ANSI API STD 2000-2014 Venting Atmospheric and Low-pressure Storage Tanks (Seventh Edition).pdf

1、Venting Atmospheric andLow-pressure Storage TanksAPI STANDARD 2000SEVENTH EDITION, MARCH 2014Special NotesAPI publications necessarily address problems of a general nature. With respect to particular circumstances, local, state, and federal laws and regulations should be reviewed.Neither API nor any

2、 of APIs employees, subcontractors, consultants, committees, or other assignees make any warranty or representation, either express or implied, with respect to the accuracy, completeness, or usefulness of the information contained herein, or assume any liability or responsibility for any use, or the

3、 results of such use, of any information or process disclosed in this publication. Neither API nor any of APIs employees, subcontractors, consultants, or other assignees represent that use of this publication would not infringe upon privately owned rights.Users of this standard should not rely exclu

4、sively on the information contained in this document. Sound business, scientific, engineering, and safety judgment should be used in employing the information contained herein. Where applicable, authorities having jurisdiction should be consulted.API publications may be used by anyone desiring to do

5、 so. Every effort has been made by the Institute to assure the accuracy and reliability of the data contained in them; however, the Institute makes no representation, warranty, or guarantee in connection with this publication and hereby expressly disclaims any liability or responsibility for loss or

6、 damage resulting from its use or for the violation of any authorities having jurisdiction with which this publication may conflict.API publications are published to facilitate the broad availability of proven, sound engineering and operating practices. These publications are not intended to obviate

7、 the need for applying sound engineering judgment regarding when and where these publications should be utilized. The formulation and publication of API publications is not intended in any way to inhibit anyone from using any other practices.Any manufacturer marking equipment or materials in conform

8、ance with the marking requirements of an API standard is solely responsible for complying with all the applicable requirements of that standard. API does not represent, warrant, or guarantee that such products do in fact conform to the applicable API standard.All rights reserved. No part of this wor

9、k may be reproduced, translated, stored in a retrieval system, or transmitted by any means, electronic, mechanical, photocopying, recording, or otherwise, without prior written permission from the publisher. Contact the Publisher, API Publishing Services, 1220 L Street, NW, Washington, DC 20005.Copy

10、right 2014 American Petroleum InstituteForewordNothing contained in any API publication is to be construed as granting any right, by implication or otherwise, for the manufacture, sale, or use of any method, apparatus, or product covered by letters patent. Neither should anything contained in the pu

11、blication be construed as insuring anyone against liability for infringement of letters patent.Shall: As used in a standard, “shall” denotes a minimum requirement in order to conform to the specification.Should: As used in a standard, “should” denotes a recommendation or that which is advised but no

12、t required in order to conform to the specification.This document was produced under API standardization procedures that ensure appropriate notification and participation in the developmental process and is designated as an API standard. Questions concerning the interpretation of the content of this

13、 publication or comments and questions concerning the procedures under which this publication was developed should be directed in writing to the Director of Standards, American Petroleum Institute, 1220 L Street, NW, Washington, DC 20005. Requests for permission to reproduce or translate all or any

14、part of the material published herein should also be addressed to the director.Generally, API standards are reviewed and revised, reaffirmed, or withdrawn at least every five years. A one-time extension of up to two years may be added to this review cycle. Status of the publication can be ascertaine

15、d from the API Standards Department, telephone (202) 682-8000. A catalog of API publications and materials is published annually by API, 1220 L Street, NW, Washington, DC 20005.Suggested revisions are invited and should be submitted to the Standards Department, API, 1220 L Street, NW, Washington, DC

16、 20005, standardsapi.org.iiiContentsPage1 Scope . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 12 Terms, Definitions, and Abbreviated Terms . . . . . . . . . . . . . . . . . . . . . .

17、 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 13 Nonrefrigerated Aboveground Tanks . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 33.1 General . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .

18、 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 33.2 Causes of Overpressure or Vacuum . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 43.3 Determination of Venting Requirements. . . . . . . . . . . .

19、 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 73.4 Means of Venting . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 203.5 Considerations for Tanks with Potentially F

20、lammable Atmospheres. . . . . . . . . . . . . . . . . . . . . . . . . . . . . 213.6 Relief-device Specification. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 223.7 Installation of Venting Devices and Open Vents . . . .

21、. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 234 Refrigerated Aboveground and Belowground Tanks . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 244.1 General . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .

22、 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 244.2 Causes of Overpressure or Vacuum . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 254.3 Relief-device Specification. . . . . . . . . . . .

23、 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 284.4 Installation of Venting Devices. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 285 Testing of Venting Devices. . .

24、. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 295.1 General . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 295.

25、2 Flow-test Apparatus . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 295.3 Method for Determining Capacities. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .

26、 . . . . . . 335.4 Production Testing . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 346 Manufacturers Documentation and Marking of Venting Devices . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .

27、 . . 356.1 Documentation. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 356.2 Marking . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .

