ANSI ASME A112.19.5-2011 Flush valves and spuds for water closets urinals and tanks《抽水马桶 小便池和水箱的冲洗阀和溢水接管》.pdf

1、Update No. 1ASME A112.19.5-2011/CSA B45.15-11May 2012Note: General Instructions for CSA Standards are now called Updates. Please contact CSA Information Products Sales or visit shop.csa.ca for information about the CSA Standards Update Service.Title: Flush valves and spuds for water closets, urinals

2、, and tanks originally published October 2011The following revisions have been formally approved and are marked by the symbol delta () in the margin on the attached replacement pages:Revised Preface and Clause 2New NoneDeleted None Update your copy by inserting these revised pages.Keep the pages you

3、 remove for reference.J0581QM1ASMECopyright ASME International Provided by IHS under license with ASME Not for ResaleNo reproduction or networking permitted without license from IHS-,-,-INTENTIONALLY LEFT BLANKCopyright ASME International Provided by IHS under license with ASME Not for ResaleNo repr

4、oduction or networking permitted without license from IHS-,-,- The American Society of Mechanical Engineers Canadian Standards Association Flush valves and spuds for water closets, urinals, and tanksMay 2012PrefaceThis is the first edition of ASME A112.19.5/CSA B45.15, Flush valves and spuds for wat

5、er closets, urinals, and tanks.This Standard replaces ASME A112.19.5-2005, Trim for Water-Closet Bowls, Tanks, and Urinals and the requirements in Clauses 4.18.1, 4.18.3, and 5.8.7 of CSA B125.3-11.This Standard is considered suitable for use with conformity assessment within its stated scope.This S

6、tandard was prepared by the ASME/CSA Joint Harmonization Task Group on Plumbing Fixtures, under the jurisdiction of the ASME Standards Committee on Plumbing Materials and Equipment and the CSA Technical Committee on Plumbing Fixtures. The CSA Technical Committee operates under the jurisdiction of th

7、e CSA Strategic Steering Committee on Water Management Products, Materials, and Systems. This Standard has been formally approved by the ASME Standards Committee and the CSA Technical Committee. This Standard was approved as an American National Standard by the American National Standards Institute

8、on September 1, 2011.October 2011ASME Notes:(1) This standard was developed under procedures accredited as meeting the criteria for American National Standards and it is an American National Standard. The Standards Committee that approved the code or standard was balanced to assure that individuals

9、from competent and concerned interests have had an opportunity to participate. The proposed Standard was made available for public review and comment that provides an opportunity for additional public input from industry, academia, regulatory agencies, and the public-at-large.(2) ASME does not “appr

10、ove,” “rate,” or “endorse” any item, construction, proprietary device, or activity.(3) ASME does not take any position with respect to the validity of any patent rights asserted in connection with any items mentioned in this document, and does not undertake to insure anyone utilizing a standard agai

11、nst liability for infringement of any applicable letters patent, nor assume any such liability. Users of a standard are expressly advised that determination of the validity of any such patent rights, and the risk of infringement of such rights, is entirely their own responsibility.(4) Participation

12、by federal agency representative(s) or person(s) affiliated with industry is not to be interpreted as government or industry endorsement of this standard.(5) ASME accepts responsibility for only those interpretations of this document issued in accordance with the established ASME procedures and poli

13、cies, which precludes the issuance of interpretations by individuals.(6) ASME issues written replies to inquiries concerning interpretation of technical aspects of this Standard. All inquiries regarding this Standard, including requests for interpretations, should be addressed to:Secretary, A112 Sta

14、ndards CommitteeThe American Society of Mechanical EngineersThree Park AvenueNew York, NY 10016-5990A request for interpretation should be clear and unambiguous. The request shouldcite the applicable edition of the Standard for which the interpretation is being requested.phrase the question as a req

15、uest for an interpretation of a specific requirement suitable for general understanding and use, not as a request for an approval of a proprietary design or situation. The inquirer may also include any plans or drawings, which are necessary to explain the question; however, they should not contain p

16、roprietary names or information.ASME procedures provide for reconsideration of any interpretation when or if additional information that might affect an interpretation is available. Further, persons aggrieved by an interpretation may appeal to the cognizant ASME Committee.Interpretations are publish

17、ed on the ASME Web site under the Committee Pages at http:/cstools.asme.org/ as they are issued.xiii(Replaces p. xiii, October 2011)Copyright ASME International Provided by IHS under license with ASME Not for ResaleNo reproduction or networking permitted without license from IHS-,-,- The American So

