the manufacturer is allowed to place the ASSE Seal with the given standard number on their product for public recognitio