28、. . . . . . . . . . . . . . . . . . . . . . . 35Annex A (informative) Alternative Calculation of Normal Venting Requirements . . . . . . . . . . . . . . . . . . . . . . . . 37Annex B (informative) Basis of Emergency Venting for Table 7 and Table 8. . . . . . . . . . . . . . . . . . . . . . . . . . .

29、 . 46Annex C (informative) Types and Operating Characteristics of Venting Devices . . . . . . . . . . . . . . . . . . . . . . . . 51Annex D (informative) Basis of Sizing Equations . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 59Annex E (informati

30、ve) Basis for Normal Out-breathing and Normal Inbreathing. . . . . . . . . . . . . . . . . . . . . . . . . 73Annex F (informative) Guidance for inert-gas Blanketing of Tanks for Flashback Protection. . . . . . . . . . . . . . 75Annex G (informative) Explanation of Differences in Thermal Inbreathing

31、Using the General Method and Annex A Method. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 78Bibliography . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .

32、. . . . . . . . . . . . . . . . . . . . . . . . . . . . 83Figures1 Test Apparatus for Flow Testing of Venting Devices . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 302 Typical Ratio Limits for Capacity Testing of Venting Devices Using the Coefficient of Discharg

33、e Method . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 33B.1 Curve for Determining Requirements for Emergency Venting During Fire Exposure (SI Units) . . . . . . . 49B.2 Curve for Determining Requirements

34、 for Emergency Venting During Fire Exposure (USC Units). . . . . 50C.1 Open Vent. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 51C.2 Side-by-side Pressure/Vacuum Vent. . . . . . . . . . . . .

35、 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 54C.3 Large, Weight-loaded Emergency Vent. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 54vContentsPageC.4 Direct-acting Vents . . . . . . . . . . . . .

36、 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 55C.5 Pilot-operated Pressure Vent (Single Diaphragm). . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 56C.6 Pilot-operated Pressure/Vacuum (Doub

37、le Diaphragm). . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 57D.1 Isentropic Expansion Coefficient . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 70F.1 Trip Pressure Diagram for Nitrogen Blanketin

38、g. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 77G.1 Surface to Volume Ratio for Conical Roof Tanks . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 79G.2 Rate of Change of Tank Vapor Space Temperature Used in t

39、he Two Sizing Methods . . . . . . . . . . . . . . . 80G.3 Maximum Inbreathing for Various Tanks Sizes; Solid Black LinesThermodynamic Model;Solid CrossesAnnex A Method; Red Line V = 5V0.7. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 81G.4 Rate of Change of Tank Va

40、por Space Temperature vs Rain Density. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 82Tables1 Y-factor for Various Latitudes . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 102 C-factors . . . . . . . . . . . . .

41、. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 113 Heat Input, Q (Expressed in SI Units) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 134 Heat Input,

42、Q (Expressed in USC Units) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 145 Venting Capacity (Expressed in SI Units) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 146 Venting Capaci

43、ty (Expressed in USC Units). . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 157 Emergency Venting Required for Fire Exposure vs Wetted Surface Area (Expressed in SI Units). . . . . 168 Emergency Venting Required for Fire Exposure vs Wetted Surface A

44、rea (Expressed in USC Units) . . 179 Environmental Factors for Nonrefrigerated Aboveground Tanks (Expressed in SI and USC Units) . . . 1810 Maximum Allowable Leak Rates . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 34A.1 Normal

45、Venting Requirements (Expressed in SI Units) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 40A.2 Normal Venting Requirements (Expressed in USC Units) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 40A.3 Normal Venting Requirements for Th

46、ermal Effects (Expressed in SI Units) . . . . . . . . . . . . . . . . . . . . . . . 41A.4 Normal Venting Requirements for Thermal Effects (Expressed in USC Units) . . . . . . . . . . . . . . . . . . . . . 42D.1 Guidance on Converting Calculated Flows to Normal/Standard Conditions. . . . . . . . . .

47、. . . . . . . . . . . . . 67G.1 Surface to Volume Ratio of Small, Medium, and Large Flat Roof Tanks . . . . . . . . . . . . . . . . . . . . . . . . . . 79G.2 Assumptions Used in the Annex A Method and General Method . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 80viIntroductionThis

48、 standard has been developed from the accumulated knowledge and experience of qualified engineers of the oil, petroleum, petrochemical, chemical, and general bulk liquid storage industry.Engineering studies of a particular tank can indicate that the appropriate venting capacity for the tank is not t

49、he venting capacity estimated in accordance with this standard. The many variables associated with tank-venting requirements make it impractical to set forth definite, simple rules that are applicable to all locations and conditions.In this standard, where practical, U.S. customary (USC) units are included in parentheses or in separate tables, for information.vii1 Venting Atmospheric and Low-pressure Storage Tanks 1 Scope This standard covers the normal and emergency vapor venting requirements for aboveground liquid petroleum or petroleum products storage tanks and aboveground an