18、ciety of Mechanical EngineersASME A112.19.5-2011/CSA B45.15-11 Canadian Standards AssociationMay 2012CSA Notes:(1) Use of the singular does not exclude the plural (and vice versa) when the sense allows.(2) Although the intended primary application of this Standard is stated in its Scope, it is impor

19、tant to note that it remains the responsibility of the users of the Standard to judge its suitability for their particular purpose.(3) This publication was developed by consensus, which is defined by CSA Policy governing standardization Code of good practice for standardization as “substantial agree

20、ment. Consensus implies much more than a simple majority, but not necessarily unanimity”. It is consistent with this definition that a member may be included in the Technical Committee list and yet not be in full agreement with all clauses of this publication.(4) To submit a request for interpretati

21、on of CSA Standards, please send the following information to inquiriescsa.ca and include “Request for interpretation” in the subject line:(a) define the problem, making reference to the specific clause, and, where appropriate, include an illustrative sketch;(b) provide an explanation of circumstanc

22、es surrounding the actual field condition; and(c) where possible, phrase the request in such a way that a specific “yes” or “no” answer will address the issue.Committee interpretations are processed in accordance with the CSA Directives and guidelines governing standardization and are published in C

23、SAs periodical Info Update, which is available on the CSA website at http:/standardsactivities.csa.ca.(5) CSA Standards are subject to periodic review, and suggestions for their improvement will be referred to the appropriate committee. To submit a proposal for change to CSA Standards, please send t

24、he following information to inquiriescsa.ca and include “Proposal for change” in the subject line:(a) Standard designation (number);(b) relevant clause, table, and/or figure number;(c) wording of the proposed change; and(d) rationale for the change.(6) Attention is drawn to the possibility that some

25、 of the elements of this Standard may be the subject of patent rights. CSA is not to be held responsible for identifying any or all such patent rights. Users of this Standard are expressly advised that determination of the validity of any such patent rights is entirely their own responsibility.(Repl

26、aces p. xiv, October 2011)xivCopyright ASME International Provided by IHS under license with ASME Not for ResaleNo reproduction or networking permitted without license from IHS-,-,- The American Society of Mechanical Engineers Canadian Standards AssociationFlush valves and spuds for water closets, u

27、rinals, and tanksMay 2012ASME A112.19.5-2011/CSA B45.15-11Flush valves and spuds for water closets, urinals, and tanks1 Scope1.1 This Standard covers spuds and flush valves for water closet bowls, tanks, and urinals.1.2 In this Standard, “shall” is used to express a requirement, i.e., a provision th

28、at the user is obliged to satisfy in order to comply with the standard; “should” is used to express a recommendation or that which is advised but not required; and “may” is used to express an option or that which is permissible within the limits of the standard.Notes accompanying clauses do not incl

29、ude requirements or alternative requirements; the purpose of a note accompanying a clause is to separate from the text explanatory or informative material.Notes to tables and figures are considered part of the table or figure and may be written as requirements.Annexes are designated normative (manda

30、tory) or informative (nonmandatory) to define their application.1.3 SI units are the units of record in Canada. In this Standard, the inch/pound units are shown in parentheses.The values stated in each measurement system are equivalent in application; however, each system is to be used independently

31、. Combining values from the two measurement systems can result in non-conformance with this Standard.All references to gallons are to U.S. gallons.For information on the conversion criteria used in this Standard, see Annex A.2 Reference publicationsThis Standard refers to the following publications,

32、 and where such reference is made, it shall be to the edition listed below, including all amendments published thereto.ASME/CSA (The American Society of Mechanical Engineers/Canadian Standards Association)ASME A112.19.2-2008/CSA B45.1-08Ceramic plumbing fixturesASME (The American Society of Mechanic

33、al Engineers)B1.20.1-1983 (R2006)Pipe Threads, General Purpose, InchCSA (Canadian Standards Association)B125.3-11Plumbing fittings1(Replaces p. 1, October 2011)Copyright ASME International Provided by IHS under license with ASME Not for ResaleNo reproduction or networking permitted without license f

34、rom IHS-,-,- The American Society of Mechanical EngineersASME A112.19.5-2011/CSA B45.15-11 Canadian Standards AssociationMay 20123 Definitions and abbreviations3.1 DefinitionsThe following definitions shall apply in this Standard:Flush valve a valve located in a flush tank and used to flush a fixtur

35、e by discharging water into the fixture.Early closure flush valve a valve in which the flush valve seal is adjustable to control the water level.Note: Usually, early closure flush valves are dependent on either a time delay or the distance that the water level drops to control the level at which the

36、 flush valve closes.Flush valve body a fitting that contains a flush valve seat and a means of mounting to a fixtureNote: The means for mounting the body can be threaded or non-threaded, and can be with or without an overflow.Flush valve seal a component of the flush valve that mates against the flu

37、sh valve seat to prevent leakage when the flush valve is closed.Note: Flappers are a type of flush valve seal.Flush valve seat the sealing surface of the flush valve body which, when mated with the flush valve seal, prevents leakage through the flush valve into the fixture.Mounting seal a seal betwe

38、en the flush valve body and the fixture.Spud a fitting used to connect a flushometer valve to a water closet or urinal.Note: Spuds are illustrated in Tables 1 and 2.3.2 AbbreviationsThe following abbreviations shall apply in this Standard:NPS nominal pipe sizeNPSM National Pipe Straight MechanicalPV

39、C polyvinylchloride4 Design requirements4.1 Rated temperaturesFlush valves and spuds shall be designed for rated supply temperatures between 5 and 43 C (40 and 110F).4.2 ThreadsPipe threads shall comply with ASME B1.20.1.4.3 Overflow tubesThe inside diameter of the overflow tube for flush valves int

40、ended to be sold as replacement parts shall be a minimum of 23.4 mm (0.92 in).4.4 Spud dimensionsThreaded spuds shall comply with the dimensions specified in Tables 1 and 2.(Replaces p. 2, October 2011)2Copyright ASME International Provided by IHS under license with ASME Not for ResaleNo reproductio

41、n or networking permitted without license from IHS-,-,-ASME A112.19.5-2011/CSA B45.15-11Flush valves and spuds for water closets, urinals, and tanksCopyright ASME International Provided by IHS under license with ASME Not for ResaleNo reproduction or networking permitted without license from IHS-,-,-

42、Legal Notice for Harmonized StandardJointly Developed by ASME and CSAIntellectual property rights and ownershipAs between The American Society of Mechanical Engineers (ASME) and Canadian Standards Association (CSA) (collectively ASME and CSA) and the users of this document (whether it be in printed

43、or electronic form), ASME and CSA are the joint owners of all works contained herein that are protected by copyright, all trade-marks (except as otherwise noted to the contrary), and all inventions and trade secrets that may be contained in this document, whether or not such inventions and trade sec

44、rets are protected by patents and applications for patents. The unauthorized use, modification, copying, or disclosure of this document may violate laws that protect the intellectual property of ASME and CSA and may give rise to a right in ASME and CSA to seek legal redress for such use, modificatio

45、n, copying, or disclosure. ASME and CSA reserve all intellectual property rights in this document.Disclaimer and exclusion of liabilityThis document is provided without any representations, warranties, or conditions of any kind, express or implied, including, without limitation, implied warranties o

46、r conditions concerning this documents fitness for a particular purpose or use, its merchantability, or its non-infringement of any third partys intellectual property rights. ASME and CSA do not warrant the accuracy, completeness, or currency of any of the information published in this document. ASM

47、E and CSA make no representations or warranties regarding this documents compliance with any applicable statute, rule, or regulation.IN NO EVENT SHALL ASME AND CSA, THEIR RESPECTIVE VOLUNTEERS, MEMBERS, SUBSIDIARIES, OR AFFILIATED COMPANIES, OR THEIR EMPLOYEES, DIRECTORS, OR OFFICERS, BE LIABLE FOR

48、ANY DIRECT, INDIRECT, OR INCIDENTAL DAMAGES, INJURY, LOSS, COSTS, OR EXPENSES, HOWSOEVER CAUSED, INCLUDING BUT NOT LIMITED TO SPECIAL OR CONSEQUENTIAL DAMAGES, LOST REVENUE, BUSINESS INTERRUPTION, LOST OR DAMAGED DATA, OR ANY OTHER COMMERCIAL OR ECONOMIC LOSS, WHETHER BASED IN CONTRACT, TORT (INCLUD

49、ING NEGLIGENCE), OR ANY OTHER THEORY OF LIABILITY, ARISING OUT OF OR RESULTING FROM ACCESS TO OR POSSESSION OR USE OF THIS DOCUMENT, EVEN IF ASME OR CSA HAVE BEEN ADVISED OF THE POSSIBILITY OF SUCH DAMAGES, INJURY, LOSS, COSTS, OR EXPENSES.In publishing and making this document available, ASME and CSA are not undertaking to render pro